Dell PowerApp .cache 100 Technisches Handbuch

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge C2100 Bedienungsanleitung

Dell

Dell PowerEdge 1400SC Technisches Handbuch

Dell

Dell PowerEdge 6400 Bedienungsanleitung

Dell

Dell PowerEdge XR4520c Handbuch

Dell

Dell PowerEdge T630 Bedienungsanleitung

Dell

Dell EMC PowerEdge R940 Handbuch

Dell

Dell PowerEdge SC1435 Gebrauchsanweisung

Dell

Dell PowerEdge R620 Bedienungsanleitung

Dell

Dell PowerEdge T20 Bedienungsanleitung

Dell

Dell VTY3T Bedienungsanleitung

Dell

Dell PowerEdge 2300 Bedienungsanleitung

Dell

Dell PowerEdge R830 Bedienungsanleitung

Dell

Dell Force10 S2410-01-10GE-24P Installationshandbuch

Dell

Dell EMC ScaleIO Ready Node 14G Bedienungsanleitung

Dell

Dell Force10 S2410-01-10GE-24P Montage- und Bedienungsanleitung

Dell

Dell Wyse 3030 LT Bedienungsanleitung

Dell

Dell PowerEdge R520 Kurzanleitung

Dell

Dell POWEREDGE R515 Bedienungsanleitung

Dell

Dell E05B001 Bedienungsanleitung

Dell

Dell PowerEdge R620 Bedienungsanleitung

Dell

Dell E28S Series Bedienungsanleitung

Dell

Dell PowerEdge R210 Bedienungsanleitung

Dell

Dell PowerEdge T105 Systems Bedienungsanleitung

Dell

Dell PowerEdge R610 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung















This document updates information contained in your Dell PowerApp 100 appliance

documentation.

If you replace the appliance’s microprocessor and heat sink assembly, you must remove the fan

attached to the top of the replacement microprocessor and heat sink assembly. (For details on

removing the microprocessor, see “Microprocessor” in your Service Manual.)

To install the replacement microprocessor and heat sink assembly, perform the following steps:

1. If applicable, remove the fan from the heat sink in the replacement kit.

The fan will not be used. To remove the fan, gently squeeze the sides of two adjacent cor-

ners on the fan.

2. Gently place the replacement microprocessor into the zero insertion force (ZIF) socket so

that the processor pins mate exactly with the ZIF socket.

Make sure that pin 1 of the microprocessor is oriented correctly in the socket.





3. Swing the ZIF socket arm down until it snaps into the socket tab after the microprocessor is

in place.

4. At the base of the heat sink, remove and discard the protective cover over the thermal

grease by pulling the cover’s tab.

5. Place the heat sink on the microprocessor.

Be careful not to touch the surfaces coated with thermal grease.

The bevelled surface on the heat sink covers the part of the ZIF socket that is not covered by

the microprocessor.

6. Drop the heat sink clip into the heat sink's center groove with the end of the clip that has

two slots facing the front of the ZIF socket.

7. Gently hold the heat sink in place as you press down on the shorter end of the heat sink

clip (the end that has a single slot) until that end snaps into its tab on the back of the ZIF

socket (see Figure 1).



8. Use your thumb to press down on the front end of the heat sink clip (the end that has

two slots) until it snaps into the socket tab.

9. Replace the cover, install the power cord, and reboot the computer.

____________________

Information in this document is subject to change without notice.

© 2000 Dell Computer Corporation. All rights reserved. Printed in the U.S.A.

Trademarks used in this text: Dell, the DELL E COM logo, and PowerApp are trademarks of Dell Computer Corporation. Other

trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their

products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

heat sink clip

microprocessor and

heat sink assembly

tabs on ZIF socket (2)

ZIF socket

ZIF socket

release lever