Dell PowerEdge 1950 Bedienungsanleitung

Rack Installation Guide

Guide d'installation du rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del rack

www.dell.com | support.dell.com

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, RapidRails, and VersaRails are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own

November 2005 P/N YC588 Rev. A00

Contents 3

Contents

1 Four-Post Rack Installation. . . . . . . . . . . . . . . . . . . . . . . 5

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems . . . . . . . . . . . . . . . . . . . . . 5

General Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rack Requirements for VersaRails . . . . . . . . . . . . . . . . . . . . . . 7

Rack Stabilizer Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Recommended Tools and Supplies . . . . . . . . . . . . . . . . . . . . . . 7

Sliding Rails Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . 8

Static Rails Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Removing the Rack Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Configuring the Sliding Rail Assemblies (Sliding Rail Kits Only). . . . . . . . 13

Installing Chassis Static Rail Modules (Static Rail Kits Only) . . . . . . . . . 14

Installing the Mounting Rails in the Rack . . . . . . . . . . . . . . . . . . . . 15

Installing the System in the Rack . . . . . . . . . . . . . . . . . . . . . . . . 18

Installing a System With Sliding Rails . . . . . . . . . . . . . . . . . . . 18

Installing a System With Static Rails . . . . . . . . . . . . . . . . . . . . 20

Replacing the Rack Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installing the Tray and Cable-Management Arm (Sliding Rail Kits Only) . . . 22

Installing the Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Installing the Cable-Management Arm . . . . . . . . . . . . . . . . . . . 23

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Removing the System From the Rack . . . . . . . . . . . . . . . . . . . . . . 25

Removing a System With Sliding Rails . . . . . . . . . . . . . . . . . . . 25

Removing a System With Static Rails. . . . . . . . . . . . . . . . . . . . 25

4Contents

2 Two-Post Rack Installation . . . . . . . . . . . . . . . . . . . . . . . 27

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

SAFETY: Rack Mounting of Systems . . . . . . . . . . . . . . . . . . . . 27

Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . 28

Recommended Tools and Supplies . . . . . . . . . . . . . . . . . . . . . 28

Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Universal-Hole Spacing Racks . . . . . . . . . . . . . . . . . . . . . . . 30

Wide-Hole Spacing Racks . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installing the Mounting Rails . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Center-Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . 32

Flush-Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Installing Chassis Static Rail Modules . . . . . . . . . . . . . . . . . . . . . 36

Installing the System in the Rack . . . . . . . . . . . . . . . . . . . . . . . . 37

Removing the System From the Rack . . . . . . . . . . . . . . . . . . . . . . 37

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Four-Post Rack Installation 5

Four-Post Rack Installation

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect your system

and working environment from potential damage. For complete safety and regulatory information,

see the

Product Information

Guide

that shipped with your system. Warranty information might be

included in this document or as a separate document.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also refer to the rack installation

documentation accompanying the system and the rack for specific caution statements and

procedures.

Systems are considered to be components in a rack. Thus, "component" refers to any system as well

as to various peripherals or supporting hardware.

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the

front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing

systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under certain

circumstances. Therefore, always install the stabilizer(s) before installing components in the rack.

After installing system/components in a rack, never pull more than one component out of the rack on its slide

assemblies at one time. The weight of more than one extended component could cause the rack to tip over

and may result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a Dell rack

cabinet using the customer rack kit. The installation of your system and rack kit in any other rack cabinet has

not been approved by any safety agencies. It is your responsibility to ensure that the final combination of

system and rack complies with all applicable safety standards and local electric code requirements. Dell

disclaims all liability and warranties in connection with such combinations.

• System rack kits are intended to be installed in a rack by trained service technicians. If you install

the kit in any other rack, be sure that the rack meets the specifications of a Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the rack, a minimum of two

people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack, extended to

the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers

on a single rack or front stabilizers for joined multiple racks before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

6Four-Post Rack Installation

• Make sure that the rack is level and stable before extending a component from the rack.

• Use caution when pressing the component rail release latches and sliding a component into or out

of a rack; the slide rails can pinch your fingers.

• Do not overload the AC supply branch circuit that provides power to the rack. The total rack load

should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in a rack.

General Installation Instructions

This installation guide provides instructions for trained service technicians installing one or more systems

in a rack cabinet. The RapidRails™ rack kit can be installed in all the system manufacturer's rack cabinets

without tools, and the VersaRails™ rack kit can be installed in most industry-standard rack cabinets. The

procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is required for

each system to be installed in the rack cabinet.

This section includes procedures for the following four-post rack kits:

• Sliding rails rack kit

• Static rails rack kit (RapidRails and VersaRails versions)

(See "Two-Post Rack Installation" on page 27 for instructions on installing a static rails kit in a two-post

rack.)

Before You Begin

Before you begin installing your system in the rack, carefully read "Safety Instructions," found earlier

in this guide, as well as the safety instructions found in your Product Information Guide for additional

information.

CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current system

before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on their casters. They do not have brakes. Use

extreme caution while moving the rack cabinet. Retract the leveling feet when relocating the rack cabinet. Avoid

long or steep inclines or ramps where loss of cabinet control may occur. Extend the leveling feet for support and

to prevent the cabinet from rolling.

NOTE: For instructions on installing the system itself, see ""Installing the System in the Rack" on page 18.

Four-Post Rack Installation 7

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect yourself as well as others who

may be involved. Your system may be very large and heavy and proper preparation and planning are important to

prevent injury to yourself and to others. This precaution becomes increasingly important when systems are

installed high up in the rack.

CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for your system.

Using the rack kit for another system may result in damage to the system and personal injury to yourself and to

others.

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that meets the

specifications of American National Standards Institute (ANSI)/Electronic Industries Association (EIA) standard

ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and Deutsche Industrie Norm (DIN) 41494.

One rack kit is required for each system that is installed in a rack.

Rack Stabilizer Feet

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the front

stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing systems in a

rack could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.

Therefore, always install the stabilizer(s) before installing components in the rack.

The stabilizer feet help prevent the rack from tipping over. See the documentation provided with the rack

cabinet for instructions on installing and anchoring the stabilizer feet.

Recommended Tools and Supplies

You may need the following items to install the system in a four-post rack cabinet:

• #2 Phillips screwdriver

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

8Four-Post Rack Installation

Sliding Rails Rack Kit Contents

• One pair of slide assemblies (convertible to RapidRails or VersaRails configuration)

• One cable-management arm

•Onetray

• One status indicator cable (if applicable)

• Tie wraps to secure the cables to the cable management arm

• Eight 10-32 x 0.5-inch flange-head Phillips screws (used in VersaRails configuration only)

NOTE: The nonmetric screws described in illustrations and in procedural steps are identified by size and number

of threads per inch. For example, a #10 Phillips-head screw with 32 threads per inch is identified as a 10-32 screw.

Figure 1-1. Sliding Rails Rack Kit Contents

1 tray 2 slide assemblies (2) 3 10-32 x 0.5-inch flange-head Phillips

screws (8) (VersaRails configuration only)

4 tie wraps 5 status indicator cable

(if applicable)

6 cable-management arm

Andere Handbücher für PowerEdge 1950

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell Wyse P25 Bedienungsanleitung

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell PowerEdge R630 Bedienungsanleitung

Dell

Dell EMC PowerEdge E45S Series Handbuch

Dell

Dell PowerEdge R810 Bedienungsanleitung

Dell

Dell PowerEdge M820 Systems Bedienungsanleitung

Dell

Dell D560 Bedienungsanleitung

Dell

Dell Wyse 5070 Extended Bedienungsanleitung

Dell

Dell PowerEdge R820 Kurzanleitung

Dell

Dell PowerEdge M710 Bedienungsanleitung

Dell

Dell EMC VxFlex Appliance R840 Bedienungsanleitung

Dell

Dell PowerEdge NX182 Bedienungsanleitung

Dell

Dell EMC VxFlex Ready Node 13G Handbuch

Dell

Dell EMC PowerEdge R450 12M1H Handbuch

Dell

Dell PowerEdge T320 Kurzanleitung

Dell

Dell EMC PowerEdge R7515 Bedienungsanleitung

Dell

Dell EMC PowerEdge T640 Bedienungsanleitung

Dell

Dell PowerEdge C6100 Bedienungsanleitung

Dell

Dell X95FF Handbuch

Dell

Dell PowerEdge T420 Kurzanleitung

Dell

Dell OptiPlex GX150 Bedienungsanleitung

Dell

Dell PowerEdge 6850 Benutzerhandbuch

Dell

Dell Poweredge el Bedienungsanleitung

Dell

Dell DX6004S Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch