Dell PowerEdge 6800 Bedienungsanleitung

www.dell.com | support.dell.com

Dell™ Systems

Tower-to-Rack

Conversion Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, RapidRails, VersaRails, and the DELL logo are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

March 2005 P/N C8527 Rev. A01

Contents 3

Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installing the Tower-to-Rack Kit. . . . . . . . . . . . . . . . . . . . . . . . . . 7

Tower-to-Rack Kit Contents. . . . . . . . . . . . . . . . . . . . . . . . . . 8

Recommended Tools and Supplies . . . . . . . . . . . . . . . . . . . . . . 8

Conversion Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Removing the Optional Tower Bezel, Metal Feet, and Cover. . . . . . . . . 9

Removing the Control Panel Assembly and Tower Front Panel . . . . . . 11

Installing the Rack Front Panel and Control Panel Assembly . . . . . . . 13

Removing the Trim Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing the System in a Rack . . . . . . . . . . . . . . . . . . . . . . . 16

Installing the Optional Rack Bezel . . . . . . . . . . . . . . . . . . . . . 16

Figures

Figure 1-1. Tower-To-Rack Kit Contents . . . . . . . . . . . . . 8

Figure 1-2. Removing the Optional Tower Bezel . . . . . . . . . 9

Figure 1-3. Removing the Metal Feet . . . . . . . . . . . . . . . 10

Figure 1-4. Removing and Installing the Cover . . . . . . . . . . 11

Figure 1-5. Removing and Installing the Control Panel

Assembly and Front Panel . . . . . . . . . . . . . . 12

Figure 1-6. Replacing the Control Panel Assembly

Metal Bracket . . . . . . . . . . . . . . . . . . . . 14

Figure 1-7. Removing the Trim Panel . . . . . . . . . . . . . . . 15

Figure 1-8. Installing the Optional Rack Bezel . . . . . . . . . . 16

4Contents

Tower-to-Rack Conversion Guide 5

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect your

server, storage system, or appliance from potential damage. For complete safety and regulatory

information, see your

Product Information Guide

. Warranty information might be included within

this document or as a separate document.

Precautions for Rack-Mountable Products

Observe the following precautions for rack stability and safety. Also refer to the rack installation

documentation accompanying the system and the rack for specific warning and/or caution

statements and procedures.

Servers, storage systems, and appliances are considered to be components in a rack. Thus,

"component" refers to any server, storage system, or appliance, as well as to various peripherals or

supporting hardware.

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone (single)

racks or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly

before installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizer(s) before installing components in

the rack.

CAUTION: After installing system components in a rack, never pull more than one component out of

the rack on its slide assemblies at one time. The weight of more than one extended component could

cause the rack to tip over and injure someone.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a rack

cabinet using the customer rack kit when both the rack cabinet and rack kit were designed for your

system. The installation of your system and rack kit in any other rack cabinet has not been approved by

any safety agencies. It is your responsibility to have the final combination of system and rack kit in a

cabinet evaluated for suitability by a certified safety agency. The manufacturer disclaims all warranties

and liability in connection with such combinations.

• System rack kits are intended to be installed in an approved rack by trained service

technicians. If you install the kit in any other rack, be sure that the rack meets the

specifications.

CAUTION: Do not move large racks by yourself. Due to the height and weight of the rack, it is

recommended that a minimum of two people perform this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack, extend to

the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers

on a single rack or front stabilizers for joined multiple racks before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the rack.

• Use caution when pressing the component rail release latches and sliding a component into or

out of a rack; the slide rails can pinch your fingers.

6Tower-to-Rack Conversion Guide

www.dell.com | support.dell.com

• After a component is inserted into the rack, carefully extend the rail into a locking position,

and then slide the component into the rack.

• Do not overload the power supply branch circuit that provides power to the rack. The total

rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any system/component when servicing other systems/components

in a rack.

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or more

systems in an open-frame relay rack or in a rack cabinet. The Dell™ RapidRails™ rack kit can be

installed in all the manufacturer’s rack cabinets without tools, and the VersaRails™ rack kit can be

installed in most industry-standard rack cabinets. The procedures for installing both RapidRails

and VersaRails rack kits are similar. One rack kit is required for each system installed in the rack.

CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for

your Dell system. Using the rack kit for another system may result in damage to the system and personal

injury.

The RapidRails rack kit can be installed in any Dell rack cabinet and in most industry-standard rack

cabinets.

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that

meets the specifications of American National Standards Institute (ANSI)/Electronic Industries

Association (EIA) standard ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and

Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that is installed in a rack.

Before You Begin

Before you begin installing your system in the rack, carefully read "Safety Instructions," found

earlier in this guide, as well as the safety instructions found in your

Product Information Guide

for

additional information.

CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current

system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on the casters. The cabinet has no

brakes. Use extreme caution while moving the rack cabinet. Retract the leveling feet when relocating

the rack cabinet. Avoid long or steep inclines or ramps where loss of cabinet control may occur. Extend

the leveling feet for support and to prevent the cabinet from rolling.

