Denali DialDim DNL.WHS.23900 Bedienungsanleitung

Instruction Rev00

0mm 10 20 30 40 50 60 70 80 90

Thank you for choosing DENALI

We know you would rather be riding your bike than wrenching on it, so we go the extra

mile to make sure our instructions are clear and as easy to understand as possible. If

you have any questions, comments, or suggestions don’t hesitate to give our experts

a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM

Please Read Before Installing

DENALI products should always be installed by a qualified motorcycle technician. If

you are unsure of your ability to properly install a product, please have the product

installed by your local motorcycle dealer. DENALI takes no responsibility for damages

caused by improper installation. Caution: When installing electronics it is extremely

important to pay close attention to how wires are routed, especially when mounting

products to the front fender, front fork, or fairing of your motorcycle. Always be sure

to turn the handlebars fully left, fully right, and fully compress the suspension to

ensure the wires will not bind and have enough slack for your motorcycle to operate

properly.

Installation Tips

We strongly recommend using medium strength liquid thread locker on all screws and

bolts. It is also important to ensure that all hardware is tightened to the proper torque

specifications as listed in your owner’s manual. For included accessory hardware

please refer to the default torque specifications provided below. Inspect all hardware

after the first 30 miles to ensure that proper torque specifications are maintained.

Hardware Sizing Guide

Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.

Remember, the length of a screw or bolt is measured from the start of the “mounting

surface” to the end of the screw, so only include the screw head when measuring

countersunk screws.

M3 10.0 in-lbs - 1.0 Nm

M4 23.0 in-lbs -2.5Nm

M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm

M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm

M8 - 13.5 ft-lbs 18.0 Nm

M10 - 30.0 ft-lbs 41.0 Nm

M12 - 52.0 ft-lbs 71.0 Nm

in-lbs

ft-lbs NmBolt Size

0in 123

What’s In The Box?

DENALIELECTRONICS.COM

Instruction Manual

(a) DialDim™ Wiring Harness (Ducati DesertX).............................Qty 1

(a)

DialDim™ Wiring Harness

Ducati DesertX

DNL.WHS.23900

OUTFITTING

GUIDE

Kit Contents

This DialDim Wiring Harness enables plug-&-play connection between our

standard DialDim Lighting Controller and the Ducati DesertX. The harness

replaces the universal posi-tap style input harness that is included with the

universal DialDim Controller, enabling you to simply connect in-line at the

factory headlight, horn, and turn signal connectors.

The DesertX’s battery is located underneath the rider seat.

Step One: To gain access to the battery, remove the Seat.

Step Two: Remove both of the terminals from the battery, starting with

the positive +(Red Terminal).

Step Three: Position the DialDim Controller underneath the rider’s seat,

behind the battery, against the left (clutch) side of the battery box.

Step Four: Remove the fuse from the DialDim fuse holder, then connect

both of the battery leads to the battery, starting with the ground -(Black

Terminal). Then re-install the fuse to the DialDim Fuse holder.

Step Five: Use double-stick tape and/or zip-ties to securely mount the

DialDim Controller to the splash guard. Be sure there is enough clearance

for the seat to be re-installed.

2.2 - Positioning The Controller

1. Harness Overview

1.1 - Overview of Harness

2.1 - Locating the Battery

DENALIELECTRONICS.COM

2. Installing The DialDim Controller

DialDim Controller

(Under Rider Seat)

Headlight

Pass-Through Left Turn

Pass-Through

Right Turn

Pass-Through

Horn

Pass-Through

Output to

DialDim Controller

Battery

(Under Rider Seat)

DENALIELECTRONICS.COM

The DesertX DialDim Harness will be connected in-line to four factory

harness connectors: Headlight, Right Turn Signal, Left Turn Signal, & Horn

Step One: To gain access to the Head Light and Turn Signal connectors,

remove the windscreen. They are all located within a cavity on the front

side of the dash.

Step Two: The headlight connector is located on the back of the factory

headlight housing, it is a black 6-pin connector. Disconnect the factory

headlight connector from the headlight housing, then connect the

“Headlight Pass-Through Connector” of the DialDim Harness in-line.

Step Three: The Left and Right Turn Signal Connectors are located beside

the Head Light Connector. They are both white, 2-Pin connectors that are

labled “L” and “R”. Disconnect the factory Turn Signal Connectors from the

indicators, and connect the respective “Left Turn” and “Right Turn” Pass

Through Connectors of the DialDim Harness in-line.

Step Four: The horn connector is located directly on the factory horn,

which is located at the center of the motorcycle, just above the radiator.

Disconnect the factory horn connector with the RED wire then, connect the

“Horn Pass-Through Connector” of the DialDim Harness in-line.

3.1 - Locating Connectors & Installing the Harness

3. Installing The DialDim Harness

DialDim

Controller

OEM Headlight

Connector

(Molded into Housing)

Battery

Headlight Pass-Through

Connectors

OEM Headlight

Harness

OEM Horn

Connector

Left Turn

Pass-Through

Right Turn

Pass-Through

OEM Turn Signal

Connectors located

behind windscreen

Andere Denali Motorradzubehör Handbücher

Denali

Denali HMT.08.10300 Bedienungsanleitung

Denali

Denali LAH.00.10000.B Bedienungsanleitung

Denali

Denali LAH.00.11600 Bedienungsanleitung

Denali

Denali LAH.23.10200 Bedienungsanleitung

Denali

Denali LAH.01.10700 Bedienungsanleitung

Denali

Denali LAH.11.10700 Bedienungsanleitung

Denali

Denali LAH.07.10401 Bedienungsanleitung

Denali

Denali LAH.23.10000 Bedienungsanleitung

Denali

Denali HMT.22.10100 Bedienungsanleitung

Denali

Denali HMT.04.10200 Bedienungsanleitung

Denali

Denali T3 Bedienungsanleitung

Denali

Denali MA11729 Bedienungsanleitung

Denali

Denali DNL.WHS.084 Bedienungsanleitung

Denali

Denali LAH.23.10100 Bedienungsanleitung

Denali

Denali LAH.07.11000 Bedienungsanleitung

Denali

Denali LAH.08.10900 Bedienungsanleitung

Denali

Denali DialDim Bedienungsanleitung

Denali

Denali HMT.07.11001 Bedienungsanleitung

Denali

Denali MBK.22.10000 Bedienungsanleitung

Denali

Denali LAH.08.10700 Bedienungsanleitung

Denali

Denali LAH.07.11300 Bedienungsanleitung

Denali

Denali SoundBomb DNL.SB.050 Bedienungsanleitung

Denali

Denali B6 Bedienungsanleitung

Denali

Denali T3 Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

SW-Motech

SW-Motech SBL.01.971.10000/B Bedienungsanleitung

GÜDE

GÜDE GSH 180-TC-2 Bedienungsanleitung