Dell Inspiron 518 Bedienungsanleitung

Dell™Inspiron™518/519ServiceManual

Model: DCMF

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

©2008DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Inspiron are trademarks of Dell Inc.; AMD is a trademark of Advanced Micro Devices Inc.; Microsoft and Windows are either

trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

May2008Rev.A00

Technical Overview



Before You Begin



Removing the Computer Cover



Replacing the Front Panel



Replacing Memory Module(s)



Replacing a PCI/PCI Express Card



Replacing Drives



Replacing Fans

Replacing the Front I/O Panel



Replacing the Processor



Replacing the System Board



Replacing the Power Supply



Replacing the Battery



Replacing the Computer Cover



System Setup

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Before You Begin

Dell™Inspiron™518/519ServiceManual

Technical Specifications

Recommended Tools

Turning Off Your Computer

Safety Instructions

This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the

following conditions exist:

lYou have performed the steps in Turning Off Your Computer and Safety Instructions.

lYou have read the safety information that shipped with your computer.

lA component can be replaced or—if purchased separately—installed by performing the removal procedure in reverse order.

Technical Specifications

For information on technical specifications of your computer, see the Quick Reference Guide that shipped with your computer or see the Dell Support website at

support.dell.com.

Recommended Tools

The procedures in this document may require the use of a small Phillips screwdriver size #2.

Turning Off Your Computer



1. Shut down the operating system.



2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut

down your operating system, press and hold the power button for about 4 seconds to turn them off.

Safety Instructions

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your own personal safety.



1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.



2. Turn off your computer (see Turning Off Your Computer).



3. Disconnect all telephone or network cables from the computer.



4. Disconnect your computer and all attached devices from their electrical outlets.



NOTICE: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE: Onlyacertifiedservicetechnicianshouldperformrepairsonyourcomputer.DamageduetoservicingthatisnotauthorizedbyDell™isnot

covered by your warranty.

NOTICE: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if

you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly

aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer.

NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

5. Press and hold the power button while the system is unplugged to ground the system board.

Back to Contents Page



NOTICE: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the

computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

Back to Contents Page

Replacing a PCI/PCI Express Card

Dell™Inspiron™518/519ServiceManual

Removing a PCI/PCI Express Card

Installing a PCI/PCI Express Card

Replacing the Card Retention Bracket

Configuring Your Computer After Removing or Installing a PCI/PCI Express Card



Removing a PCI/PCI Express Card



1. Follow the procedures in Before You Begin.



2. Uninstall the card's driver and software from the operating system. For more information, see the Quick Reference Guide.



3. Remove the computer cover. See Removing the Computer Cover.



4. Remove the screw holding the card retention bracket.



5. Lift the card retention bracket and set it aside in a secure place.



6. If necessary, disconnect any cables connected to the card.

lFor a PCI card, grasp the card by its top corners, and ease it out of its connector.

lFor a PCI Express card, pull the securing tab, grasp the card by its top corners, and then ease it out of its connector.



7. If you are replacing an existing card, go to step 6 of Installing a PCI/PCI Express Card.



8. Install a filler bracket in the empty card-slot opening.



9. Replace the card retention bracket. See Replacing the Card Retention Bracket.



10. Replace the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on.



11. To complete the removal procedure, see Configuring Your Computer After Removing or Installing a PCI/PCI Express Card.

Installing a PCI/PCI Express Card



1. Follow the procedures in Before You Begin.



2. Remove the computer cover. See Removing the Computer Cover.



CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

card retention bracket

filler bracket

NOTICE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust

and dirt out of your computer.



3. Remove the screw holding the card retention bracket.



4. Lift the card retention bracket and set it aside in a secure place.



5. Remove the filler bracket to create a card-slot opening.



6. Prepare the card for installation.

See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your

computer.



7. Align the card with the connector.



8. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.



9. Replace the card retention bracket. See Replacing the Card Retention Bracket.



10. Connect any cables that should be attached to the card.

See the documentation for the card for information about the card's cable connections.



11. Replace the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on.



12. To complete the installation, see Configuring Your Computer After Removing or Installing a PCI/PCI Express Card.

Replacing the Card Retention Bracket

NOTE: If you are installing a PCI Express card into the x16 connector, ensure that the securing slot is aligned with the securing tab.

PCI Express x16 card

securing tab

PCI Express x1 card

PCI Express x1 card slot

PCI Express x16 card slot



alignment bar

fully-seated card

not fully-seated card

alignment guide

bracket within slot

bracket caught outside of slot

NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or

cause damage to the equipment.

Replace the card retention bracket ensuring that:

lThe guide clamp is aligned with the guide notch.

lThe tops of all cards and filler brackets are flush with the alignment bar.

lThe notch in the top of the card or filler bracket fits around the alignment guide.

Configuring Your Computer After Removing or Installing a PCI/PCI Express Card

Back to Contents Page



alignment guide

filler bracket

alignment bar

card retention bracket

guide clamp (2)

guide notch (2)

NOTE: For information on location of connectors, see the Quick Reference Guide. For information on installing drivers and software for your card, see the

documentation that shipped with the card.



Installed

Removed

Sound

Card

1. Enter system setup (see

System Setup)

2. Go to Integrated

Peripherals and select

Onboard Audio

Controller, and then

change the setting to

Disabled.

3. Connect the external

audio devices to the

sound card's connectors.

1. Enter system setup (see

System Setup)

2. Go to Integrated

Peripherals and select

Onboard Audio

Controller, and then

change the setting to

Enabled.

3. Connect the external

audio devices to the

computer's back panel

connectors.

Network

Card

1. Enter system setup (see

System Setup)

2. Go to Integrated

Peripherals and select

Onboard LAN Controller,

and then change the

setting to Disabled.

3. Connect the network

cable to the network

card's connector.

1. Enter system setup (see

System Setup)

2. Go to Integrated

Peripherals and select

Onboard LAN Controller,

and then change the

setting to Enabled.

3. Connect the network

cable to the integrated

network connector.

Back to Contents Page

Replacing the Battery

Dell™Inspiron™518/519ServiceManual



1. Record all the screens in system setup (see System Setup) so that you can restore the correct settings in step 10.



2. Follow the procedures in Before You Begin.



3. Remove the computer cover (see Removing the Computer Cover).



4. Locate the battery socket (see System Board Components).



5. Carefully press the battery release lever away from the battery and the battery will pop out.



6. Remove the battery from the system and properly dispose of the battery.



7. Insert the new battery into the socket with the side labeled "+" facing up, then snap the battery into place.



8. Replace the computer cover (see Replacing the Computer Cover).



9. Connect your computer and devices to electrical outlets, and then turn them on.



10. Enter system setup (see System Setup) and restore the settings you recorded in step 1.

Back to Contents Page



CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION: A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the

manufacturer. Discard used batteries according to the manufacturer's instructions.

NOTICE: If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Ensure that the object is

inserted between the battery and the socket before you attempt to pry out the battery. Otherwise, you may damage the system board by prying off

the socket or by breaking circuit traces on the system board.

battery (positive side)

battery release lever

battery (positive side)

battery release lever

Back to Contents Page

Replacing the Computer Cover

Dell™Inspiron™518/519ServiceManual



1. Ensure that all cables are connected, and fold cables out of the way.



2. Ensure that no tools or extra parts are left inside the computer.



3. Align the tabs at the bottom of the computer cover with the slots located along the edge of the computer.



4. Press the computer cover down and slide it towards the front of the computer until you feel the computer cover is securely installed.



5. Ensure that the cover is seated correctly.



6. Replace and tighten the two screws that secure the computer cover, using a screwdriver.



7. Turn the computer to the upright position.



8. Connect your computer and devices to electrical outlets, and turn them on.

Back to Contents Page



CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION: Do not operate your equipment with any cover(s) (including computer covers, front panel, filler brackets, front-panel inserts, etc.)

removed.

front of the computer

computer cover

slot

computer cover tab

NOTICE: Ensure that none of the system air-vents are blocked. Blocking them would cause serious thermal problems.

Back to Contents Page

Removing the Computer Cover

Dell™Inspiron™518/519ServiceManual



1. Follow the procedures in Before You Begin.



2. Lay your computer on its side with the computer cover facing up.



3. Open the padlock, if applicable.



4. Loosen the two thumbscrews.



5. Pull the cover grip towards the back of the computer to release the cover.



6. Set the cover aside in a secure location.

To replace the computer cover, see Replacing the Computer Cover.

Back to Contents Page



CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

CAUTION: To guard against likelihood of electric shock, laceration by moving fan blades or other unexpected injuries, always unplug your

computer from the electrical outlet before removing the cover.

NOTICE: Ensure that sufficient space exists to support the system with the cover removed—at least 30 cm (1 ft.) of desktop space.

computer cover

front of computer

thumbscrew (2)

cover grip

Back to Contents Page

Replacing the Processor

Dell™Inspiron™518/519ServiceManual

Removing the Processor

Installing the Processor



Removing the Processor



1. Follow the procedures in Before You Begin.



2. Remove the computer cover (see Removing the Computer Cover).



3. Disconnect the power cables from the ATX_POWER and ATX_CPU connectors (see System Board Components) on the system board.



4. Remove the processor fan and heat sink assembly from the computer (see Replacing the Processor Fan and Heat Sink Assembly).



5. Press and push the release lever down and out to release it from the tab that secures it.



6. Open the processor cover, if applicable.



Dell™Inspiron™518



Dell Inspiron 519

CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE: Do not perform the following steps unless you are familiar with hardware removal and replacement. Performing these steps incorrectly could

damage your system board. For technical service, see the Quick Reference Guide.

CAUTION: Despite having a plastic shield, the heat sink assembly may be very hot during normal operation. Be sure that it has had sufficient time

to cool before you touch it.

NOTE: Unless a new heat sink is required for the new processor, reuse the original heat sink assembly when you replace the processor.

processor cover

processor

socket

release lever

Andere Handbücher für Inspiron 518

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Desktop Handbücher

Dell

Dell 3250 Bedienungsanleitung

Dell

Dell OptiPlex 330 Bedienungsanleitung

Dell

Dell Precision 7865 Tower Bedienungsanleitung

Dell

Dell inspiron 27 7000 Bedienungs- und Wartungshandbuch

Dell

Dell D31M Bedienungsanleitung

Dell

Dell XPS 730X Bedienungsanleitung

Dell

Dell OptiPlex 5080 Bedienungsanleitung

Dell

Dell OptiPlex 7060 Tower Benutzerhandbuch

Dell

Dell OptiPlex 7050 Micro Bedienungsanleitung

Dell

Dell Precision Workstation T1500 Bedienungsanleitung

Dell

Dell Precision R5400 Bedienungsanleitung

Dell

Dell 320N Bedienungsanleitung

Dell

Dell Vostro V 3900 Bedienungsanleitung

Dell

Dell Dimension 5150C Bedienungsanleitung

Dell

Dell Alienware X51 Bedienungsanleitung

Dell

Dell OptiPlex GX270 Bedienungsanleitung

Dell

Dell OptiPlex 7070 Ultra Bedienungs- und Wartungshandbuch

Dell

Dell PowerEdge 4200 Series Bedienungsanleitung

Dell

Dell OptiPlex HUB Bedienungsanleitung

Dell

Dell OptiPlex 3040 Bedienungsanleitung

Dell

Dell EMC PowerEdge XR11 Handbuch

Dell

Dell T3400 - Precision - 2 GB RAM Bedienungsanleitung

Dell

Dell Vostro 270s Betriebsanleitung

Dell

Dell Inspiron One 2310 Intel Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung