Denon ADV-1000 Bedienungsanleitung

Hi-Fi Component

SERVICE MANUAL

MODEL

ADV-1000

DVD SURROUND RECEIVER

Some illustrations using in this service manual are slightly different from the actual set.

16-11, YUSHIMA 3-CHOME, BUNKYOU-KU, TOKYO 113-0034 JAPAN

Telephone: 03 (3837) 5321

For Europe model

X0146 NC 0207

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

SPECIFICATIONS



Audio section

• Power amplifier

Output power: Front: 55 W + 55 W (6 Ω/ohms, 1 kHz with 10% T.H.D.)

Center: 55 W (6 Ω/ohms, 1 kHz with 10% T.H.D.)

Surround: 55 W + 55 W (6 Ω/ohms, 1 kHz with 10% T.H.D.)

Subwoofer: 55 W (6 Ω/ohms, 60 Hz with 10% T.H.D.)

Output terminals:

Front, Center, Subwoofer, Surround:

6 ~16 Ω/ohms

• Analog

Input sensitivity / input impedance: 200 mV / 47 kΩ/kohms

Frequency response: 10 Hz ~ 60 kHz: +1.5, −3 dB (DIRECT mode)

S / N : 94 dB (DIRECT mode)

Rated output: 1.2 V (Subwoofer preout, 20 Hz)

• Digital

Digital input / output: Format Digital audio interface



Video section

• Standard video jacks

Input / output level and inpedance: 1 Vp-p, 75 Ω/ohms

• S-video jacks

Input / output level and inpedance: Y (brightness) signal 1 Vp-p, 75 Ω/ohms

C (color) signal 0.3 Vp-p, 75 Ω/ohms

• AV1 connector

Video output: 1Vp-p, 75Ω/ohms

S-video output: Y (brightness) signal 1 Vp-p, 75 Ω/ohms

C (color) signal 0.3 Vp-p, 75 Ω/ohms

RGB output (DVD only): R/G/B signal 0.7 Vp-p, 75 Ω/ohms

Audio output: L/R (Fixed output)



Tuner section

[FM]

(note: µV at 75 Ω/ohms, 0 dBf=1×10-15 W)

[AM]

Receiving Range: 87.50 MHz~108.00 MHz 522 kHz~1611 kHz

Usable Sensitivity: 1.5 µV (14.8 dBf) 20 µV



DVD section

Signal Format: NTSC/PAL

Applicable discs: (1) DVD-Video discs

1-layer 12 cm single-sided discs, 2-layer 12 cm single-sided discs,

2-layer 12cm double-sided discs (1 layer per side)

1-layer 8 cm single-sided discs, 2-layer 8 cm single-sided discs,

2-layer 8 cm double-sided discs (1 layer per side)

(2) Compact discs (CD-DA, Video CD)

12 cm discs, 8 cm discs

Audio output: Fixed output level: 2 Vrms, (CDR/TYPE, VCR OUT)



Clock, Timer section

Clock system: Power source synchronous system

Timer functions: Everyday timer (DVD or Tuner): 1 setting

Sleep timer: maximum 120 min.



General

Power Supply: AC 230 V, 50 Hz

Power Consumption: 70 W (Stand-by 1 W)

Maximuim external

Dimensions: 434(W) ×80 (H) ×368 (D) mm

Mass: 6.0 kg



Remote Control Unit RC-901

Type: Infrared pulse

Power Supply: DC 3V, 2 R6P batteries

SAFETY PRECAUTIONS

The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK

Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to

chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either

side of the power cord is less than 460 kohms, the unit is defective.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

∗Design and specifications are subject to change without notice in the course of porduct improvement.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

DIAGNOSTICS OF OPTICAL PICKUP AND REPLACING TRAVERSE UNIT

Make failure diagnostics of the Optical Pickup as follows.

If the laser drive current becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced.

The laser drive current is registered on the seal attached to the rear of the Mecha. Unit.

In case of replacing the Pickup, change the whole part of the Traverse Unit.

No mechanical adjustment is necessary after the replacement.

Disc no read,

unsteady playback, etc.

Laser drive current check

HF wave form check

(Refer to page 76, 77)

Present value exceeds

the initial value by 1.5 times

Traverse Unit replacing

(See page 10 for details)

Laser current registering

after replacement

Step: Disc playback

Write the measured value

on the seal attached to the Mecha. Unit

* As to the measuring method, refer to page 4

Label Indication of DVD Mechanism

Laser current consumption value

ex) DVD ***mA, CD ***mA

Example:

DVD 30mA

CD 30mA

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

114

15 28

114

15 28

LD4

(SIGNAL)

LD2

(SIGNAL)

LD1

(GND)

LD3

(GND)

Note for Handling the Laser Pick-up

The protection for the damage of laser diode.

If you want to change the optical device unit from any other units, you must keep the following.

(1) It should be done at the desk already took measures the static electricity in care of removing the OPU's

(Optical device unit) connector cable.

(2) Workers should be put on the "Earth Band".

(3) It shold be done to add the solder to the short land to prevent the broken Laser diode before removing the

24P FFC cable.

(4) Don't touch OPU's connector parts carelessly.

Replacement of the Laser Pick-up (Traverse Unit)

Check the Iop (Laser drive current).

If the present Iop (current) value exceeds +50% of the initial value, replace the Traverse unit (Laser Pick-up) with a new

one.

When measureing Laser drive current (Iop), playback the discs (CD, DVD) described below, measure Iop for CD Laser and

DVD Laser by the test point (LD1 ~ LD4) on the DVD Main P.W.B.

Test Disc : DVD/DVDT-S01 or commercially available discs.

: CD/TCD-784 (manufactured by ALMEDIO INC) or commercially available discs.

Iop Measurement Method

GU-3430 DVD Main Unit foil side

LD2

LD1

1. DVD Laser current measurement

(1) Connect the oscilloscope to LD1 of test point

for GND side and LD2 of test point for signal

side.

(2) Playback the title 1 / chapter 1 of the DVD

Test Disc.

(3) Measure the voltage between LD1 and LD2,

calculate Iop by the formula as shown below.

Iop= Measurement Voltage Value

39 (Resistance Value)

2. CD Laser current measurement

(1) Connect the oscilloscope to LD3 of test point

for GND side and LD4 of test point for signal

side.

(2) Playback the track 1 of the CD Test Disc.

(3) Measure the voltage between LD3 and LD4,

calculate Iop by the formula as shown below.

Iop= Measurement Voltage Value

39 (Resistance Value)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

Optical Pick-up Diagnostics and Replacement

When repairing, carry out failure diagnostics by following the procedure described below.

If the present value of the laser drive current is 50% up to initial value, it is the point of the pickup replacement.

In case of the pickup replacement, replace the Traverse Unit with no adjustment.

The initial value is indicated on the label on back side of Mecha.

NO DISC indicated, Playback not smooth, etc.

Laser drive current check

HF signal check

Traverse Unit replacement (refer to page 10)

Present value: 50% up to initial value

Laser drive current check after replacement.

If the present value is less than 80mA, write on

the new label by hand, put on the new label over

the old label.

If the present value exceeds 80mA,

replace the Traverse Unit with a new one.

Cause: Damaged electrostatically when replaced.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

DISASSEMBLY

( Follow the procedure below in reverse order when reassembling )

2. Front Panel

(1) Remove 4 bottom screws 4from the Front Panel.

(2) Disconnect FFC on the DSP Audio P.W.B. and 2

pcs of 3P connectors (white and blue) on the Power

Supply P.W.B.

(3) With releasing the hooks on both sides, detach the

Front Panel to the arrow direction together with the

Inner Panel.

1. Top Cover

(1) Remove 4 screws 1on both sides.

(2) Remove 6 screws 2on the rear panel.

(3) Remove the top screw 3.

(4) Detach the Top Cover to the arrow direction.

DSP Audio P.W.B.

Power Supply P.W.B.

3P connector (white)

3P connector (blue)

FFC

Inner Panel

Hook

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

3. DVD Mecha. Unit

(1) Remove 4 top screws 5on the DVD Mecha.

(2) Disconnect 2 FFCs and 2 pcs of 8P connectors

from the DVD Mecha.

8P connector

FFC

4. Power Supply P.W.B.

(1) Disconnect FFC, 2P connector, 3P connector, and

7P connector from the Power Supply P.W.B.

(2) Disconnect 6P connector from the Amp P.W.B.

(3) Remove 4 screws 7and the screw 8fixing the

Power Supply P.W.B.

(4) Release 3 P.W.B. supports.

3P connector

7P connector

FFC

6P connector

Amp P.W.B.

2P connector

P.W.B. support

Power Supply P.W.B.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

5. Back Panel

(1) Take off the cord bush.

(2) Remove 5 screws 9and 23 screws  .

6. Video P.W.B.

Disconnect 3 FFCs and 3P connector.

Cord bush

3P connector

FFC

Video P.W.B.



7. DSP Audio P.W.B.

(1) Remove the screw  and 3 screws  .

(2) Disconnect 3 FFCs, 3P connector, and 6P connector.

3P connector

6P connector

FFC

DSP Audio P.W.B.







TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

8. Amp P.W.B.

(1) Remove the screw ! and 4 screws " .

(2) Disconnect FFC and 6P connector.

"

6P connector

FFC

Amp P.W.B.

!

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

ADV-1000

TRAVERSE UNIT DISASSEMBLY

(Follow the procedure below in reverse order when reassembling)

Caution: The optical pickup can be damaged easily by static electricity charged on human body. Take necessary anti-static

measures when repairing around the optical pickup.

1. Guide Clamp Bracket disassembly

(1) Remove 2 screws 1.

(2) Remove Guide Clamp Bracket to arrow direction.

2. Tray disassembly

(1) Remove to arrow direction.

(2) Solder the short-circuit (see in the frame).

Guide Clamp Bracket

Tr ay

Solder to Short-Circuit (DVD)

Solder to Short-Circuit (CD)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Andere Handbücher für ADV-1000

Inhaltsverzeichnis

Andere Denon Stereo-Receiver Handbücher

Denon

Denon AVR-991 Bedienungsanleitung

Denon

Denon AVR-3805 Bedienungsanleitung

Denon

Denon MULTEQXT AVR-4806 Bedienungsanleitung

Denon

Denon AVR 2808CI - AV Receiver Benutzerhandbuch

Denon

Denon AVR-4802R Bedienungsanleitung

Denon

Denon AVR-791 Benutzerhandbuch

Denon

Denon DN-700AVP Bedienungsanleitung

Denon

Denon AVR-X4100W Bedienungsanleitung

Denon

Denon DHT-788BA Bedienungsanleitung

Denon

Denon AVR-X4200W Bedienungsanleitung

Denon

Denon AVR-3801 Bedienungsanleitung

Denon

Denon AVR-X2600H DAB Bedienungsanleitung

Denon

Denon AVR-686S Bedienungsanleitung

Denon

Denon AVR-1906 Bedienungsanleitung

Denon

Denon AVR-587 Bedienungsanleitung

Denon

Denon AV Surround Receiver AVR-5803 Bedienungsanleitung

Denon

Denon AirPlay AVR-4311CI Bedienungsanleitung

Denon

Denon AVR-X4200W Bedienungsanleitung

Denon

Denon DRA-201SA Bedienungsanleitung

Denon

Denon AVR-1708 Bedienungsanleitung

Denon

Denon AVR-E300P Bedienungsanleitung

Denon

Denon MULTEQXT AVR-4306 Bedienungsanleitung

Denon

Denon AVR-3801 Bedienungsanleitung

Denon

Denon AVC-X4800H Bedienungsanleitung

Beliebte Stereo-Receiver Handbücher anderer Marken

Marantz

Marantz CINEMA 70S Bedienungsanleitung

Kenwood

Kenwood KMDX92 Bedienungsanleitung

Yamaha

Yamaha RX-830 Bedienungsanleitung

Pioneer

Pioneer AVH-Z7250BT Bedienungsanleitung

Yamaha

Yamaha RX-750 Bedienungsanleitung

Pioneer

Pioneer SC-LX904 Handbuch

Sony

Sony XAV-1500 Bedienungsanleitung

Radio Shack

Radio Shack DX-399 Bedienungsanleitung

Sony

Sony STR-DE535 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Pioneer

Pioneer SX-1000TA Bedienungsanleitung

Yamaha

Yamaha MusicCast TSR-5B3D Bedienungsanleitung

Sony

Sony STR-DE335 - Fm Stereo/fm-am Receiver Bedienungsanleitung

Sony

Sony STR-DG500 - Multi Channel Av Receiver Bedienungsanleitung

Panasonic

Panasonic AJSD955B - DVCPRO50 STUDIO DECK Bedienungsanleitung

Pioneer

Pioneer SX-838 Bedienungsanleitung

Sherwood

Sherwood S-2660CP Technisches Handbuch

Sony

Sony STR-K790 - Lifier Bedienungsanleitung

Pioneer

Pioneer XR-VS77 Bedienungsanleitung