【Wiring diagram –Connect the equipment via RS485】
Connect A1 and B1 with the equipment’s A and B, the recommended wire to use is 22AWG Shielded Foil
Twisted-Pair (SFTP)
Power onverification
‧After the product has been installed, the power indicator lights up after the power is connected, and the air
quality indicator turns blue, which means the device is turning on at this time. If green or yellow appears, it
means that the device has completed booting and the current air quality status is displayed. If the power
indicatordoes not light up, pleaseverify that the power cord is properly connected and that there is a
supply of power.
‧Wireless model has Bluetooth and Wi-Fi functionality. Users can go to the iPhone app store or Android play
store to download the APP.
【Installation guide】
Installation steps
‧The product is recommended to be installed at a height of 80-150 cm (31.5-59 inches).
‧Use the wall mount included in the box to install it on the wall, or install in a power box. The wall mount has
screw hole spacing (60mm and 84mm) suitable for power boxes in multiple countries, but the power box
must be installed horizontally as shown in Figure 1.
‧Verify that the power supply and data lines are laid out according to specifications before installation
‧As shown in Figure 2, install it on the wallmount and verify that all four buckles are installed and fixed.
‧As shown in Figure 3, usea hexagonal screwdriver to fasten the M4 hex socket screws to complete the installation
【Note】Power source notice
This product uses a 9-24V DC power supply. AC power must be converted to the required power source or
use the specified power adapter . The output voltage Vout is the same with input voltage Vin. Output
voltage should be 12V when using a 12V power adapter.
Fig 1. Fig2. Fig 3.
Do not inject contaminants
Do not directly inject contaminants containing gases or particulate matter. Exposure to excessive
contaminants can permanently damage the sensor.
Do not repair this product yourself
The product does not have components that users can repair themselves. Do not attempt to open it. Once the
warranty sticker breaks, the warranty is void.
【Note】Do not insert objects through the vents, which may be dangerous and damaging.
Cleaning the exterior of UNOnext
To clean the product, unplug the power cord and all wiring.
Wipe with a soft, cotton-free cloth. Avoid moisture at any openingson the device body. Please do not spray
liquids directly onto it.
Prohibit live line operation
When the installer configures DIP switches and terminal connector, be sure to power off before execution
and then power on after.
‧In RS485 control mode, if the equipment is successfully connected, the equipment status indicator is
static on/off . If it is not correctly connected, the equipment status indicator will keep blinking.
‧The installer can verify ventilation volume by switching to manual mode and corresponding fan speed.
‧After a period, the health of the filter will return to zero. At this time, it is recommended to replace the filter.
After the replacement, you can press and hold the filter reset button on the back of the product toreset.
DIP switches
1 2 3 4 5 6 7 8
Enable smart control function
‧Turn all the DIP switches up, press the multi-func. button then power on, release the button after the filter
health LED blinks, and confirm that the screen has changed successfully after restarting, and then restore the
DIP switches as previously stated.
【Wiring diagram –Connect the equipment via digital output】
【Note】
To connect multiple equipment, you must set different Modbus slave address. Please reference the
user manual of that equipment to config slave address.
Connect multiple equipment
‧The product can connect to the 4 same equipment via RS485 in series through daisy chain - linear
topology. At this time, each device will follow the same control mode and fan speed level.
Wiringdiagram Fan speedlevels Controlinterface
12V GND BA
6 7
Unlimited 1level
6 7
3levels
6 7
2levels
6 7 8
RS485
Delta ERV“VEB250AT3”
Dipswitches
1110 12 13
B1 A1 Vin 14
Vout
65 789
21 34B2 A2
NO2 NO1
NO3
NO4
AI2
AI1
GND
Low fan
speed
Medium fan
speed
High fan
speed
NO4
COM
NC C NO
12VDC
AC250V +
-
Relay
+
-
Relay
ON/OFF NO1
COM
【Place of origin】
This product is made in Taiwan. The place of origin is No. 256, Yangguang St., Neihu Dist., Taipei City,
Taiwan (R.O.C.).
【APP and website links】
The product is equipped with wireless technology and can use an APP and website to monitor the air
quality status, which can be obtained using the following QR codes. (For the wireless model only). Please
go to the official website to learn about how to use the product.
iOSAPP AndroidAPP UNOweb Doc. &Resources
1 level output (ON/OFF)
3 level output (FAN speed)
12VDC
AC250V
or/and
【Note】
•DIP switches pin8 should be turned ON
•External relay requirement : AC250V resistive, and 12VDC SPDT, 15A
Using right connectors and ports
‧Do not force the connector into the port. Check the port for foreign objects. If the connectors and ports
do not fit easily, it may be because they do not match each other. Make sure that the connector
matches the port, and that the connector is aligned to the correct location corresponding to the port.
‧Insert the wrong pin may result in damage to the product, it will not be responsible for the product
warranty.
+
12VDC
AC250V
+
12VDC
AC250V
NO3
NO2
COM
COM
-
-
5
6
4
(depend on equipment)
【Note】Not following instructions may result in damage to the product or other items.
【Note 】
The product supports control of energy recovery ventilation and inline fan. Regarding the compatibility
of equipment brands and models, please contact your dealer and local sales for technical evaluation
before purchasing. No matter RS485 or digital output, control logic is fixed for smart ventilation
control, PLEASE DON’T TO USE FOR OTHER APPLICATIONS
0 - 100 ug/m3±25 ug/m3
100 - 1000 ug/m3±25%
0 - 100 ug/m3±10 ug/m3
100 -1000 ug/m3±10%
±30 ppm ±3%
Measurement Range Accuracy
0.5-10 ppm
Wall mount, NTC thermistor (Optional)
Connectivity
0.01 ppm
±20 ppm or ±5%
±15% at 20~50 ºC
±15% in lab test (Ethanol)
±0.3 ºC at 25 ºC and 50% rH
±5% at 25 ºC and 50% rH
±1ºC at 25 ºC and 50% rH
For background ambient
light reference
0-30000 ppb
0-5000 ppb
0-10000 lux
0-1000 ug/m3
0-1000 ug/m3
0-500 ppm
400-10000 ppm
0-100% rH
0 -50 ºC
NTC10k Thermistor
