Dell OptiPlex GX1 Bedienungsanleitung

Contents: Dell OptiPlex GX1 Small-Form-Factor Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/index.htm[2/21/2013 11:45:27 AM]

Dell™ OptiPlex™ GX1 Small-Form-Factor Systems Service Manual

Removing and Replacing Parts

Notes, Notices, and Cautions

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic

type. These blocks are notes, notices, and cautions, and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your system.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, OptiPlex, and the DELL logo are trademarks of Dell Computer Corporation; Microsoft, MS-

DOS, and Windows NT are registered trademarks of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or

their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

Initial release: Jun 1999

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

Back to Contents Page

Removing and Replacing Parts: Dell™ OptiPlex™ GX1 Small-

Form-Factor Systems Service Manual

Overview System Power Supply

Recommended Tools Riser Board

Precautionary Measures System Board Components

Internal Views Expansion-Card Cage

Computer Cover Expansion Cards

Eject and Power Buttons DIMMs

Control Panel Microprocessor/Heat Sink Assembly

Chassis Intrusion Switch System Battery

Drives System Board

Overview

This section provides procedures for removing and replacing the components, assemblies, and

subassemblies in the Dell OptiPlex small-form-factor chassis GX1 system.

Unless otherwise noted, each procedure assumes that the following conditions exist:

You have performed the steps in "Precautionary Measures."

You have removed the computer cover.

You can replace or reinstall a part by performing the removal procedure in reverse order unless

additional information is provided.

Recommended Tools

Most of the procedures in this manual require the use of one or more of the following tools:

#1 and #2 Phillips-head screwdrivers

1/4-inch nut driver

Also, use a wrist grounding strap as explained in "Precautionary Measures."

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

Precautionary Measures

Before you perform any procedures in this manual, take a few moments to read the following caution for your

personal safety and to prevent damage to the system from ESD.

CAUTION: FOR YOUR PERSONAL SAFETY AND PROTECTION OF THE EQUIPMENT

Before you start to work on the system, perform the following steps in the sequence listed:

1. Turn off the computer and all peripherals.

2. Disconnect the computer and peripherals from their AC power sources. Also, disconnect any

telephone or telecommunication lines from the computer. Doing so reduces the potential for

personal injury or shock.

3. If you are disconnecting a peripheral from the computer or are removing a component from the

system board, wait 10 to 20 seconds after disconnecting the computer from AC power before

disconnecting the peripheral or removing the component to avoid possible damage to the

system board.

4. Wear a wrist grounding strap, and clip it to an unpainted metal surface, such as the padlock loop

on the back of the chassis. If a wrist grounding strap is not available, touch any unpainted metal

surface on the back of the computer or on the computer chassis, such as the power supply, to

discharge any static charge from your body before touching anything inside the computer.

While you work, periodically touch an unpainted metal surface on the computer chassis to

dissipate any static electricity that might harm internal components. Also avoid touching

components or contacts on a card and avoid touching pins on a chip.

5. Verify that the auxiliary power indicator on the riser board is not on. If it is on, you may need to

wait 10 to 30 seconds for it to go out (see Figure 20).

Internal Views

Figure 1 shows a top view of the chassis to help you orient yourself when you work inside the computer.

Figure 1. Orientation View

1System board

2Diskette drive

3Hard-disk drive

4CD-ROM drive

5Power supply

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

Figure 2 shows the chassis with the cover removed.

Figure 2. Inside the Chassis

1CD-ROM drive interface cable

2Externally accessible upper drive

bay

3Hard-disk drive

4Diskette-drive interface cable

5Hard-disk drive interface cable

6Expansion-card cage

7System board

8Expansion-card slots

9I/O ports and connectors

10 AC power receptacle

11 Security cable slot

12 Power supply

13 Chassis intrusion switch

Computer Cover

Figure 3. Computer Cover Removal

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

To remove the computer cover, perform the following steps:

1. Be sure the padlock ring is pushed into the cover.

2. Press in on the two securing buttons until the cover is free to swing up (see Figure 3).

3. Raise the back of the cover, and pivot it toward the front of the computer.

4. Lift the cover off the hooks at the front of the chassis.

5. Disengage the tabs that secure the cover to the top of the chassis, and lift the cover away.

Figure 4. Computer Cover Replacement

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

To replace the computer cover, perform the following steps:

1. Face the front of the computer and hold the cover at a slight angle (see Figure 4).

2. Align the bottom of the cover with the bottom of the chassis and insert the hooks on the cover into the

recessed slots on the computer chassis so that the tabs catch the hooks inside the slots.

3. Pivot the cover down toward the back of the chassis and into position.

Make sure that the securing buttons click into place.

Eject and Power Buttons

Figure 5. Eject and Power Button Removal

1Diskette eject button

2Power button

To remove the eject and power buttons, perform the following steps:

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

1. Lay the computer cover on a flat work surface, with the inside of the top cover facing up.

2. To remove the 3.5-inch diskette-drive eject button, pull gently on the plastic part of the button until it

comes free.

3. To remove the power button, use a small screwdriver and push in the two plastic clips that hold the

button to the bezel. When these clips are released, the button and the spring come free from the bezel.

Control Panel

Figure 6. Control Panel Removal

1Screw

2Control panel

To remove the control panel, perform the following steps:

1. Remove the drive shelf.

2. Remove the power supply.

3. Disconnect the control panel cable from the control panel connector on the system board (see "System

Board Labels" for the location of the PANEL connector).

Note the routing of the control panel cable as you remove it from the chassis.

4. Remove the mounting screw that secures the control panel to the chassis.

5. Disconnect the chassis intrusion switch cable connector from the control panel.

6. Remove the control panel cable.

7. Remove the control panel from the chassis.

Note the routing of the control panel cable as you remove it from the chassis.

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

When you install the replacement control panel, be sure to put the right side of the control panel behind the

mounting tab.

Chassis Intrusion Switch

Figure 7. Chassis Intrusion Switch Removal

1Control panel

2Chassis intrusion

switch

To remove the chassis intrusion switch, perform the following steps:

1. Remove the drive shelf.

2. Remove the power supply.

3. Remove the control panel.

4. Disconnect the chassis intrusion switch cable connector from the control panel.

Note the routing of the chassis intrusion cable as you remove the cable from the chassis. Chassis

hooks may hold the cable in place inside the chassis.

5. Slide the chassis intrusion switch out of its slot and remove the switch and its attached cable from the

chassis.

6. Install the replacement chassis intrusion switch and cable.

7. To reset the chassis intrusion detector, enter the System Setup program and reset Chassis Intrusion

to Not Detected (see your online System User's Guide for instructions).

Drives

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

NOTE: In all of the following procedures, left and right refer to your left and right as you face the front

of the computer.

Figure 8. Drive Locations

1Chassis intrusion switch

2CD-ROM drive

33.5-inch diskette drive

4Hard-disk drive

Preliminary Steps

You must remove the drive shelf before removing the 3.5-inch diskette drive, the CD-ROM drive, the hard-

disk drive, the control panel, the chassis intrusion switch, or the power supply.

Figure 9. Drive Shelf Removal

1Drive shelf

2Release tabs (2)

To remove the drive shelf from the chassis, perform the following steps:

1. Disconnect the power and interface cables from the diskette drive and CD-ROM drive.

2. Press inward on the two drive shelf release tabs, and pull the shelf forward and out of the chassis (see

Removing and Replacing Parts: Dell OptiPlex GX1 Systems Service Manual

file:///C|/infodev/2013/eDoc/OpGX1/SM/remsff.htm[2/21/2013 11:45:32 AM]

Figure 9).

Hard-Disk Drive

Figure 10. Hard-Disk Drive/Bracket Removal

1Drive bracket

2Release tabs (2)

CAUTION: To avoid the possibility of electric shock, turn off the computer and any peripherals,

disconnect them from electrical outlets, and then wait at least 5 seconds before you remove

the computer cover. Also, before you remove a drive, see the other precautions in

"Precautionary Measures."

To remove the hard-disk drive and its bracket from the chassis, perform the following steps:

1. If you are replacing a hard-disk drive that contains data you want to keep, make a backup copy of your

files before you continue this procedure.

2. Remove the computer cover if not already removed.

3. Remove the drive shelf.

4. Squeeze the tabs on each side of the hard-disk drive/bracket, and pull the hard-disk drive/bracket

forward about one inch (see Figure 10).

5. Disconnect the power and interface cables from the back of the drive.

6. Lift the hard-disk drive/bracket away from the chassis.

7. Lay the hard-disk drive/bracket on an antistatic surface with its bracket facing up.

8. Remove the four screws securing the hard-disk drive to the bottom of the bracket (see Figure 11).

Figure 11. Drive Bracket Removal

Andere Handbücher für OptiPlex GX1

Inhaltsverzeichnis

Andere Dell Desktop Handbücher

Dell

Dell XPS 710 Bedienungsanleitung

Dell

Dell GX260 - Optiplex Pentium 4 2.0GHz 512MB 40GB... Bedienungsanleitung

Dell

Dell Inspiron 20 3000 Series Bedienungsanleitung

Dell

Dell Studio Desktop Bedienungsanleitung

Dell

Dell Precision T3610 Betriebsanleitung

Dell

Dell OptiPlex FX160 Bedienungsanleitung

Dell

Dell OptiPlex HUB Bedienungsanleitung

Dell

Dell Vostro 3460 Bedienungs- und Wartungshandbuch

Dell

Dell OptiPlex HUB Bedienungsanleitung

Dell

Dell Precision Workstation T1500 Bedienungsanleitung

Dell

Dell OptiPlex GX620 Bedienungsanleitung

Dell

Dell Dimension 4500 Bedienungsanleitung

Dell

Dell OptiPlex GX1 Low-Profile Managed PC Systems Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3656 Bedienungsanleitung

Dell

Dell OptiPlex VDI Blaster Edition Bedienungsanleitung

Dell

Dell Vostro 3650 Bedienungsanleitung

Dell

Dell Latitude 7000 Series Bedienungs- und Wartungsanleitung

Dell

Dell OptiPlex GXa Bedienerhandbuch

Dell

Dell Precision T3500 Kurzanleitung

Dell

Dell Dimension E520 Bedienungsanleitung

Dell

Dell Dimension 9100 Bedienungsanleitung

Dell

Dell XPS 700 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung

Lenovo

Lenovo ThinkCentre M75e Bedienungsanleitung

Compaq

Compaq iPAQ Internet Device Bedienungsanleitung