Dell PowerEdge systems 6300 Service-Handbuch

Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information1

'HOO3RZHU(GJHDQG

6\VWHPV[%DFNSODQH

,QVWDOODWLRQ,QIRUPDWLRQ

This document provides installation instructions for the optional 1 x 2 small computer

system interface (SCSI) backplane for the Dell PowerEdge 6300 and 4300 systems.

The 1 x 2 SCSI backplane provides hot-pluggable Ultra2/low voltage differential (LVD)

SCSI connections for two 1-inch hard-disk drives in the systems peripheral drive bay.

For a description of the SCSI backplanes functionality, see your systems Users

Guide and Installation and Troubleshooting Guide.

,QVWDOOLQJWKH[%DFNSODQH

:$51,1*7KHSRZHUVXSSOLHVLQWKLVFRPSXWHUV\VWHPSURGXFHKLJK

YROWDJHVDQGHQHUJ\KD]DUGVZKLFKFDQFDXVHERGLO\KDUP2QO\WUDLQHG

VHUYLFHWHFKQLFLDQVDUHDXWKRUL]HGWRUHPRYHWKHFRPSXWHUFRYHUDQG

DFFHVVDQ\RIWKHFRPSRQHQWVLQVLGHWKHFRPSXWHU

Your 1 x 2 backplane customer kit contains the following items:

Assembled drive cage

I2C extension cable

Nonterminated SCSI cable

%HIRUH<RX%HJLQ

:$51,1*<RXUV\VWHPPD\KDYHPRUHWKDQRQHSRZHUVXSSO\FDEOH7R

UHGXFHWKHULVNRIHOHFWULFDOVKRFNDWUDLQHGVHUYLFHWHFKQLFLDQPXVW

GLVFRQQHFWDOOSRZHUVXSSO\FDEOHVEHIRUHVHUYLFLQJWKHV\VWHP)RUPRUH

LQIRUPDWLRQVHH´6DIHW\)LUVW³)RU<RXDQG<RXU&RPSXWHUµLQ&KDSWHURI

WKH,QVWDOODWLRQDQG7URXEOHVKRRWLQJ*XLGH 

NOTES: Verify that your system has the latest basic input/output system (BIOS)

revision and firmware. Download the latest revision from the Support section of

the Dell Web site at http://www.dell.com.

2 Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information

For proper use of the 1 x 2 backplane, the minimum BIOS revision level for the 6300

system is A06, and the minimum BIOS revision level for the 4300 system is A05. To

ensure that you have the minimum firmware for the 1 x 2 backplane for both systems,

run the SMFLASH utility A33 on your system.

Before you install the 1 x 2 backplane, prepare the peripheral drive bay for installation.

To remove or install drives in the peripheral drive bay, you must remove the computer

cover and front bezel according to the instructions in Removing and Replacing the

Computer Cover in Chapter 7 of the Installation and Troubleshooting Guide .

5HPRYLQJDQG5HSODFLQJ)URQW3DQHO,QVHUWV

To protect the inside of the computer from foreign particles, a plastic front-panel

insert covers each empty peripheral drive bay. Before you install a drive in an empty

peripheral drive bay, you must first remove the front-panel insert.

Whenever you remove a drive, be sure to replace the front-panel insert over the

empty peripheral drive bay.

To remove the front-panel insert for a peripheral drive bay that you intend to use, first

remove the front bezel. Then, facing the inside of the front bezel, press against the

center of the insert with your thumbs until the insert bows sufficiently to loosen the

tabs on the sides of the insert. Pull the insert out of the bezel.

To replace a front-panel insert, position the insert over the peripheral drive bay

opening from the inside of the front bezel and carefully press the insert into place. A

tab on each side of the insert snaps into a corresponding latch on the inside of the

front bezel.

If you have any peripheral devices in the bottom two slots of the peripheral drive bay,

remove them before installing the 1 x 2 backplane. To remove an existing peripheral

device (such as a CD-ROM drive or a tape drive) from the peripheral drive bay, perform

the following steps:

1. Remove the system cover and the front bezel.

2. Locate the plastic clips attached to the drive rails that are on each side of the

peripheral device that you want to remove.

3. Squeeze the clips inward toward the device until the clips disengage from the

sides of the peripheral bay.

4. Pull the peripheral device outward until the device clears the peripheral bay.

5. Unplug the data cable and power cord from the back of the peripheral device. Do

not pull hard on the peripheral device when removing it from the system because

the cord and cable connections in the system may become loose or damaged.

NOTE: If a cord or cable prevents the removal of a peripheral device from the

system, unplug the cord or cable from the back of the peripheral device while it is

still in the peripheral bay.

Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information3

,QVWDOOLQJWKH'ULYH&DJH

To install the drive cage, perform the following steps:

1. Ensure that the drive cage is correctly assembled:

a. Verify that the 1 x 2 backplane is connected to the edge of the auxiliary SCSI

backplane via a 100-pin connector.

b. Verify that the auxiliary SCSI backplane is inserted into the enclosure on the

side of the cage and secured with one screw.

c. Verify that the 1 x 2 backplane is secured to the back of the cage with four

screws.

d. Verify that a drive rail is attached to each side of the drive cage.

2. Insert the drive cage into the empty peripheral drive bay until the clips on the

drive rails snap into the sides of the peripheral drive bay (see Figure 1).

)LJXUH,QVWDOOLQJWKH'ULYH&DJH

,QVWDOOLQJWKH,&([WHQVLRQ&DEOH

To i n s t a l l t h e I 2C extension cable, perform the following steps:

1. Disconnect the I2C cable from the 20-pin connector on the system board and set

it to one side (see Figure 2).

drive rail

clip

drive cage

4 Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information

2. In the customer kit, locate the I 2C extension cable. (This cable has three

connectors: a 20-pin connector on one end and in the middle and a 10-pin

connector on the other end.)

3. Attach the 10-pin connector on the I 2C extension cable to the 10-pin connector on

the 1 x 2 backplane.

4. Attach the 20-pin connector on the I 2C extension cable to the 20-pin connector

on the system board.

5. Attach the loose end of the I 2C cable, which was set aside, to the middle connec-

tor of the I2C extension cable.

6. Attach a four-wire power cable to the power connector on the 1 x 2 backplane.

NOTE: The four-wire power cable is the standard cable found on all systems and

provides power to peripherals; for example, for a CD-ROM drive or tape drive.

)LJXUH,QVWDOOLQJWKH, &([WHQVLRQ&DEOH

10-pin connector on

1 x 2 backplane

I2C extension cable

hard-disk drive

SCSI backplane

I2C cable

20-pin connector

on system board

power connector

Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information5

,QVWDOOLQJWKH6&6,&DEOH

NOTE: The SCSI cable installation described in this document is a typical installation

of the SCSI cable used with the 1 x 2 backplane. You can install the SCSI cable

differently, depending on redundant arrays of independent disks (RAID) configurations

and the existence of SCSI peripheral cards. Refer to your operating system documen-

tation for information on how to set up your SCSI devices.

To install the SCSI cable to the 1 x 2 backplane, perform the following steps:

1. In the customer kit, locate the nonterminated 68-pin SCSI cable. (This cable has

two connectors at one end and one connector on the other end. See Figure 3.)

)LJXUH,QVWDOOLQJWKH6&6,&DEOHWR[%DFNSODQH

top drive connector

bottom drive

connector

SCSI cable

SCSI controller

on system board

6 Dell PowerEdge 6300 and 4300 Systems 1 x 2 Backplane Installation Information

2. On the end with two connectors:

a. Attach the connector at the end of the cable to the bottom drive connector

on the 1 x 2 backplane.

b. Attach the second connector to the top drive connector on the 1 x 2

backplane.

3. Attach the end with one connector to a SCSI controller on the system board.

&RQYHUWLQJWKH'ULYH&DUULHUV

You can use only 1-inch hard-disk drives with the 1 x 2 backplane. If you have 1.6-inch

hard-disk drive carriers that you want to use with your 1 x 2 backplane, you need to

place 1-inch hard-disk drives in the carrier and modify the 1.6-inch carriers to be 1 inch

in width. To modify the 1.6-inch carriers to 1-inch width, remove the spacer insert.

NOTE: To remove the spacer insert, use a screwdriver to pry open the clips on the

inside of the carrier release handle, and pull the spacer insert away from the carrier.

After you have installed your 1 x 2 backplane, see Installing and Removing SCSI

Hard-Disk Drives in Chapter 10 of the Installation and Troubleshooting Guide for

information on how to install your hard-disk drives.

NOTE: The 1 x 2 backplane sets the top drive to SCSI ID0 and the bottom drive to

SCSI ID1.

Andere Handbücher für PowerEdge systems 6300

Dieses Handbuch passt für folgende Modelle

Andere Dell Server Handbücher

Dell

Dell POWEREDGE SC440 Bedienungsanleitung

Dell

Dell PowerEdge 1600SC Bedienungsanleitung

Dell

Dell PowerEdge E04S001 Bedienungsanleitung

Dell

Dell Active Fabric Manager Kurzanleitung

Dell

Dell PowerEdge R210 II Bedienungsanleitung

Dell

Dell 6100 Bedienungsanleitung

Dell

Dell OptiPlex FX130 Bedienungsanleitung

Dell

Dell PowerEdge R900 Bedienungsanleitung

Dell

Dell PowerEdge 1850 Technisches Handbuch

Dell

Dell PowerEdge 2950 Bedienungsanleitung

Dell

Dell EMC PowerEdge T640 D24XR Handbuch

Dell

Dell PowerEdge R530xd Bedienungsanleitung

Dell

Dell EMC PowerEdge R440 Handbuch

Dell

Dell KGR3H Handbuch

Dell

Dell PowerEdge 350 Bedienungsanleitung

Dell

Dell PowerEdge MX760c Handbuch

Dell

Dell Wyse 5040 AIO Bedienungsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell EMC E39S Series Handbuch

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell PowerEdge R530 Bedienungsanleitung

Dell

Dell EMC XC Core XC650 Handbuch

Dell

Dell EMC VxFlex Ready Node 13G Handbuch

Dell

Dell PowerEdge 2410 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch