Delta DRP048V240W1B Series Bedienungsanleitung

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Highlights & Features

– Worldwide AC input range without power de-rating

– Power Boost 150% for 5 seconds

– Full corrosion resistant Aluminium chassis

– Extreme low temperature cold start at -40°C

– Conformal coating on PCBA to protect against chemical and

dust pollutants

– Hazardous Locations approval to ATEX and Class I, Div 2

(DRP048V240W1BA)

– Overvoltage / Overcurrent / Over Temperature Protections

– IP20 Compliant

Safety Standards

CB Certified for worldwide use

Model Number: DRP048V240W1B□

Unit Weight:0.96 kg

Dimensions (L x W x D): 121 x 85 x 124.1 mm

General Description

The CliQ II 1-phase DIN Rail power supply series also offers output voltage of 48V. These products are encased in rugged yet

lightweight full aluminium body that can withstand shock and vibration according to IEC 60068-2 standard. The series of 1-phase

products operates over a wide temperature range of -25°C to +80°C and wide input range from 85Vac to 264Vac, with no power

de-rating throughout the entire range. Another great feature is the conformal coating on the PCBA which allows selected models to be

certified to ATEX and Class I, Div 2 for use in hazardous locations. The design conforms to harmonic current emission

IEC/EN 61000-3-2 standard.

Model Information

CliQ II DIN Rail Power Supply

Model

Number

Input Voltage Range

Output

oltage

Output

Curr

ent

DRP048V240W1B□ 85-264Vac (120-375Vdc) 48Vdc 5.00A

Model Numbering

DR P048V240W 1B

□

DIN Rail Power Supply Output Voltage Output Power Single Phase CliQ II Series A - Metal Case,

with Class I, Div 2

N - Metal Case,

without Class I, Div 2

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Specifications

Input Ratings / Characteristics

Nominal Input Voltage 100-240Vac

Input Voltage Range 85-264Vac

Nominal Input Frequency 50-60Hz

Input Frequency Range 47-63Hz

Nominal DC Input Voltage 125-250Vdc

DC Input Voltage Range* 120-375Vdc

Input Current < 2.50A @ 115Vac, < 1.30A @ 230Vac

Efficiency at 100% Load > 90.0% @ 115Vac, > 92.0% @ 230Vac

Max Inrush Current < 35A @ 115Vac & 230Vac

Power Factor > 0.96 @ 115Vac, > 0.90 @ 230Vac

Leakage Current < 1mA @ 240Vac

*Fulfills tested conditions

Output Ratings / Characteristics

Nominal Output Voltage 48Vdc

Output Voltage Tolerance ± 1% (initial set point tolerance from factory)

Output Voltage Adjustment Range 48-56Vdc

Output Current 5.00A (continuously operating at 48V)

7.50A (Power Boost for 5 seconds at 48V, refer to the

details in the Functions section)

Output Power 240W (continuously operating)

360

W (Power Boost for 5 seconds, refer to the details in

the Functions section)

Line Regulation < 0.5% typ. (@ 320-600Vac input, 100% load)

Load Regulation < 1% typ. (@ 320-600Vac input, 0-100% load)

PARD (20MHz) < 200mVpp

Rise Time

< 200ms @ nominal input (100% load)

Start-up Time < 1,000ms @ nominal input (100% load)

Hold-up Time > 20ms @ 115Vac & 230Vac (100% load)

Dynamic Response (Overshoot & Undershoot O/P Voltage) ± 2% @ 10-100% load

Start-up with Capacitive Loads 10,000µF Max

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Mechanical

Case Cover / Chassis Aluminium

Dimensions (L x W x D) 121 x 85 x 124.1 mm

Unit Weight 0.96 kg

Indicator Green LED (DC OK)

Cooling System Convection

Terminal Input 3 Pins (Rated 300V/15A)

Output 4 Pins (Rated 300V/15A)

Wire AWG 20-12

Mounting Rail Standard TS35 DIN Rail in accordance with EN 60715

Noise (1 Meter from power supply) Sound Pressure Level (SPL) < 40dBA

Environment

Surrounding Air Temperature

Operating

-25°C to +80°C

Storage -25°C to +85°C

Power De-rating Vertical Mounting > 50°C de-rate power by 2.5% / °C

Horizontal Mounting > 40°C de-rate power by 2.5% / °C

Operating Humidity < 95% RH (Non-Condensing)

Operating Altitude 2,500 Meters

Shock Test (Non-Operating) IEC 60068-2-27, 30G (300m/S²) for a duration of 18ms,

1 times per direction, 2 times in total

Vibration (Non-Operating) IEC 60068-2-6, 10Hz to 500Hz @ 30m/S² (3G peak);

60 min per axis for all X, Y, Z direction

Pollution Degree 2

Protections

Overvoltage < 57V, SELV Output, Hicc-up Mode,

Non-Latching (Auto-Recovery)

