Dell PowerEdge 2500 Bedienungsanleitung

www.dell.com

support.dell.com

Dell™ Systems

1 x 2 BACKPLANE KIT

INSTALLATION GUIDE

Notes, Notices, Cautions, and

Warnings

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate injury.

WARNING: A WARNING indicates a potentially hazardous

situation which, if not avoided, may result in severe injury.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer

Corporation is strictly forbidden.

Trademarks used in this text:

Dell

and the

DELL

logo are trademarks of Dell Computer

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any

proprietary interest in trademarks and trade names other than its own.

February 2001 P/N 9D082 Rev. A00

1 x 2 Backplane Kit Installation Guide 1-1

1 x 2 Backplane Installation

This document provides instructions for installing a 1 x 2 backplane kit to add provisions for

up to two additional 1-inch small computer system interface (SCSI) hard-disk drives in a

Dell™ system’s peripheral bay.

1 x 2 Backplane Kit Contents

The 1 x 2 backplane kit includes the following items:

• A 1 x 2 backplane attached to an assembled drive cage

• Four 6-32 x 0.25-inch hex-head Phillips screws

• Inter-integrated circuit (I2C) extension cable

• Nonterminated SCSI cable that links the 1 x 2 backplane to the system board

Before You Begin

WARNING: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, read the safety

precautions in your

System Information

document.

WARNING: Your system may have more than one power supply cable. To reduce

the risk of electrical shock, you must disconnect all power supply cables before

servicing the system. For more information, see “Safety First—For You and Your

Computer” in your

Installation and Troubleshooting Guide

1Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

CAUTION: See “Protecting Against Electrostatic Discharge” in the safety

instructions in your

System Information

document.

2Unpack the 1 x 2 backplane kit.

3Remove the front bezel (see “Removing the Front Bezel” in your Installation and

Troubleshooting Guide).

4Remove the system cover (see “Removing the System Cover” in your Installation and

Troubleshooting Guide).

NOTE: Verify that your system has the latest basic input/output system (BIOS)

revision and firmware. Download the latest revision from the Dell support site at

http://support.dell.com.

1-2 1 x 2 Backplane Kit Installation Guide

www.dell.com | support.dell.com

Removing the Peripheral Bay

1Remove the front fan assembly (see “Removing the Front Fan Assembly” in your

Installation and Troubleshooting Guide).

2Disconnect the interface cable from the interposer board attached to the back of the

CD-ROM/diskette drive.

3Loosen the thumbscrew securing the peripheral bay to the chassis (see Figure 1-1).

Figure 1-1. Removing the Peripheral Bay

removable

peripheral bay thumbscrew

1 x 2 Backplane Kit Installation Guide 1-3

4While grasping the peripheral bay handle, slide the peripheral bay backward and lift

the bay straight up to clear the chassis. Set the peripheral bay on a smooth work

surface.

5Facing the rear of the peripheral bay, reach inside the bay and press against the center

of the blank slot insert to release the insert. Remove both inserts.

Installing the Drive Cage

1Ensure that the 1 x 2 backplane is secured to the back of the drive cage with four

screws.

2Insert the drive cage into the peripheral drive bay until two of the holes on the top and

two holes on the bottom of the drive cage align with holes in the peripheral bay. See

Figure 1-2 for the orientation on a tower system.

NOTE: To install the drive cage into the peripheral bay of a

rack system

, turn the cage

180° so that the 1 x 2 backplane power connector is near the bottom of the peripheral bay.

NOTE: The drive cage can be inserted into the peripheral bay from the front or the back.

1-4 1 x 2 Backplane Kit Installation Guide

www.dell.com | support.dell.com

Figure 1-2. Installing the Drive Cage (Tower System)

3Secure the drive cage to the peripheral bay with four screws (two on the top and two

on the bottom).

Figure 1-2 shows the proper location for these screws.

Installing the Peripheral Bay

1Reconnect the interface cable to the CD-ROM/diskette drive interposer board.

2While grasping the peripheral bay handle, lower the peripheral bay into the chassis.

6-32 x 0.25-inch hex-

head Phillips screws (4)

1 x 2 Backplane Kit Installation Guide 1-5

3Align the tabs on side of the peripheral bay with the locking slots in the chassis and

slide the peripheral bay forward.

4Tighten the thumbscrew securing the peripheral bay to the chassis (see Figure 1-1).

Installing the I2C Extension Cable

1Disconnect the I2C cable connector at the 20-pin PLANAR connector on the system

board.

Do not disconnect the end that is connected to the SCSI backplane.

2In the customer kit, locate the I2C extension cable. This cable has three connectors: a

20-pin connector on one end, a 10-pin connector on the other end, and a 20-pin cable

connector in the middle (see Figure 1-3).

NOTE: Figure 1-3 shows the 1 x 2 backplane and its drive cage oriented for a tower

system. For rack systems, you must install the 1 x 2 backplane and its drive cage oriented

180° from the position shown in Figure 1-3.

Figure 1-3. Installing the I2CExtension Cable

10-pin I2C connector

nonterminated

SCSI cable

20-pin I2C connector

on system board

power connector

cooling shroud

cable clips

1-6 1 x 2 Backplane Kit Installation Guide

www.dell.com | support.dell.com

NOTICE: The I2C cable must be routed over the top of the cooling shroud.

3Route the I2C extension cable through the clips on the top of the cooling shroud (see

Figure 1-3).

4Attach the 10-pin connector on the I2C extension cable to the 10-pin connector

(PLANAR_1X2) on the 1 x 2 backplane.

5Attach the 20-pin connector on the end of the I2C extension cable to the 20-pin

connector on the system board (PLANAR).

6Attach the free end of the I2C cable, which was disconnected from the system board in

step 1, to the middle connector on the new I2C extension cable that you installed in

steps 3 and 4.

7Attach a four-wire power cable to the power connector (J1) on the 1 x 2 backplane (see

Figure 1-3).

NOTE: The four-wire power cable is the standard cable found on all systems and provides power

to peripherals, such as a tape drive.

Installing the SCSI Cable

NOTE: The SCSI cable installation described in this document is a typical installation of the

SCSI cable used with the 1 x 2 backplane. You can install the SCSI cable differently, depending

on redundant array of independent disks (RAID) configurations and the existence of SCSI

peripheral cards. Refer to your operating system documentation for information on how to set up

your SCSI devices.

To connect the SCSI cable to the 1 x 2 backplane, perform the following steps:

1In the customer kit, locate the nonterminated 68-pin SCSI cable. This cable has one

connector on one end and two connectors on the other end (see Figure 1-3).

2Route the SCSI cable through the clips on top of the cooling shroud (see Figure 1-3).

3On the end with two connectors:

aAttach the connector on the end of the cable to the vertical connector that is

closest to the 10-pin I2C connector on the 1 x 2 backplane (see Figure 1-3).

bAttach the next-to last connector on the cable to the remaining vertical connector

on the 1 x 2 backplane (see Figure 1-3).

4Attach the end with one connector to the SCSIB connector on the system board.

You can also connect this end of the cable to a Peripheral Component Interconnect

(PCI) SCSI or PCI RAID controller card.

1 x 2 Backplane Kit Installation Guide 1-7

Completing the Installation

1Replace the front fan assembly (see “Replacing the Front Fan Assembly” in your

Installation and Troubleshooting Guide).

2Replace the system cover (see “Replacing the System Cover” in your Installation and

Troubleshooting Guide).

3Replace the front bezel (see “Replacing the Front Bezel” in your Installation and

Troubleshooting Guide).

4Reconnect the system and peripherals to their power sources and turn on power.

1-8 1 x 2 Backplane Kit Installation Guide

www.dell.com | support.dell.com

Andere Handbücher für PowerEdge 2500

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell POWEREDGE 1900 Service-Handbuch

Dell

Dell PowerEdge 2550 Bedienungsanleitung

Dell

Dell DR4000 Restore Manager Bedienungsanleitung

Dell

Dell PowerEdge 2970 Bedienungsanleitung

Dell

Dell PowerEdge M620 Kurzanleitung

Dell

Dell PowerEdge 1850 Technisches Handbuch

Dell

Dell PowerEdge C6320 Bedienungsanleitung

Dell

Dell PowerEdge C5220 Bedienungsanleitung

Dell

Dell XC6320 Bedienungsanleitung

Dell

Dell PowerEdge R510 Kurzanleitung

Dell

Dell EMC PowerEdge T350 3RRTM Handbuch

Dell

Dell Wyse 3030 LT Bedienungsanleitung

Dell

Dell Precision FX100 Bedienungsanleitung

Dell

Dell PowerEdge 2450 Technisches Handbuch

Dell

Dell EMC XC Core XC750xa Handbuch

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell Wyse7020 Bedienungsanleitung

Dell

Dell POWEREDGE 1900 Bedienungsanleitung

Dell

Dell PowerEdge C6220 II Bedienungsanleitung

Dell

Dell PowerEdge 2650 Bedienungsanleitung

Dell

Dell PowerEdge R650XS RD8NP Handbuch

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell IP4700 Montage- und Wartungsanleitung

Dell

Dell PowerEdge C6100 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch