Dell PowerEdge 1855 Technisches Handbuch
www.dell.com | support.dell.com
Information Update
For instructions on installing your Dell
™
2342M Integrated Fibre Channel Module, refer to the
PowerEdge
™
1855
Installation and Troubleshooting Guide
. Configuration information, drivers, and
a list of EMC-approved software are available on
support.dell.com
.
Using the StorPort Driver with the Microsoft®Windows®
Server 2003 Operating System
If you are using the StorPort driver with the Microsoft
Windows Server 2003 operating system and
do not have Service Pack 1 or later installed, make sure you are using the latest
storport.sys
driver.
Updated StorPort drivers are available from
www.microsoft.com
. Refer to the EMC Support Matrix
(ESM) at
www.emc.com
for the latest required hotfix.
QLogic SANblade Manager Application
At present, the QLogic SANblade Manager application does not support the Dell 2342M
Integrated Fibre Channel Module daughter card for the PowerEdge 1855. When complete, drivers
will be available at
support.dell.com
.
If you need to implement Target Persistent Bindings, download the SANblade CLI available at
www.qlogic.com
in the EMC Approved Software section.
High Availability Clustering with Microsoft Cluster Server
High availability clustering with Microsoft Cluster Server (MSCS) is not supported. Support for
this feature is planned for Q1 2005.
Boot from SAN Option
Under certain SAN configurations, the
Hard Disk Drive Sequence
setting under
BIOS Setup
will
display as
Embedded
, followed by random ASCII characters. This truncated ASCII string
represents the external SCSI TARGET/LUN combination. Select this string to boot your system.
Despite this message, the Boot from SAN function works properly. A future version of the option
ROM (version 1.46 or later) for your fibre channel module will eliminate this issue. When
completed, this update will be available on
support.dell.com
.
November 2004
C8552am1.fm Page 1 Monday, November 22, 2004 1:08 PM
www.dell.com | support.dell.com
Brocade-based Switches May Cause Panic and Reboot
Fibre channel HBA paths may be dropped on hosts using the QLogic 7.00.03 Red Hat
®
Enterprise
Linux (version 3) driver and Brocade-based fibre channel switches running Brocade firmware
versions prior to 4.4.0 or prior to and including 3.2.0, depending on the switch model being used.
The workaround for this issue requires that you disable the FDMI feature in the QLogic 7.00.03
Red Hat Enterprise Linux (version 3) driver by recompiling the driver after performing the
following steps:
1
Contact Dell Technical Support to obtain the
patch_to_fix_mgmt_srv_unresolved_sym
driver patch.
2
In
qla_settings.h
, change
#define REG_FDMI_ENABLE 1
to
#define
REG_FDMI_ENABLE 0
.
3
Change to the directory where the QLogic 7.00.03 Red Hat Enterprise Linux (version 3)
driver source is located and apply the patch:
patch -p1 < patch_to_fix_mgmt_srv_unresolved_sym
4
Rebuild the driver as instructed in the
README.qla2x00
file.
___________________
Information in this document is subject to change without notice.
© 2004 Dell Inc. All rights reserved. Printed in the U.S.A.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, PowerEdge, and the DELL logo are trademarks of Dell Inc.; EMC is the registered trademark
of EMC Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation; Red Hat is a registered
trademark of Red Hat, Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names
or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
C8552am1.fm Page 2 Monday, November 22, 2004 1:08 PM
Andere Handbücher für PowerEdge 1855
4
Inhaltsverzeichnis
Andere Dell Server Handbücher
Dell
Dell PowerEdge M820 Systems Bedienungsanleitung
Dell
Dell PowerEdge 1750 Handbuch
Dell
Dell POWEREDGE R515 Bedienungsanleitung
Dell
Dell PowerEdge R740xd Handbuch
Dell
Dell EMC VxFlex Ready Node Benutzerhandbuch
Dell
Dell Wyse ThinOS T10 Bedienungsanleitung
Dell
Dell External OEMR XL R720XD Kurzanleitung
Dell
Dell PowerEdge T100 Bedienungsanleitung
Dell
Dell PowerEdge 2410 Bedienungsanleitung
Dell
Dell PowerEdge C6220 II Bedienungsanleitung
Dell
Dell PowerEdge M1000e Bedienungsanleitung
Dell
Dell PowerEdge 2950 Technisches Handbuch
Dell
Dell PowerEdge T710 Bedienerhandbuch
Dell
Dell EMC PowerEdge T440 TG9M2 Bedienungsanleitung
Dell
Dell Wyse7020 Bedienungsanleitung
Dell
Dell PowerEdge System 840 MVT01 Bedienungsanleitung
Dell
Dell PowerEdge M910 Kurzanleitung
Dell
Dell PowerEdge M915 Kurzanleitung
Dell
Dell CX700 Bedienungsanleitung
Dell
Dell PowerEdge R210 II Bedienungsanleitung