Tower-to-Rack Conversion Guide 7

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect yourself as well as

others who may be involved. Your system may be very large and heavy, and proper preparation and

planning are important to prevent injury to yourself and to others. This becomes increasingly important

when systems are installed high up in the rack.

Rack Stabilizer Feet

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone (single)

racks or the front stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before

installing systems in a rack could cause the rack to tip over, potentially resulting in bodily injury under

certain circumstances. Therefore, always install the stabilizer(s) before installing components in the rack.

CAUTION: After installing systems in a rack, never pull more than one system out of the rack on its

slide assemblies at one time. The weight of more than one extended system could cause the rack to tip

over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system or other component is

pulled out of the rack with the slide assemblies fully extended. See the documentation provided

with the rack cabinet for instructions on installing and anchoring the stabilizer feet.

Installing the Tower-to-Rack Kit

CAUTION: The system may weigh up to 49 kilograms (108 pounds) when fully loaded. To prevent

personal injury, do not attempt to move the system by yourself.

8Tower-to-Rack Conversion Guide

www.dell.com | support.dell.com

Tower-to-Rack Kit Contents

The tower-to-rack kit includes the following items (see Figure 1-1):

• One rack front panel with rack handles and thumbscrews

• Twenty-one 6-32 x 0.312-inch black pan-head Torx screws

• Four 6-32 x 0.312-inch black flat-head Phillips screws

• Six shoulder mounting screws

• Replacement rack control-panel bracket

An optional rack bezel, complete with keylock and keys, is available separately.

Figure 1-1. Tower-To-Rack Kit Contents

Recommended Tools and Supplies

• #2 Phillips screwdriver

• 1/4-inch nut driver

• T-10 Torx driver (for removing and installing the front panels)

• T-15 Torx driver (for removing and installing the front panels)

Conversion Tasks

Installing a rack kit involves performing the following tasks:

• Removing the optional tower bezel, feet, and cover

• Removing the control panel assembly and tower front panel

• Installing the rack front panel and control panel assembly

• Removing the trim panel

• Installing the system in the rack

• Installing the optional rack bezel

rack front panel

rack control panel bracket

6-32 x 0.312 Torx

screws (21)

6-32 x 0.312

Torx screws (4)

shoulder mounting

screws (6)

Tower-to-Rack Conversion Guide 9

Removing the Optional Tower Bezel, Metal Feet, and Cover

To remove the tower bezel, orient the system as shown in Figure 1-2 and perform the

following steps:

Unlock the keylock. See Figure 1-2.

Rotate the keylock end of the bezel away from the front panel.

Unhook the other end of the bezel and pull the bezel away from the system.

Figure 1-2. Removing the Optional Tower Bezel

bezel

keylock

10 Tower-to-Rack Conversion Guide

www.dell.com | support.dell.com

Remove the four metal feet from the system:

Orient the system so that the metal feet hang over the edge of the table as shown in

Figure 1-3.

Using a #2 Phillips screwdriver or a 1/4-inch nut driver, remove the screw that secures

each metal foot and pull each foot from the chassis. See Figure 1-3.

Repeat this step for the other three metal feet.

Figure 1-3. Removing the Metal Feet

Remove the system cover and set it aside (see Figure 1-4):

Loosen the two thumbscrews on the front of the system.

Slide the system cover back and grasp the cover at both ends.

Carefully lift the cover away from the system and set it aside.

metal feet (4) hex-head Phillips

screws (4)

Andere Handbücher für PowerEdge 6800

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge M420 Kurzanleitung

Dell

Dell DX6000G Bedienungsanleitung

Dell

Dell POWEREDGE SC440 Bedienungsanleitung

Dell

Dell PowerVault LTO4-120HH Bedienungsanleitung

Dell

Dell PowerEdge R815 Bedienungsanleitung

Dell

Dell S5000 Series Bedienungs- und Montageanleitung

Dell

Dell PowerEdge MP148 Bedienungsanleitung

Dell

Dell External OEMR R910 Kurzanleitung

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell PowerEdge R610 Montageanleitung

Dell

Dell PowerEdge 2300 Bedienungsanleitung

Dell

Dell PowerEdge R430 Bedienungsanleitung

Dell

Dell PowerEdge R420xr Bedienungsanleitung

Dell

Dell PowerEdge 4200 Series Bedienungsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell PowerEdge T320 Kurzanleitung

Dell

Dell POWEREDGE R515 Bedienungsanleitung

Dell

Dell CX700 Bedienungsanleitung

Dell

Dell PowerEdge R620 Bedienungsanleitung

Dell

Dell PowerEdge R810 Stücklistenhandbuch

Dell

Dell PowerEdge NM176 Bedienungsanleitung

Dell

Dell PowerEdge M610 Kurzanleitung

Dell

Dell PowerEdge T110 II Kurzanleitung

Dell

Dell PowerEdge C5220 Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch