Dell PowerEdge 2600 Bedienungsanleitung

www.dell.com | support.dell.com

Dell™ Systems

Installing or Replacing an

ERA/O Card

5U106ebk3.book Page 1 Tuesday, April 15, 2003 1:22 PM

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

Information in this document is subject to change without notice.

Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

April 2003 P/N 5U106 Rev. A03

5U106ebk3.book Page 2 Tuesday, April 15, 2003 1:22 PM

Installing or Replacing an ERA/O Card 1-1

This document explains how to install or replace an Embedded Remote Access Option

(ERA/O) remote management card in your system.

Before You Begin

NOTE: For more information about setting up and using an ERA/O card, see the

remote access controller documentation provided on the documentation CD that came

with your system. The latest information about your ERA/O card is available at the

Dell Support website at support.dell.com.

Before installing the ERA/O card, record the system configuration settings. View the system

configuration screens in the System Setup program and make a note of each setting. See

your User's Guide for instructions about using the System Setup program.

Installing an ERA/O Card

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

1Open the bezel. See "Removing the Bezel" in your Installation and Troubleshooting

Guide.

2Turn off the system, including attached peripherals, and disconnect the system and

peripherals from their electrical outlets.

3Remove the cover. See "Removing the Cover" in your Installation and Troubleshooting

Guide.

5U106ebk3.book Page 1 Tuesday, April 15, 2003 1:22 PM

1-2 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

4Remove the front fan assembly:

aDisconnect the front fan assembly power cable from the front fan connector on

the SCSI backplane board.

bRelease the fan assembly by pressing the release latch. See Figure 1-1.

cSwing the fan assembly up and out of the way.

Figure 1-1. Removing the Front Fan Assembly

release latch

5U106ebk3.book Page 2 Tuesday, April 15, 2003 1:22 PM

Installing or Replacing an ERA/O Card 1-3

5Remove any full-length expansion cards. If you do not have any expansion cards

installed, skip to step 6.

aUnfasten and remove the expansion-card latch. See Figure 1-2.

bDisconnect any cables attached to the card.

cGrasp the expansion card by its edges, and remove it from the expansion-card

connector on the system board.

Figure 1-2. Removing a Full-Length Expansion Card (If Installed)

expansion-card

latch

5U106ebk3.book Page 3 Tuesday, April 15, 2003 1:22 PM

1-4 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

6Remove the expansion-card guide:

aPress the middle of the expansion-card guide in the direction of the SCSI

backplane (away from the system board) and carefully rotate the expansion-card

guide toward the system board until the card guide retention clip unhooks from

the system board. See Figure 1-3.

bSwing the expansion-card guide up and out of the way.

Figure 1-3. Removing the Expansion-Card Guide

expansion-card

guide

retention clip

slot

5U106ebk3.book Page 4 Tuesday, April 15, 2003 1:22 PM

Installing or Replacing an ERA/O Card 1-5

7Install the ERA/O card in the system:

aUnpack the ERA/O card.

If you are replacing an ERA/O card, see "Removing an ERA/O Card" for removal

instructions before continuing with the next step.

bPosition the ERA/O card so that the card connector is directly over the connector

on the system board and the mounting holes in the card line up with the support

posts on the system board. See Figure 1-4.

cPress down until the ERA/O card connector is fully seated in the connector on the

system board and the support posts are secured in the mounting holes on the card.

Figure 1-4. Installing the ERA/O Card

ERA/O card

connector

ERA/O card

system board

support posts (4)

mounting

holes (4)

5U106ebk3.book Page 5 Tuesday, April 15, 2003 1:22 PM

1-6 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

8Reinstall the expansion-card guide:

aHolding the expansion-card guide at a 45-degree angle, insert the two tabs at the

ends of the expansion-card guide base into the slots on the system board. See

Figure 1-5.

bRotate the expansion-card guide down until the clip snaps securely onto the

system board.

Figure 1-5. Reinstalling the Expansion-Card Guide

9Reinstall expansion cards that you removed:

aPosition the expansion card so that the card-edge connector aligns with the

expansion-card connector on the system board. See Figure 1-2.

bInsert the card-edge connector firmly into the expansion-card connector until the

card is fully seated.

cWhen the card is seated in the connector, close the expansion-card latch.

NOTE: SCSI cables connected from an expansion card to the SCSI backplane

board should be routed under the front fan assembly.

dReconnect all expansion-card cables.

slots (2)

tabs (2)

5U106ebk3.book Page 6 Tuesday, April 15, 2003 1:22 PM

Installing or Replacing an ERA/O Card 1-7

10 Reinstall the front fan assembly:

aPlace the fan assembly in the hinge bracket and swing the fan assembly down until

the release lever snaps into place.

bConnect the fan assembly power cable to the front fan connector on the SCSI

backplane board.

11 Replace the system cover. See "Replacing the Cover" in your Installation and

Troubleshooting Guide.

NOTE: If the server management Ethernet connector has not been used before,

remove the cover that protects the connector before connecting a network cable. See

Figure 1-6 for the location of the connector.

12 Connect a network cable to the 10-Mbps server management Ethernet connector on

the system back panel. See Figure 1-6.

Figure 1-6. Server Management Ethernet Connector

13 Reconnect the system and peripherals to their electrical outlets, and turn them on.

14 Close the bezel.

15 Update the ERA/O card with the latest version of the ERA/O firmware, available at the

Dell Support website at support.dell.com.

See the RAC documentation provided on the documentation CD for

information about updating the firmware.

server management

Ethernet connector

5U106ebk3.book Page 7 Tuesday, April 15, 2003 1:22 PM

1-8 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

Removing an ERA/O Card

NOTICE: Do not attempt to disconnect the ERA/O card from the connector on the

system board until you have unfastened the card from each of the four support posts.

1Unfasten each of the support posts from the card:

aCompress the clasp at the top of the support post while carefully lifting up on the

corner of the card to unseat the post. See Figure 1-7.

bRepeat step a for each support post.

2Lift the ERA/O card straight up and out of the chassis.

Figure 1-7. Removing an ERA/O Card

ERA/O card

connector

ERA/O card

system board support posts (4)

mounting holes (4)

5U106ebk3.book Page 8 Tuesday, April 15, 2003 1:22 PM

Andere Handbücher für PowerEdge 2600

Inhaltsverzeichnis

Sprachen:

Andere Dell Computerhardware Handbücher

Dell

Dell PowerEdge 2600 Bedienungsanleitung

Dell

Dell PowerEdge 2600 Bedienungsanleitung

Dell

Dell PowerEdge 1650 Bedienungsanleitung

Dell

Dell Embedded Box PC5000 Bedienungsanleitung

Dell

Dell TrueMobile 1180 Bedienungsanleitung

Dell

Dell qlogic qla2100 Bedienungsanleitung

Dell

Dell PowerEdge S130 Bedienungsanleitung

Dell

Dell PowerEdge 1650 Bedienungsanleitung

Dell

Dell PowerProtect DM5500 Bedienungsanleitung

Dell

Dell Latitude ON Bedienungsanleitung

Dell

Dell PointBlank DPB2701 Bedienungsanleitung

Dell

Dell PowerEdge T710 Technisches Handbuch

Dell

Dell POWEREDGE RAID H700 Bedienungsanleitung

Dell

Dell PowerEdge 64 Series Kurzanleitung

Dell

Dell Dimension 4600 Series Bedienungsanleitung

Dell

Dell Precision FX100 Betriebsanleitung

Dell

Dell PowerEdge systems 6300 Service-Handbuch

Dell

Dell PowerEdge C6220 II Kurzanleitung

Dell

Dell ADVANCED PORT REPLICATOR Bedienungsanleitung

Dell

Dell XPS 8960 Bedienungsanleitung

Dell

Dell Mellanox ConnectX-3 Bedienungsanleitung

Dell

Dell POWEREDGE RAID H700 Kurzanleitung

Dell

Dell OptiPlex HUB Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung