Dell PowerEdge C8220X Bedienungsanleitung

Dell PowerEdge C8220X

Tesla K20 GPGPU Card

Installation Guide

Regulatory Model: B06B

Regulatory Type: B06B001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if

instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Intel is a registered trademark of Intel Corporation in the U.S. and other countries. NVIDIA and Tesla

are trademarks and/or registered trademarks of NVIDIA Corporation.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model B06B

Regulatory Type: B06B001

2013 - 02 P/N 38DP3 Rev. A00

Contents 3

Contents

Important Safety Information . . . . . . . . . . . . . . . . . . . . . 5

Recommended Tools . . . . . . . . . . . . . . . . . . . . . . . . . 5

Information You May Need . . . . . . . . . . . . . . . . . . . . . . 6

Tesla K20 GPGPU Cards . . . . . . . . . . . . . . . . . . . . . . . 6

Installing the Front Tesla K20 GPGPU card . . . . . . . . 7

Installing the Back Tesla K20 GPGPU card . . . . . . . 10

Cable Routing Diagram . . . . . . . . . . . . . . . . . . . . . . . 15

4Contents

Important Safety Information

Observe the following safety precautions when installing NVIDIA Tesla K20 GPGPU cards in the

PowerEdge C8220X sled.

WARNING: Working on systems that are still connected to a power supply can be

extremely dangerous.

CAUTION: The sled must be operated with the cover installed to ensure proper cooling.

CAUTION: To ensure proper airflow in the PowerEdge C8000 server enclosure, if a sled

module is removed it should be immediately replaced with another sled or sled blank.

CAUTION: Operating the system for extended periods of time without a sled blank

installed can cause the PowerEdge C8000 server enclosure to overheat.

CAUTION: GPGPU cards can only be installed in the slots on the GPGPU card riser. Do not

attempt to install GPGPU expansion cards directly into the riser connector on the system

board.

NOTE: It is recommended that you always use a static mat and static strap while working on

components in the interior of the system.

To avoid injury to yourself or damage to your system, follow these guidelines:

• Always disconnect the system from the power outlet whenever you are working inside the

system.

• If possible, wear a grounded wrist strap when you are working inside the system.

Alternatively, discharge any static electricity by touching the bare metal chassis of the

system case, or the bare metal body of any other grounded appliance.

• Hold electronic circuit boards by the edges only. Do not touch the components on the

board unless it is necessary to do so. Do not flex or stress the circuit board.

• Leave all components inside the static-proof packaging until you are ready to use the

component for the installation.

• Some cables have a connector with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart,

keep them evenly aligned to avoid bending any connector pins. Also, before you connect a

cable, ensure that both connectors are correctly oriented and aligned.

Recommended Tools

You may need the following items to install NVIDIA Tesla K20 GPGPU cards in the PowerEdge

C8220X sled.

• #1 or #2 Phillips screwdriver

• Static mat

• Static strap

Information You May Need

For information about system features, troubleshooting, and component replacement, see the

PowerEdge C8220X Hardware Owner’s Manual. This document is available at

support.dell.com/manuals.

Tesla K20 GPGPU Cards

Remove the sled from the PowerEdge C8000 server enclosure. For detailed information on

removing the sled, see the

PowerEdge C8220X Hardware Owner’s Manual

Place the sled on a flat, stable surface.

Open the sled. For detailed information on opening the sled, see the

PowerEdge C8220X

Hardware Owner’s Manual

Remove the five M3 screws securing the top cover.

Lift the top cover away from the sled cover.

Figure 1-1. Removing the Top Cover

1 top cover 2 M3 screws (5)

Installing the Front Tesla K20 GPGPU card

Remove the four M3 screws securing the air baffles.

Lift the air baffles out of the sled cover.

Figure 1-2. Removing the Air Baffles

Remove the four M3 screws securing the mounting brackets.

Lift the mounting brackets away from the GPGPU blank. Save the mounting brackets.

Lift the GPGPU blank out of the sled cover. Save the GPGPU blank for future use.

Figure 1-3. Removing the Mounting Brackets and GPGPU Blank

1M3screws(4) 2right air baffle

3 left air baffle 4 GPGPU blank

1 M3 screws (4) 2 front mounting bracket

3 back mounting bracket 4 GPGPU blank

Align the right air baffle with the screw holes on the front of the sled cover.

Secure the right air baffle to the sled cover using the two M3 screws. Tighten the screws to

5.21 in-lbs.

Figure 1-4. Installing the Right Air Baffle

Align the front mounting bracket with the screw holes on the left of the GPGPU card and

secure with two M3 screws. Tighten the screws to 5.21 in-lbs.

Align the back mounting bracket with the screw holes on the right of the GPGPU card and

secure with two M3 screws. Tighten the screws to 5.21 in-lbs.

Figure 1-5. Installing the Mounting Brackets

1 M3 screws (2) 2 right air baffle

1 M3 screws (4) 2 front mounting bracket

3 Tesla K20 GPGPU card 4 back mounting bracket

Connect the power cables to the GPGPU card. Ensure the cables are properly attached.

Connect the emergency throttling cable to the GPGPU card. See Figure 1-17 for the cable

routing diagram.

Figure 1-6. Connecting the Power and Emergency Throttling Cables

Align and insert the GPGPU card assembly into the front GPGPU card riser connector until

the card is fully seated.

Secure the GPGPU card to the front of the sled cover using the four M3 screws, working in a

clockwise sequence. Tighten the screws to 5.21 in-lbs.

Figure 1-7. Installing the Front GPGPU Card Assembly

1, 2 power cables 3 emergency throttling cable

1 M3 screws (4) 2 Tesla K20 GPGPU card assembly

3 front GPGPU card riser

Align the left air baffle with the screw holes on the front of the sled cover.

Secure the left air baffle to the sled cover using the two M3 screws. Tighten the screws to

5.21 in-lbs.

Figure 1-8. Installing the Left Air Baffle

Installing the Back Tesla K20 GPGPU card

Release the cables from the retaining clips and slightly lift the cables to access the screws on

the sled cover.

Figure 1-9. Releasing the Power and Emergency Throttling Cables

1 left air baffle 2 M3 screws (2)

3 Tesla K20 GPGPU card assembly

1 power and emergency throttling cables

Andere Handbücher für PowerEdge C8220X

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Computerhardware Handbücher

Dell

Dell PowerEdge 800 Bedienungsanleitung

Dell

Dell PowerEdge 1650 Bedienungsanleitung

Dell

Dell PowerEdge 2600 Bedienungsanleitung

Dell

Dell PowerConnect W-7200 Series Bedienungsanleitung

Dell

Dell PR03X Bedienungsanleitung

Dell

Dell OptiPlex HUB Bedienungsanleitung

Dell

Dell PointBlank DPB2701 Bedienungsanleitung

Dell

Dell PowerEdge 1650 Bedienungsanleitung

Dell

Dell PowerEdge S130 Bedienungsanleitung

Dell

Dell Mellanox ConnectX-3 Bedienungsanleitung

Dell

Dell 6 series Bedienungsanleitung

Dell

Dell PowerEdge 1650 Bedienungsanleitung

Dell

Dell PowerProtect DM5500 Bedienungsanleitung

Dell

Dell PowerEdge H730P Bedienungsanleitung

Dell

Dell Embedded Box PC 5000 Bedienungsanleitung

Dell

Dell Precision R5500 Bedienungsanleitung

Dell

Dell A2463645 - 2 GB Memory Bedienungsanleitung

Dell

Dell Embedded Box PC5000 Bedienungsanleitung

Dell

Dell Micro-USB dongle Bedienungsanleitung

Dell

Dell PowerEdge systems 6300 Service-Handbuch

Dell

Dell PowerEdge 64 Series Kurzanleitung

Dell

Dell PowerVault 770N Technisches Handbuch

Dell

Dell ChromeBox For Meetings Bedienungsanleitung

Dell

Dell POWEREDGE RAID H700 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung