Shure MXA710 Series Bedienungsanleitung

MXA710

2-Foot and 4-Foot Linear Array Microphone

Shure MXA710 linear array microphone user guide. Learn how to install the mic in a variety of rooms and how to use Shure's trusted IntelliM

ix DSP platform.

Version: 4 (2020-G)

Shure Incorporated
2/37
Table of Contents
MXA7102-Foot and 4-Foot Linear Array Microphone 4
Getting Started 4
Step 1: Connect to a Network and Discover Devices 4
Step 2: Route Audio and Apply DSP 4
Step 3: Adjust Microphone Coverage 5
General Description 6
Features 6
MXA710 Parts 6
Model Variations 8
Power Over Ethernet (PoE) 8
Cable Requirements 9
What's in the Box 9
Reset Button 9
Reset Modes 10
Installation Guide 10
Choosing Where to Install the MXA710 10
Suspending the Microphone from the Ceiling 11
Installing the Wall-Mounting Bracket 12
VESA MIS-B Compatibility 14
Covering the Microphone with Fabric 14
Controlling Devices with Shure Designer Software 15
How to Adjust Microphone Coverage 15
MXA710 Coverage Examples 16
Using Autofocus to Improve Coverage 20
Adjusting Levels 21
Using Designer's Optimize Workflow 21
IntelliMix DSP 22
DSP Best Practices 22
Acoustic Echo Cancellation 22
Noise Reduction 23
Automatic Gain Control (AGC) 23
Delay 24
Compressor 24
Automix 24
Automix Settings 24
Automix Modes 25
Automix Channel 25
Mute Synchronization 26
Firmware Updates 26
Firmware Versioning 26
Networking Best Practices 26
Switch and Cable Recommendations for Dante Network
ing 27
Setting Latency 27
Network Audio and Shure Control Data 27
QoS (Quality of Service) Settings 28
Digital Audio Networking 28
Compatibility with Dante Domain Manager 28
Dante Flows for Shure Devices 29
AES67 29
Sending Audio from a Shure Device 30
Receiving Audio from a Device Using a Different Audio 
Network Protocol 30
IP Ports and Protocols 30
Using a Third-Party Control System 31
Optional Accessories 31

Shure Incorporated

3/37

Specifications 32

MXA710 Frequency Response 34

Lobe Sensitivity 34

IMPORTANT SAFETY INSTRUCTIONS 35

Important Product Information 36

Information to the user 36

Contact Customer Support 37

Shure Incorporated

4/37

•

MXA710

2-Foot and 4-Foot Linear Array Microphone

Getting Started

To control MXA710 microphones, use Shure Designer software. After completing this basic setup process, you should be able

to:

Discover the MXA710 in Designer

Design microphone coverage

Apply DSP and route signals

You will need:

Cat5e (or better) Ethernet cable

Network switch that provides Power over Ethernet (PoE)

Shure Designer software installed on a computer. Download at www.shure.com/designer.

Step 1: Connect to a Network and Discover Devices

After installing your microphone, connect it to a PoE port on the network switch using Cat5e (or better) cable.

Connect your computer running Designer to the same network.

Open Designer. Check that you’re connected to the correct network in Settings.

Click Online devices. A list of online devices appears.

To identify devices, click the product icon to flash the lights on a device. Find the MXA710 in the list.

Step 2: Route Audio and Apply DSP

The easiest way to route audio and apply DSP is with Designer's Optimize workflow. Optimize automatically routes audio sig

nals, applies DSP settings, turns on mute synchronization, and enables LED logic control for connected devices.

The MXA710 includes IntelliMix DSP that can be applied to the automix channel output.

For this example, we'll connect an MXA710 and an ANIUSB-MATRIX.

From My projects, select New to create a new project. Click New to add a location to your project.

Select Live mode. Any online devices appear in the list. Drag and drop the MXA710 and the ANIUSB-MATRIX to add

them to your location.

Designer prompts you to choose an installation method for the MXA710. You can change this setting later in Coverage

map.

Shure Incorporated

5/37

◦

Select Optimize.

Check the audio routes and settings to make sure they fit your needs. You might need to:

Delete unnecessary routes.

Verify that AEC reference signals are correctly routed.

Fine-tune DSP blocks as needed.

You can also route audio manually in Designer outside of the Optimize workflow, or use Dante Controller.

Step 3: Adjust Microphone Coverage

Go to Coverage map to adjust the MXA710's coverage. Choose a device installation template:

Wall horizontal

Wall vertical

Ceiling

Table

These templates are designed and tested to fit most common installations, but you can adjust lobe position and width

as needed.

Listen to each of your microphone's channels and adjust the lobe position, width, and gain as needed. The solid line in

each lobe shows where pickup is the strongest. The lobe's edge is -6 dB down from the solid line.

Shure Incorporated

6/37

•

After you have coverage set up, you can send audio from the ANIUSB-MATRIX to other Dante devices or analog sources.

General Description

The Shure Microflex Advance MXA710 Linear Array Microphone represents the next evolution in Shure array microphone

technology, designed for high-quality audio capture in premium AV conferencing environments. The linear form factor of the

MXA710 allows for placement virtually anywhere in a meeting space, including on a wall, around a display, on a ceiling, or in a

conference room table. Available in 2 and 4foot lengths in 3 colors, the MXA710 includes proprietary IntelliMix DSP and Auto

focus technology that provides all the processing needed for echo- and noise-free audio.

Features

Steerable Coverage technology to capture audio anywhere in the room (up to 4 lobes with a 2-foot array, 8 lobes with a

4-foot array)

Autofocus technology fine-tunes each lobe position in real time, even if meeting participants lean back or stand up.

Default room coverage template enables quick and easy lobe optimization for wall, ceiling, or table installations.

IntelliMix DSP includes automatic mixing, acoustic echo cancellation, noise reduction, and automatic gain control.

Shure Designer System Configuration software for easy setup and configuration

SystemOn Audio Asset Management software for remote management and troubleshooting

PoE powered

LED status bars with configurable colors and brightness

Dante & AES67 audio networking protocols

Shure network audio encryption compatible

Multiple mounting accessories available for wall, ceiling, or table installation

®™

™

Shure Incorporated

7/37

MXA710 Parts

Mute status LED

Customize LED color and behavior in Designer by going to: Device configuration > Settings > Lights.

Default Settings

Microphone Status LED Color/Behavior

Active Green (solid)

Muted Red (solid)

Hardware identification Green (flashing)

Firmware update in progress Green (progresses along bar)

Reset Network reset: Red (progresses along bar)

Factory reset: Triggers device power-up

Error Red (split, alternate flashing)

Device power-up Multi-color flash, then blue (moves quickly back and forth

across bar)

Shure Incorporated

8/37

◦

•

Note: If LEDs are disabled, they will still turn on when the device powers up or when an error state occurs.

Reset button

Sits behind the microphone grille. To access, find a grille hole that aligns with the left edge of the mute status LED and

the "S" of the Shure logo. Use a small paperclip or other tool to press and hold the button. You may need to try a few

different holes to press the reset button.

Network port

RJ-45 jack for network connection. Power over Ethernet is required to power the microphone.

Network status LED (green)

Off = No network link

On = Network link established

Flashing = Network link active

Network speed LED (amber)

Off = 10/100 Mbps

On = 1 Gbps

Mounting keyholes

Use to attach the microphone to the wall-mounting bracket.

Screw holes for suspension mounting

Use to attach eyelet screws to hold braided metal cable or other high-strength wire for suspension mounting.

Cable exit

Route the Ethernet cable here to keep it flush with the microphone.

Screw holes (VESA MIS-B compatibility)

Use to attach the desk stand, the microphone stand mount, or other VESA MIS-B-compatible adapters.

Model Variations

SKU Description

MXA710B-2FT Black 2-foot microphone (60 cm)

MXA710W-2FT White 2-foot microphone (60 cm)

MXA710AL-2FT Aluminum 2-foot microphone (60 cm)

MXA710B-4FT Black 4-foot microphone (120 cm)

MXA710W-4FT White 4-foot microphone (120 cm)

MXA710AL-4FT Aluminum 4-foot microphone (120 cm)

Power Over Ethernet (PoE)

This device requires PoE to operate. It is compatible with Class 0 PoE sources.

Power over Ethernet is delivered in one of the following ways:

A network switch that provides PoE

A PoE injector device

Shure Incorporated

9/37

Cable Requirements

Always use Cat5E cable or higher.

What's in the Box

2-foot or 4-foot linear array microphone MXA710-2FT or MXA710-4FT

Wall-mounting bracket (2 or 4-foot) RPM710-2M or RPM710-4M

Hardware kit with:

Wall cover plate and screws (US and UK versions)

Mounting eyelet screws (2)

Washers for eyelet screws (2)

Cable ties (2)

RPM710-H

Reset Button

The reset button is behind the grille and can be pushed with a small paperclip or other tool. To access the button:

Find the end of the microphone that has the Shure logo printed on the side.

Find the left edge of the microphone light, which sits behind the grille.

Insert the paperclip into the grille hole that aligns with the left edge of the microphone light and the "S" of the Shure lo

go. Press and hold to reset the microphone. If you don't feel a button, try the grille holes below and around the first one.

