Demco 90016 Ergo E.Eazy Bedienungsanleitung

123456789012345678901234567890121234567890123456789012

90016

ERGO-E.EAZY Sit/Stand

Assembly Instructions

2

P8 CPU Side Brace 1 EA

P9 Cable Tray 1 EA

P10 Keyboard Shelf 1 EA

P1 Top Panel 1 EA

P2 Upper Leg 2 EA

P3 Center Post 1 EA

P4 Lower Leg 1 EA

P5 Foot 2 EA

P6 CPU Brace 2 EA

P7 CPU Shelf 1 EA

Part Drawing Description Qty Part Drawing Description Qty

WOW

Hardware List

A Screw M6*15mm 22 EA

A1 Screw M8*25mm 4 EA

BLock Washer 4 EA

CWood Screw 22 EA

DLocking Caster 2 EA

ENon-Locking Caster 2 EA

F Allen Wrench (M6) 1 EA

G Allen Wrench (M8) 1 EA

H Caster Wrench 1 EA

I T-Handle 2 EA

J Plate Caster 1 EA

K1 Keyboard Plate 1 EA

K2 Keyboard Adjuster 1 EA

K3 Keyboard Stop 1 EA

K4 Keyboard Cap 1 EA

90016 Ergo-E.Eazy Sit/Stand

3

Identify and Separate all the Parts

and Hardware.

1.)

2.)

R

EAD

T

HROUGH

I

NSTRUCTIONS

FROM

BEGINNING

TO

END

BEFORE

STARTING

TO

ASSEMBLE

UNIT

.

Place the Top Panel (P1) upside

down on a padded surface.

Take an Upper Leg (P2) and line

it up with the embedded

threaded inserts on the left side

of the Top. Attache the Upper

Leg using two Screws (A).

Tighten with Allen Wrench (F).

Repeat this Step to attach the

second Upper Leg (P2) on the

right side of the Top as shown in

illustration #1.

Illustration # 1

A

P2

P1

P2

A

3b .)

Attach the Center Post (P3) to the bottom of

the Top Panel (P1) using four Screws (A) as

shown in illustration #2a.

Cut the large safety strap on the Center Post.

Illustration # 2a

Illustration # 2b

3a.) After the Center Post is attached to the

Top, carefully cut the Safety Strap that

is around the Adjustment Lever. Stand

to the side and open the Lever to allow

the post to extend.

P1

A

P3

4

Illustration # 3

Illustration # 4

4.)

P2

P3

5.)

P4

P2

Slide the Lower Leg (P4) down

onto the two Upper Legs (P2)

and the Center Post (P3) as

shown in illustration #3.

Attach a Foot (P5) to the bottom of the left

vertical post of the Lower Leg (P4) using two

Screws (A1). Tighten Screws using Allen

Wrench (G). Repeat this Step to instal the

second Foot to the right vertical post as

shown in illustration #4.

A1

P5

5

6.)

Illustration # 5

A

P7

P6

Attach two CPU Braces (P6) to the bottom of either

the Right Foot or the Left Foot using two Screws (A)

to secure each. Attach the CPU Shelf (P7) to the

CPU Braces using four Screws (A) as shown in

illustration #5. Tighten Screws with Allen Wrech (F).

7.)

CPU can be

attached to

this foot

Illustration #6

Attach the CPU Side Brace (P8) to

the outside edge of the CPU Shelf

(P7) using two Screws (A) as shown

in illustration #6. P8

A

6

Illustration #8

Illustration #7

8.)

9.)

Place a Lock Washer (B) on each

Caster’s thread stem before installing.

Install two Locking Casters (D) on the user

side of the unit. Install two Non-Locking

Casters (E) on the back side of the unit as

shown in illustration #7. Tighten Casters

using Caster Wrench (H).

B

E

B

E

D

P1

P9

C

Attach the Cable Tray (P9) to the back edge of

the Top Panel (P1) using four Wood Screws (C)

into the predrilled holes. The Cable Tray can

be turned so that the opening will face to the

back or turned so it faces the user.

See illustration #8.

7

Illustration #10

Illustration #9

11.)

10.)

I

Screw in a T-Handle (I) height adjuster

into each leg as shown in illustration #9.

C

K1

Attach the Keyboard Plate (K1) to either the right

or left side of the Top. Line up the plate with the

predrilled holes in the Top. Use eight Wood

Screws (C) to secure the plate to the bottom of

the Top Panel.

8

12.)

C

K3

Illustration #11

Attach the rubber Keyboard

Stop (K3) to the back of the Keyboard

Plate (K1) using one Wood Screw (C).

13.)

Illustration #12

Slide the Keyboard Adjuster (K2) into the Keyboard Plate (K1) as shown in illustration #12.

Attach the Keyboard Cap (K4) to the end of the Keyboard Plate as shown in Detail #1.

Secure the Keyboard Cap in place using three Wood Screws (C).

K2

K4

K1

Detail

#1

9

Illustration #13

14.) Attach the Keyboard Shelf (P10) to

the Keyboard Adjuster (K2) using

six Wood Screws (C) as shown in

illustration #13.

P10

C

15.) Attach Plate Caster (J) to the bottom of the CPU Shelf (P7) using four Screws (A)

as shown in illustration #14.

Illustration #14

J

P7

A

10

90016

ERGO-E.EAZY Sit/Stand

47 1/2”

23 5/8”

22”

36 1/4”

7 7/8” X 15 3/4”

CPU Shelf

11 3/4” X 26 3/4”

Keyboard Shelf

30 1/2”-

46”

90016_02-25-16

Find Balt® Ergo E. Eazy Sit/Stand Workstation @demco.com

Search:

1372187

Call 800.962.4463 or email [email protected]

Demco 90016 Ergo E.Eazy Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken