Delta Electronics LCP-200A4HSR Bedienungsanleitung

DELTA ELECTRONICS, INC.

1 Aug., 2006

Rev. 0A

www.deltaww.com

RoHS Compliant Small Form Factor Pluggable Transceiver RoHS

Compliant for ESCON, Fast Ethernet, ATM, SONET OC-3/SDH STM-1

FEATURES

 Compliant with SFP Transceiver MSA

specification

 Compliant with Industry Standard RFT

Electrical Connector and Cage

 1310nm LED Source Technology

 Single + 3.3V Power Supply and TTL Logic

Interface

 EEPROM with Serial ID Functionality

 Laser Class 1 Product which comply with the

requirements of IEC 60825-1 and IEC 60825-2

 Duplex LC Connector interface

Description

The LCP-200A4HSR is a hot pluggable 3.3V

Small-Form-Factor transceiver module designed

expressly for high-speed communication

applications that require rates of up to

200Mbit/sec. It is compliant with the SFP

Multi-source Agreement.

The LCP-200A4HSR transceivers provide with

the LC receptacle that is compatible with the

industry standard LC connector. The transceiver

is also compatible with industry standard RFT

connector and cage.

The transmitter section consists of a 1310nm

LED in an optical subassembly (OSA) while the

receiver consists of InGaAs PIN photodiode

mounted together with a trans-impedance

preamplifier. The post-amplifier also includes a

LOS (Loss Of Signal) circuit that provides a TTL

logic-high output when an unusable optical

signal level is detected.

The LCP-200A4HSR transceiver is a Class 1

eye safety product. The optical power levels,

under normal operation, are at eye safe level.

Applications

 ESCON

 SONET OC-3/SDH STM-1

 ATM Network

 Fast Ethernet

 Switch to Switch interface

 Switched backplane applications

 File server interface

 Data Link up to 2km in 62.5/125um Multi Mode

Fiber

DELTA ELECTRONICS, INC.

2 Aug., 2006

Rev. 0A

www.deltaww.com

Absolute Maximum Ratings

Parameter Symbol Min. Typ. Max. Unit Note

Storage Temperature Ts -40 85 ºC

Supply Voltage VCC 0 5 V

Recommended Operating Conditions

Parameter Symbol Min. Typ. Max. Unit Note

Case Operating Temperature TC-5 70 ºC 1

Supply Voltage VCC 3.135 3.465 V

Note 1: See order information

Electrical Characteristics

(VCC=3.135V to 3.465V)

Parameter Symbol Min. Typ. Max. Unit Note

Total Supply Current ICCT 300 mA

Transmitter

Transmitter Differential Input Voltage VDT 0.5 2.4 V 1

Transmitter Disable Input-High VDISH 2 VCC+0.3 V

Transmitter Disable Input-Low VDISL 0 0.8 V

Transmitter Fault Output-High VTXFH 2 VCC+0.3 V 2

Transmitter Fault Output-Low VTXFL 0 0.8 V 2

Receiver

Receiver Differential Output Voltage VDR 0.35 2 V 3

LOS Output Voltage-High VLOSH 2 VCC+0.3 V 1

LOS Output Voltage-Low VLOSL 0 0.8 V 1

Output Data rise time/ fall time tr/tf1.5 ns 4

Notes

1. Internally AC coupled and terminated to 100 Ohm differential load.

2. Pull up to VCC with a 4.7K – 10Kresistor on host Board

3. Internally AC coupled, but requires a 100 Ohm differential termination at or internal to Serializer/

Deserializer.

4. These are 20%~80% values.

DELTA ELECTRONICS, INC.

3 Aug., 2006

Rev. 0A

www.deltaww.com

Optical Characteristics

(VCC=3.135V to 3.465V, Data Rate=200Mb/sec, PRBS=223-1 NRZ, 62.5/125um MMF)

Parameter Symbol Min. Typ. Max. Unit Note

Transmitter

Output Optical Power (Avg.) PO-20 -14

dBm

Optical Extinction Ratio 9 dB

Center Wavelength λC1310 nm

Spectral Width (RMS) σ

200 nm

Optical rise time/ fall time tr/tf3 ns 1

Relative Intensity Noise RIN -117 dB/Hz

Receiver

Sensitivity (Avg.) PIN -31

dBm 2

Input Optical Wavelength λ1100 1310 1600 nm

LOS-Deasserted (Avg.) PA

-31 dBm

LOS-Asserted (Avg.) PD-48 dBm

LOS-Hysteresis PA-PD0.5 dB

Overload PO-14 dBm

Notes:

1. These are unfiltered 10%~90% values

2. The sensitivity is provided at a BER of 1×10-10 or better with an input signal consisting of 200Mb/s,

223-1 PRBS and ER=9dB.

DELTA ELECTRONICS, INC.

4 Aug., 2006

Rev. 0A

www.deltaww.com

SFP Transceiver Electrical Pad Layout

Pin Function Definitions

Pin Num. Name Function Plug Seq. Notes

1 VeeT Transmitter Ground 1

2 TX Fault Transmitter Fault Indication 3 Note 1

3 TX Disable Transmitter Disable 3 Note 2

Module disables on high or open

4 MOD-DEF2 Module Definition 2 3 Note 3, 2 wire serial ID interface

5 MOD-DEF1 Module Definition 1 3 Note 3, 2 wire serial ID interface

6 MOD-DEF0 Module Definition 0 3 Note 3, Grounded in Module

7 Rate Select Not Connect 3 Function not available

8 LOS Loss of Signal 3 Note 4

9 VeeR Receiver Ground 1 Note 5

10 VeeR Receiver Ground 1 Note 5

11 VeeR Receiver Ground 1 Note 5

12 RD- Inv. Received Data Out 3 Note 6

13 RD+ Received Data Out 3 Note 7

14 VeeR Receiver Ground 1 Note 5

15 VccR Receiver Power 2 3.3 ± 10%, Note 7

16 VccT Transmitter Power 2 3.3 ± 10%, Note 7

17 VeeT Transmitter Ground 1 Note 5

18 TD+ Transmit Data In 3 Note 8

19 TD- Inv. Transmit Data In 3 Note 8

20 VeeT Transmitter Ground 1 Note 5

Plug Seq.: Pin engagement sequence during hot plugging.

DELTA ELECTRONICS, INC.

5 Aug., 2006

Rev. 0A

www.deltaww.com

Notes:

1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10Kresistor on the host

board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind.

Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module

with a 4.7 – 10 K resistor. Its states are:

Low (0 – 0.8V): Transmitter on

(>0.8, < 2.0V): Undefined

High (2.0 – 3.465V): Transmitter Disabled

Open: Transmitter Disabled

3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10Kresistor on the

host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def 0 is grounded

by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for

serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID

4) LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10Kresistor.

Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is

below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In

the low state, the output will be pulled to < 0.8V.

5) VeeR and VeeT may be internally connected within the SFP module.

6) RD-/+: These are the differential receiver outputs. They are AC coupled 100differential lines which should be

terminated with 100(differential) at the user SERDES. The AC coupling is done inside the module and is thus

not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential

(185 – 1000 mV single ended) when properly terminated.

7) VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±10% at the SFP

connector pin. Maximum supply current is 300 mA. Recommended host board power supply filtering is shown

below. Inductors with DC resistance of less than 1 ohm should be used in order to maintain the required voltage

at the SFP input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot

plugging of the SFP transceiver module will result in an inrush current of no more than 30 mA greater than the

steady state value. VccR and VccT may be internally connected within the SFP transceiver module.

8) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 

differential termination inside the module. The AC coupling is done inside the module and is thus not

required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200

mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 –

600 mV single-ended) be used for best EMI performance.

DELTA ELECTRONICS, INC.

6 Aug., 2006

Rev. 0A

www.deltaww.com

Recommend Circuit Schematic

Laser Diode

Photo Diode

1uH

0.1uF10uF

0.1uF

0.01uF

0.1uF10uF

RES1

100 Ohms*

RES1 RES1 RES1

10k Ohms

100 Ohms

VCC

Protocol Vcc

SerDes ICProtocol IC

PLD / PAL Mod_def 2

Mod_def 1

Mod_def 0

3.3V

DELTA SFP Module

Preamp &

Tx_Disable

Quantizer

Tx_Fault

TD +

TD -

VeeT

RD +

RD -

Rx_LOS

VeeR

Tx_Disable

Rx_LOS

RES1 = 4.7k to 10k Ohms

VccT

VccR

Laser Driver

* Depands on SerDes IC used

EEPROM

DELTA ELECTRONICS, INC.

7 Aug., 2006

Rev. 0A

www.deltaww.com

Package Outline Drawing for Metal Housing with Bail de-latch

DELTA ELECTRONICS, INC.

8 Aug., 2006

Rev. 0A

www.deltaww.com

SFP timing parameters for SFP management

Parameter Symbol Min. Max. Unit Unit Conditions

TX_DISABLE Assert

time t_off 10

µsec

Time from rising edge of TX_DISABLE to

when the optical output falls below 10% of

nominal

TX_DISABLE

Negate time t_on 1 msec

Time from falling edge of TX_DISABLE to

when the modulated optical output rises

above 90% of nominal

Time to initialize,

including reset of

TX_FAULT

t_init 300 msec From power on or negation of TX_Fault using

TX Disable.

TX Fault Assert

Time

t_fault

100 µsec Time from fault to TX fault on.

TX_DISABLE to

reset t_rest 10

µsec Time TX Disbale must be held high to reset

TX_Fault

LOS Assert Time t_loss_on 100 µsec Time from LOS state to Rx LOS assert

LOS Deassert Time t_loss_off 100 µsec Time from non-LOS state to Rx LOS deassert

Serial ID Clock Rate f_serial_clock 100 kHz

LCP-200A4HSR EEPROM Serial ID Memory Contents (2-Wire Address A0h)

Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII

00 03 25 20 50 53 S 75 SN 100 00 125 00

01 04 26 20 51 52 R 76 SN 101 00 126 00

02 07 27 20 52 20 77 SN 102 00 127 00

03 00 28 20 53 20 78 SN 103 00

04 80 29 20 54 20 79 SN 104 00

05 00 30 20 55 20 80 SN 105 00

06 00 31 20 56 30 81 SN 106 00

07 00 32 20 57 30 82 SN 107 00

08 00 33 20 58 30 83 SN 108 00

09 00 34 20 59 30 84 DC Note 3 109 00

10 00 35 20 60 05 85 DC 110 00

11 00 36 00 61 1E 86 DC 111 00

12 02 37 00 62 00 87 DC 112 00

13 00 38 00 63 CS1 Note 1 88 DC 113 00

14 00 39 00 64 00 89 DC 114 00

15 00 40 4C L 65 1A 90 DC 115 00

16 00 41 43 C 66 05 91 DC 116 00

17 C8 42 50 P 67 05 92 00 117 00

18 00 43 2D - 68 SN Note 2 93 00 118 00

19 00 44 32 2 69 SN 94 00 119 00

20 44 D 45 30 0 70 SN 95 CS2 Note 4 120 00

21 45 E 46 30 0 71 SN 96 00 121 00

22 4C L 47 41 A 72 SN 97 00 122 00

23 54 T 48 34 4 73 SN 98 00 123 00

24 41 A 49 48 H 74 SN 99 00 124 00

Notes:

1) Byte 63(CS1): Check sum of bytes 0-62.

2) Byte 68-83 (SN): Serial number.

3) Byte 84-91 (DC): Date code.

4) Byte 95 (CS2): Check sum of bytes 64-94.

5) Bytes 128-255 had been set hex. 00.

DELTA ELECTRONICS, INC.

9 Aug., 2006

Rev. 0A

www.deltaww.com

Regulatory Compliance

Feature Reference Performance

Electromagnetic Interference

(EMI) FCC Class B

EN 55022 Class B (CISPR 22A)

Radio Frequency

Electromagnetic Field

EN 61000-4-3

IEC 1000-4-3

Electrostatic Discharge to the

Duplex LC Receptacle

EN 61000-4-2

IEC 1000-4-2

IEC 801.2

Electrostatic Discharge to the

Electrical Pins MIL-STD-883E Method 3015.7

(1) Satisfied with electrical

characteristics of product

spec.

(2) No physical damage

Eye Safety US FDA CDRH AEL Class 1

EN 60950: 2000

EN 60825-1: 1994+A11+A2

EN 60825-2: 2000

CDRH File # 0321539-00

TUV Certificate No. R50032471

Component Recognition Underwriters Laboratories and

Canadian Standards Association Joint

Component Recognition for Information

Technology Equipment Including

Electrical Business Equipment

UL File # E239394

Ordering information for SFP modules

LCP-200X1X2X3X4X5X6

X1: Fiber

A: Multi-mode 1310nm

X4: Digital Diagnostic Function

S: Without digital diagnostic function

X2: Power Supply Voltage and SD Level

4: 3.3V, TTL SD Level

X5: Housing Type

R: RoHS compliant

X3: Distance

H: 2km

X6: Temperature

Blank: -5 to +70 degree C

H: -10 to +85 degree C

T: -40 to +85 degree C

Inhaltsverzeichnis

Andere Delta Electronics Transceiver Handbücher

Delta Electronics

Delta Electronics LCP-1250RJ3SR-L Bedienungsanleitung

Delta Electronics

Delta Electronics 10GBASE-SR SFP+ Optical Transceiver... Bedienungsanleitung

Delta Electronics

Delta Electronics Optical Transceiver Modules OPT-155Axxxx Bedienungsanleitung

Delta Electronics

Delta Electronics LCP-1250RJ3SR-S Bedienungsanleitung

Delta Electronics

Delta Electronics GBIC-1250B5LR Bedienungsanleitung

Delta Electronics

Delta Electronics SFP Bi-Directional Transceiver Module... Bedienungsanleitung

Delta Electronics

Delta Electronics Multimode SFP Transceiver LCP-1250A4FDRx Bedienungsanleitung

Delta Electronics

Delta Electronics SPBD-1250B4Q1RT Bedienungsanleitung

Delta Electronics

Delta Electronics LCP-4250A4CDR Series Bedienungsanleitung

Delta Electronics

Delta Electronics Optical Transceiver Modules OPT-622A1F1R Bedienungsanleitung

Delta Electronics

Delta Electronics Sonet OC-48/SDH Bedienungsanleitung

Delta Electronics

Delta Electronics Multi-Rate CWDM SFP Transceiver LCP-1250... Bedienungsanleitung

Delta Electronics

Delta Electronics SFP Transceiver LCP-2488B4HDRx Bedienungsanleitung

Delta Electronics

Delta Electronics Single Mode SFP Transceiver LCP-1250B4QDRx Bedienungsanleitung

Delta Electronics

Delta Electronics LCP-155A4HSRx Series Bedienungsanleitung

Delta Electronics

Delta Electronics LCP-155B4JSRx Series Bedienungsanleitung

Delta Electronics

Delta Electronics LCP-155A4HSRBx Series Bedienungsanleitung

Delta Electronics

Delta Electronics OPT-1250xxxx Series Bedienungsanleitung

Delta Electronics

Delta Electronics SFP Bi-Directional Transceiver Module... Bedienungsanleitung

Delta Electronics

Delta Electronics SFBD-1250B4Q1R Bedienungsanleitung

Delta Electronics

Delta Electronics LCP-155B4MSRx Series Bedienungsanleitung

Delta Electronics

Delta Electronics SFBD-1250A4Q1R Bedienungsanleitung

Delta Electronics

Delta Electronics Single Mode SFP Transceiver LCP-1250B4MDRx Bedienungsanleitung

Delta Electronics

Delta Electronics SPBD-1250A4Q1RT Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung