3Please read this instruction carefully before use.
3DOP series Extension Digital I/O Module should be used with DOP-AE series HMI product. Ensure to
switch off the power before wiring.
3Please install this DOP series Extension Digital I/O Module in an enclosure free of airborne dust,
humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from
operating the device (e.g. key or specific tools are required for opening the enclosure) in case danger
and damage on the device may occur.
3DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may
occur. Check all the wiring again before switching on the power.
3DO NOT touch any internal circuit in 1 minute after the power is switched off. Do NOT touch any
terminal when the power is switched on.
3Make sure the ground terminal is correctly grounded in order to prevent electromagnetic
interference.
3DO NOT place any heavy objects on the connection port of DOP series Extension Digital I/O Module.
Doing so may damage the product.
XIntroduction
1.1 Model Explanation
DOP - EXIO 14 R AE
(1) (2) (3) (4) (5)
(1) Product Name DOP: Delta Operation Panel
(2) Series EXIO: Extension Digital I/O
(3) Input / Output Point 14: 8 input points / 6 output points
28: 16 input points / 12 output points
(4) Output Contact Type R: Relay
(5) Applicable HMI Series AE: DOP-AE Series HMI
1.2 Product Outline
1. Connection Port
2. Direct Mounting Hole
3. Input / Output Terminals
4. Nameplate
1.3 Model Name
Input / Output
Input Unit Output Unit
Model Name Power Point Type Point Typ e
DOP-EXIO14RAE 8 6 Relay
DOP-EXIO28RAE 5VDC,
supplied
by HMI
16
DC Type
Sink or
Source 12 Relay
YFunction Specifications
Item Specifications Remark
Control Method Stored program, cyclic scan system -
I/O Processing Method Batch I/O (refresh) Immediate refresh command available
only with I/O of the MPU
Execution Speed Basic command (average approx. 30
us)
Application command (30 ~ hundreds
us)
Program Language Commands + Ladder Diagram +
SFC Step commands included
Item Specifications Remark
Program Capacity 999 Steps Built-in EEPROM
Commands Basic commands: 32 (including the
STL commands) Application commands: 59
Step Relay
(Latched)
General
Step Point 128 Points S10 ~ S127
General 1280 Points M0 ~ M511, M768 ~ M999, 744 points;
M1000 ~ M1279, 280 points*1
Auxiliary
Relay Latched 256 Points M512 ~ M767
64 Points T0~T63 (100 ms time base)
63 Points T64~T126 (10 ms time base)
Timer Digital
1 Points T127 (1 ms time base)
General 112 Points C0 ~ C111
Latched 16 Points C112 ~ C127
Counter
32bit 13 Points
C235,C236,C237,C238,C241,C242,
C244,C246,C247,C249,C251,C252,
C254 (all of them are latched type)
General 408 Points D0 ~ D407
Data Register Latched 192 Points D408 ~ D599
Pointer P 64 Points P0 ~ P63
Index
Register E / F 2 E, F
Decimal K 16bit: -32768 ~ +32767 32bit: -2147483648 ~ +2147483647
Constant Hexadecim
al H 16bit: 0000 ~ FFFF 32bit: 00000000 ~ FFFFFFFF
Self Diagnosis / Protection I/O check, system execution timeout check, invalid command check, program
check and password settings
Monitor / Debug Program execution time display, bit / word, device settings
*1: M1000, M1001, M1002, M1003, M1020, M1021, M1022, M1067, M10068, and M1161 are the special auxiliary relays (special M).
ZElectrical Specifications
Item / Model Name DOP-EXIO14RAE DOP-EXIO28RAE
Power Supply Voltage 5VDC, 1A (supplied by HMI)
Power Consumption 0.25W 0.5W
Noise Immunity
RS: Frequency: 80MHz ~ 1GHz, 1.4GHz ~ 2.0GHz, Test level 10V/m
CS: Frequency: 0.15MHz ~ 80MHz, Test level 10V (HMI power port & I/O line)
ESD: Air discharge ±8KV
EFT: ±1.5KV (HMI power port)
±1KV (I/O line)
Surge: ±2KV (HMI power port)
Ambient Temperature /
Humidity
Operation: 0°C ~ 50°C (Temperature), 10 ~ 90% (Humidity),
Storage: -40°C ~ 85°C (Temperature), 10 ~ 90% (Humidity)
Vibration / Shock
IEC 61131-2 Compliant
5Hz≦f＜9Hz = Continuous: 1.75mm / Occasional: 3.5mm
9Hz≦f≦150Hz = Continuous: 0.5g / Occasional: 1.0g
X, Y, Z directions for 10 times
Weight Approx. 95.5g Approx. 116g
Input Point Electric Specifications
Input Type DC (SINK or SOURCE)
Input Voltage 24VDC (5mA)
Off→On, above 16VDC
Active Level On→Off, below 14.4VDC
Response Time Approx. 10ms
Output Point Electric Specifications
Output Type Relay-R
Current Specifications 1.5A / 1 Point (5A/COM)
Voltage Specifications 250VAC, below 30VDC
75VA (Inductive)
Maximum Loading 90 W (Resistive)
Response Time Approx. 10 ms
Mechanical Life 2 × 107times (without load)
Electrical Life 100,000 times (3A 250VAC/30VDC)
6,000 times (5A 250VAC/30VDC)
[Installation & Wiring
4.1 Wiring
22-16AWG
< 1.5m m
1. Please use the 28-16 AWG (1.5mm
2
) single-core bare wire (Solid type) or
the multi-core wire (Stranded type) for the I/O wiring. The stripped length of
the wire should be 6-7mm, and the torque specification of the screw for the
terminal is 4.5lb-in. Please refer to the specifications of the terminal shown
in the figure on the left.
2. DO NOT place the I/O signal wires and power supply wire in the same
wiring duct.
4.2 Caution
Environment
1. DO NOT install the Extension Digital I/O Module in a place subjected to corrosive or flammable gases,
liquids, or airborne dust or metallic particles.
2. DO NOT install the Extension Digital I/O Module in a location high temperature and high humidity (where
temperature and humidity will exceed specification).
3. DO NOT install the Extension Digital I/O Module in a location where vibration and shock will exceed
specification.
Wiring Note
1. Please avoid any conductive debris and tiny metal materials enter the Extension Digital I/O Module when
screwing and wiring.
2. Allow a minimum space of 50mm between the Extension Digital I/O Module and other control devices, and
keep the Extension Digital I/O Module away from the high-voltage lines or any power equipment.
4.3 Terminal Identification
4.4 Wiring
There are two types of DC inputs, SINK and SOURCE, and they are defined as follows:
Sink = (common port for current input S/S) Source = (common port for current output S/S)
Input Point Wiring (S/S shown in the wiring diagrams indicates SS1 or SS2 contact)
DC Signal IN Input point loop equivalent circuit Wiring loop
SINK mode
DC Signal IN Input point loop equivalent circuit Wiring loop
SOURCE mode
Output Point Wiring
Be careful with the connection of the common terminals
when wiring outputs. For example, when wiring
DOP-EXIO14RAE (DOP-EXIO28RAE), output terminal
Y0 (Y10) uses C0 (C10), Y1 (Y11) uses C1 (C11), Y2 ~
Y3 (Y12 ~ Y13) uses C3 (C13), Y4 ~ Y5 (Y14 ~ Y15)
uses C5 (C15), as shown below:
NOTE
1) The content of this instruction sheet may be revised without prior notice. Please consult our distributors or download the most
updated version at http://www.delta.com.tw/industrialautomation.
http://www.delta.com.tw/industri alautomation/
Extension Digital I/O Module
Instruction Sheet
Warning
1
2
3
4