You may need to try a few different holes to press the reset button.

Shure Incorporated

10/37

•

◦

•

Reset Modes

Network reset (press for 4-8 seconds): Resets all Shure control and audio network IP settings to factory defaults.

Full factory reset (press for more than 8 seconds): Resets all network and configuration settings to the factory defaults.

Installation Guide

Choosing Where to Install the MXA710

The MXA710 is an extremely versatile microphone. You can install it in many places in a conference room and easily get good

coverage for all talkers.

MXA710-2FT MXA710-4FT

Room size Small to medium Medium to large

Maximum number of lobes 4 8

Recommended distance from talkers 2 to 16 feet 4 to 20 feet

Best Practices for Installation

Before installing, open the microphone's coverage map in Designer. Look at the 4 device installation templates to under

stand how the lobes behave when you move them around and use different widths. Lobes also have Autofocus technolo

gy, which fine-tunes each lobe position in real time, even if meeting participants lean back or stand up. Templates are

available for:

Wall horizontal

Wall vertical

Ceiling

Table

Measure your space and make sure that all talkers will fit in the microphone's coverage area.

Coverage also depends on your room's acoustics, construction, and materials. Take these into consideration when plan

ning coverage.

Don't place the microphone behind obstructions. Keep the microphone's grille at least 36 inches away from any occupan

cy sensors.

Plan for any future coverage needs.

Ways to Install the MXA710

Accessory Install location Other hardware required?

Wall-mounting bracket Wall Drywall mounting screws and anchors

Display mount kit Attach to display mount

Peerless Universal Sound Bar Kit,

Chief Thinstall Center Channel Speaker

Adapter, or other similar adapter with

VESA MIS-B compatibility

Suspended Cable Ceiling

Braided metal cable

Hardware to attach cable to ceiling or

A710-TB Tile Bridge

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Shure Mikrofon Handbücher

Shure

Shure VP64A Bedienungsanleitung

Shure

Shure 548 Bedienungsanleitung

Shure

Shure 526T Series II Super Punch Bedienungsanleitung

Shure

Shure KSM137 Bedienungsanleitung

Shure

Shure M44G Bedienungsanleitung

Shure

Shure 708S Stratoliner Bedienungsanleitung

Shure

Shure Microflex M300 Series Bedienungsanleitung

Shure

Shure AMS22 Bedienungsanleitung

Shure

Shure MX150/C Bedienungsanleitung

Shure

Shure 588SDX Bedienungsanleitung

Shure

Shure KSM27 Bedienungsanleitung

Shure

Shure PG ALTA PGA 57 Bedienungsanleitung

Shure

Shure UNIDYNE III Series Bedienungsanleitung

Shure

Shure PGA 48 Bedienungsanleitung

Shure

Shure Microflex MX396 Bedienungsanleitung

Shure

Shure KSM32 Bedienungsanleitung

Shure

Shure PGA181 PG Alta series Bedienungsanleitung

Shure

Shure 440 Bedienungsanleitung

Shure

Shure BETA 87C Bedienungsanleitung

Shure

Shure Microflex MX400SE Series Bedienungsanleitung

Shure

Shure BETA 98AMP Bedienungsanleitung

Shure

Shure 589C Bedienungsanleitung

Shure

Shure Microflex MX400S Bedienungsanleitung

Shure

Shure 104C Bedienungsanleitung

Beliebte Mikrofon Handbücher anderer Marken

IK Multimedia

IK Multimedia iRig Stream MIC PRO Bedienungsanleitung

DAPAudio

DAPAudio RM-101 Bedienungsanleitung

AKG

AKG CHM 21 Bedienungsanleitung

Sennheiser

Sennheiser evolution wireless series EM 100 Bedienungsanleitung

Sony

Sony C-48 Bedienungsanleitung

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Bedienungsanleitung

auna PRO

auna PRO MIC-900 Bedienungsanleitung

AKG

AKG D 3800 Bedienungsanleitung

MAIIN SOUND

MAIIN SOUND IIN style Bedienungsanleitung

Earthworks

Earthworks TC25 Bedienungsanleitung

Sennheiser

Sennheiser evolution D1 Bedienungsanleitung

Alesis

Alesis MicLink Wireless Bedienungsanleitung

DSPPA

DSPPA D6234 Bedienungsanleitung

Monacor

Monacor IMG STAGELINE ECM-300B Bedienungsanleitung

Ansr Audio

Ansr Audio Scan16 Bedienungsanleitung

JLab

JLab GO TALK Bedienungsanleitung

Renkforce

Renkforce TY-109 Bedienungsanleitung

Trust

Trust 31008 Bedienungsanleitung