Overload / Overcurrent > 150% of rated load current, Hicc-up Mode,

Non-Latching (Auto-Recovery)

Over Temperature < 80°C Surrounding Air Temperature @ 100% load,

Non-Latching (Auto-Recovery)

Short Circuit Hicc-up Mode, Non-Latching

(Auto-Recovery when the fault is removed)

Degree of Protection IP20

Protection Against Shock Class I with PE* connection

*PE: Primary Earth

Reliability Data

MTBF > 500,000 hrs. as per Telcordia SR-332

I/P: 115Vac, O/P: 100% load, Ta: 25°C

Expected Cap Life Time 10 years (400Vac & 500Vac, 50% load @ 40°C)

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Safety Standards / Directives

Electrical Equipment in Power Installations

EN 50178 / IEC 62103

Electrical Safety SIQ to EN 60950-1, UL/cUL recognized to UL 60950-1

and CSA C22.2 No. 60950-1, CB scheme to

IEC 60950-1

Industrial Control Equipment UL/cUL listed to UL 508 and CSA C22.2 No. 107.1-01,

CSA to CSA C22.2 No. 107.1-01 (File No. 181564)

Hazardous Location / ATEX (For DRP048V240W1BA) cCSAus to CSA C22.2 No. 213-M1987, ANSI / ISA

12.12.01:2007 [Class I, Division 2, Group A, B, C, D T4,

Ta= -25°C to +80°C (Vertical: > +50°C derating,

Horizontal: > +40°C derating)]

EN 60079-0:2009, EN 60079-15:2010 [ II 3G Ex nA

nC IIC T4 Gc, Ta= -25°C to +80°C (Vertical: > +50°C

derating, Horizontal: > +40°C derating)]

II 3G ATEX 94/9/EC (For DRP048V240W1BA) Certificate No. EPS 12 ATEX 1 491 X

CE In conformance with EMC Directive 2004/108/EC and

Low Voltage Directive 2006/95/EC

For DRP048V240W1BA:

In conformance with Equipment for explosive

atmospheres (ATEX) directive 94/9/EC

Material and Parts RoHS Directive 2011/65/EU Compliant

Galvanic Isolation Input to Output 4.0KVac

Input to Ground 1.5KVac

Output to Ground 1.5KVac

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

EMC

EMC / Emissions CISPR 22, EN 55022, CISPR 11, EN 55011,

FCC Title 47: Class B

Component Power Supply for General Use EN 61204-3

Immunity to EN 55024, EN 61000-6-1, EN 61000-6-2

Electrostatic Discharge IEC 61000-4-2 Level 4 Criteria A

Air Discharge: 15kV

Contact Discharge: 8kV

Radiated Field IEC 61000-4-3 Level 3 Criteria A1)

80MHz-1GHz, 10V/M, 80% modulation (1kHz)

Electrical Fast Transient / Burst IEC 61000-4-4 Level 3 Criteria A

2kV

Surge IEC 61000-4-5 Level 3 Criteria A

Common Mode2): 2kV

Differential Mode

: 1kV

Conducted IEC 61000-4-6 Level 3 Criteria A1)

150kHz-80MHz, 10Vrms

Power Frequency Magnetic Fields IEC 61000-4-8 Criteria A

10A/Meter

Voltage Dips IEC 61000-4-11 100% dip; 1 cycle (20ms); Self Recoverable

Low Energy Pulse Test (Ring Wave) IEC 61000-4-12 Level 3 Criteria A

Common Mode2): 2kV

Differential Mode

: 1kV

Harmonic Current Emission IEC/EN 61000-3-2, Class A

Voltage Fluctuation and Flicker IEC/EN 61000-3-3

1) Criteria A: Normal performance within the specification limits

2) Asymmetrical: Common mode (Line to earth)

3) Symmetrical: Differential mode (Line to line)

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Block Diagram

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Device Description

1) Input terminal block connector

2) Output terminal block connector

3) DC Voltage adjustment potentiometer

4) DC OK control LED (Green)

5) Universal mounting rail system

Dimensions

L x W x D: 121 x 85 x 124.1 mm

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Engineering Data

De-rating

Output De-rating VS. Input Voltage

Note

1. Power supply components may degrade, or

be damaged, when the power supply is

continuously used outside the shaded region,

refer to the graph shown in Fig. 1.

2. If the output capacity is not reduced when the

surrounding air temperature > 50°C (Vertical)

or > 40°C (Horizontal), the device may run

into Over Temperature Protection. When

activated, the output voltage will go into

bouncing mode and will recover when the

surrounding air temperature is lowered or the

load is reduced as far as necessary to keep

the device in working condition.

3. In order for the device to function in the

manner intended, it is also necessary to keep

a safety distance of 20mm with adjacent units

while the device is in operation.

Depending on the surrounding air

temperature and output load delivered by the

power supply, the device can be very hot!

5. If the device has to be mounted in any other

orientation, please do not hesitate to contact

info@deltapsu.com for more details.

Fig. 1 De-rating for Vertical Mounting Orientation

> 50°C de-rate power by 2.5% / °C

De-rating for Horizontal Mounting Orientation

> 40°C de-rate power by 2.5% / °C

No output power de-rating across the entire

input voltage range

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Assembly & Installation

The power supply unit (PSU) can be mounted on 35mm DIN rails in accordance with EN 60715. The device should be installed with

input terminal block at the bottom.

Each device is delivered ready to install.

Mounting

Dismounting

Fig. 2.1 Mounting

Snap on the DIN rail as shown in Fig. 2.1:

1. Tilt the unit upwards and insert it onto the DIN rail.

2. Push downwards until stopped.

3. Press against the bottom front side for locking.

4. Shake the unit slightly to ensure that it is secured.

Fig. 2.2 Dismounting

To uninstall, pull or slide down the latch with screw driver as

shown in Fig. 2.2. Then slide the power supply unit (PSU) in

the opposite direction, release the latch and pull out the power

supply unit (PSU) from the rail.

CAUTION: Must tighten wire to housing (Fig. 3.1) before

plugging into the terminal block connection (Fig. 3.2).

In accordance to EN 60950 / UL 50950, flexible cables require

ferrules. Use appropriate copper cables designed to sustain

operating temperature of:

1. 60°C / 75°C for USA

2. At least 75°C for ambient not exceeding 60°C, and

90°C for ambient exceeding 60°C for Canada.

Connection

Fig. 3.1 Fig. 3.2

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

48V 240W 1

Phase

/ DRP048V240W1B

□

All parameters are specified at 25°C ambient unless otherwise noted.

www.DeltaPSU.com (September 2013, Rev. 01)

Safety Instructions

Vertical Mounting

– ALWAYS switch mains of input power OFF before connecting and disconnecting the input voltage to the unit. If mains are not

turned OFF, there is risk of explosion / severe damage.

– To guarantee sufficient convection cooling, keep a distance of 50mm above and below the device as well as a lateral

distance of 20mm to other units.

– Note that the enclosure of the device can become very hot depending on the surrounding air temperature and load of the power

supply. Risk of burns!

– Only plug in and unplug connectors when power is turned off!

– DO NOT insert any objects into the unit.

– Hazardous voltages may be present for up to 5 minutes after the input mains voltage is disconnected. Do not touch the unit during

this time.

– The power supplies are built in units and must be installed in a cabinet or room (condensation free environment and indoor

location) that is relatively free of conductive contaminants.

– CAUTION: “For use in a controlled environment”.

For DRP048V240W1BA:

– The power supplies unit must be installed in an IP54 enclosure or cabinet in the final installation. The enclosure or cabinet must

comply with EN 60079-0 or EN 60079-15.

– Warning: Explosion Hazard – Substitution of components may impair suitability for Class I, Division 2.

– Warning: Explosion Hazard – Do not disconnect equipment or adjust potentiometer unless the power has been switched off or the

area is known to be non-hazardous.

Horizontal Mounting

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Delta Stromversorgung Handbücher

Delta

Delta CliQ Bedienungsanleitung

Delta

Delta PMC-05V050W1AA Bedienungsanleitung

Delta

Delta PMC-24V050W1AA Bedienungsanleitung

Delta

Delta PMC-05V035W1AA Bedienungsanleitung

Delta

Delta LZ-16/R10 Bedienungsanleitung

Delta

Delta PMC Series Bedienungsanleitung

Delta

Delta PCM-48V600W1B Series Bedienungsanleitung

Delta

Delta GPS-1000D8 A A22 Bedienungsanleitung

Delta

Delta DVPPS01 Bedienungsanleitung

Delta

Delta GPS-850HB A A22 Bedienungsanleitung

Delta

Delta PMT2 75 W Series Bedienungsanleitung

Delta

Delta PJB-24V240W Series Bedienungsanleitung

Delta

Delta HPP-1K5A01KAT Bedienungsanleitung

Delta

Delta 24V/8A/PA18AC Bedienungsanleitung

Delta

Delta PMC-24V300W1BA Bedienungsanleitung

Delta

Delta PMU-27V155WC A Series Bedienungsanleitung

Delta

Delta PMC-12V035W1AA Bedienungsanleitung

Delta

Delta LZ-8P/R19 Bedienungsanleitung

Delta

Delta PMC-24V100W1AB Bedienungsanleitung

Delta

Delta PMC-24V100W1AA Bedienungsanleitung

Delta

Delta PJB-24V300W Series Bedienungsanleitung

Delta

Delta PMC-24V075W1AA Bedienungsanleitung

Delta

Delta LOYTEC LPOW-2415A Bedienungsanleitung

Delta

Delta PMC-24V150W1AA Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung