Denver CRP-717 Bedienungsanleitung

INSTRUCTION MANUAL

BRUKSANVISNING

BETJENINGSVEJLEDNING

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUALE D’ISTRUZIONI

MANUAL DE INSTRUÇÕES

INSTRUCCIONES DE U SO

KÄYTTÖOHJEET

GEBRUIKERSHANDLEIDING

INSTRUKCJA OBSŁUGI

PRIRUČNIK ZA RUKOVANJE

www.denver-electronics.com

www.facebook.com/denverelectronics

CRP-717

DENVER CRP-717.indd 1 15�11�27� ��9:40

ENGLISH

LOCATION OF CONTROLS

FUNCTION AND CONTROLS

1. ANGLE / SHARPNESS CONTROLLER

2. PROJECTION TIME 180° FLIP

3. CLK.ADJ./ MEMORY / M+

4. << TUNE DOWN / HOUR

5. >> TUNE UP / MIN

6. SNOOZE / SLEEP / DIMMER

7. PROJECTI ON ON/OFF

8. VOLUME DOWN / ALARM 1 ON-OFF SET

9. VOLUME UP / ALARM 2 ON-OFF SET

10. POWER ON – OFF / ALARM OFF

11. ALARM 1 BUZZER INDICATION

12. ALARM 1 RADIO INDICATION

13. ALARM 2 BUZZER INDICATION

14. ALARM 2 RADIO INDICATION

15. RATING LABEL (BOTTOM OF UNIT)

16. LED DISPLAY

17. AC POWER CORD

18. BATTERY COMPARTMENT COVER

19. FM ANTENNA

20. SPEAKER

ENG-1

DENVER CRP-717.indd 2 15�11�27� ��9:40

POWER CONNECTION

1. This product operates on AC230V~ 50Hz power supply. Plug the

AC power cord into a household outlet AC source.

2. Clock display will ash 0:00 until set to correct time.

INSTALLING/REPLACING THE BACK-UP BATTERY

This unit is equipped with a battery back-up system, requiring one

DC3V CR2032 lithium battery (not included) to maintain the time

settings and radio presets during AC power outage.

1. Unscrew and remove the BATTERY COMPARTMENT COVER.

2. Install one fresh CR2032 lithium battery into the battery

compartment following the polarity diagram on the BATTERY

COMPARTMENT COVER. Use only the specied size and type

of battery.

3. Replace the BATTERY COMPARTMENT COVER and tighten its

screw.

Note: The unit will operate without a battery installed but your time

& alarm setting and radio presets will be lost and will have to be

reset in the event of power interruption or failure.

IMPORTANT:

Be sure that the battery is installed correctly. Wrong polarity may

damage the unit and void the warranty. For best performance and

longer operating time, we recommend the use of good quality

battery.

BATTERY CARE:

- Use only the size and type of battery specied.

- If the unit is not to be used for an extended period of time,

remove the battery. Old or leaking battery can cause damage to

the unit and may void the warranty.

- Do not try to recharge battery not intended to be recharged; they

can overheat and rupture (Follow battery manufacturer’s

directions).

- Do not dispose of battery in re, battery may leak or explode.

ENG-2

DENVER CRP-717.indd 3 15�11�27� ��9:40

WARNING

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD

This product contains a coin/button cell battery. If the coin/button

cell battery is swallowed, it can cause severe internal burns in just 2

hours and can lead to death.

Keep new and used batteries away from children. If the battery

compartment does not close securely, stop using the product and

keep it away from children.

If you think batteries might have been swallowed or placed inside

any part of the body, seek immediate medical attention.

POWER ON/STANDBY

1. In standby mode, tap the POWER ON-OFF button once to turn

on the unit.

2. Press the POWER ON-OFF button once to return the unit to

standby mode.

TIME MANUAL SETTING

1. Press and hold the CLK.ADJ button, the time will start to ash.

2. Press the << TUNE DOWN / HOUR button to increase the

HOUR.

3. Press the >> TUNE UP / MIN button to increase the MINUTES.

4. Once time is set correctly, press the CLK.ADJ button.

NOTE:

• Press the >> TUNE UP / MIN or << TUNE DOWN / HOUR

button once to increase one number at a time.

• Press and hold the >> TUNE UP / MIN or << TUNE DOWN /

HOUR button to quickly increase the numbers.

ALARM SETTING

You can preset and store two separate alarm settings. It allows you

to set an alarm for yourself and a second as a backup, or use the

second independently timed alarm for a partner.

ENG-3

DENVER CRP-717.indd 4 15�11�27� ��9:40

SETTING ALARM 1

1. Please ensure the radio is OFF.

2. Press and hold the VOLUME DOWN / ALARM 1 ON-OFF SET

button to set ALARM. The alarm time will ash on the display.

3. Press the << TUNE DOWN / HOUR button to increase the

HOUR.

4. Press the >> TUNE UP / MIN button to increase the MINUTES.

5. To toggle between Buzzer and Radio alarm mode, press the

VOLUME DOWN / ALARM 1 ON-OFF SET button until the

desired option is highlighted on the LED display.

• Radio Alarm 1

• Buzzer Alarm 1

6. Once alarm is set, press the CLK.ADJ./ MEMORY / M+ button

once to conrm setting.

SETTING ALARM 2

1. Please ensure the radio is OFF.

2. Press and hold the VOLUME UP / ALARM 2 ON-OFF SET

button to set ALARM 2. The alarm time will ash on the display.

3. Press the << TUNE DOWN / HOUR button to increase the

HOUR.

4. Press the >> TUNE UP / MIN button to increase the MINUTES.

5. To toggle between Buzzer and Radio alarm mode, press the

VOLUME UP / ALARM 2 ON-OFF SET button until the desired

option is highlighted on the LED display.

• Radio Alarm 2

• Buzzer Alarm 2

6. Once alarm is set, press the CLK.ADJ./ MEMORY / M+ button

once to conrm setting.

ENG-4

ALARM 1 BUZZER INDICATION

ALARM 1 RADIO INDICATION

ALARM 2 BUZZER INDICATION

ALARM 2 RADIO INDICATION

DENVER CRP-717.indd 5 15�11�27� ��9:40

SNOOZE FUNCTION

1. When the alarm (buzzer or radio) is triggered, press the

SNOOZE/SLEEP/DIMMER button. The alarm will turn off for

approximately 9 minutes.

2. To cancel the SNOOZE function, press the POWER ON – OFF /

ALARM OFF button.

LISTENING TO THE RADIO

HINTS FOR BEST RECEPTION

FM - To insure maximum FM tuner reception, unwrap and fully

extend the EXTERNAL FM WIRE ANTENNA for best FM radio

reception.

1. Press the POWER ON – OFF / ALARM OFF button once to turn

radio ON.

2. Press the VOLUME DOWN / ALARM 1 ON-OFF SET button to

decrease the volume.

3. Press the VOLUME UP / ALARM 2 ON-OFF SET button to

increase the volume.

4. Press the << TUNE DOWN / HOUR button to decrease the FM

frequency.

5. Press the >> TUNE UP / MIN button to increase the FM

frequency.

6. Press the POWER ON – OFF / ALARM OFF button once to turn

radio OFF.

TO SET / RECALL THE RADIO PRESETS

You can preset and store the frequency of 10 radio stations in the

memory.

1. Press the POWER ON – OFF / ALARM OFF button once to turn

the radio ON.

2. Set radio to desired station.

3. Press and hold the CLK.ADJ./ MEMORY / M+ button and PO1

will ash on the screen.

4. Press the CLK.ADJ./ MEMORY / M+ button to conrm setting to

PO1 or wait 5 seconds for ashing to stop.

5. Repeat the steps above to preset more radio stations.

6. To recall a preset station, press the CLK.ADJ./ MEMORY / M+

button to toggle through the current preset radio stations.

ENG-5

DENVER CRP-717.indd 6 15�11�27� ��9:40

SLEEP TIMER OPERATION

The sleep timer allows you to play music for a preset amount of

time ranging from 90 minutes to 10 minutes. It is commonly used by

people who prefer to go to sleep to music.

1. In radio mode, Press the SNOOZE/SLEEP/DIMMER button.

The display will show 90 minutes, your clock radio will turn off in

90 minutes.

2. To change the number of minutes for the SLEEP timer, press the

SNOOZE/SLEEP/DIMMER button until you see the desired

number of minutes. The SLEEP timer decreases in increments

of 10.

3. To cancel the SLEEP timer, press and the SNOOZE/SLEEP/

DIMMER button then press again until you see OFF in the

display or press the POWER ON – OFF / ALARM OFF button.

DIMMER CONTROL

In radio off mode, Tap the DIMMER button to set the brightness of

the LED display to high, medium or low according to your ambient

light conditions.

Remark:

1. Clock display with dimmer low” is the default setting.

2. It will consume more power if you set the clock display with

dimmer high.

PROJECTION FUNCTION

Notes:

- This appliance is featured with a projection function and can be

used in either clock or radio mode. You can use this appliance to

project time on the ceiling or wall.

- Optimal projection distance ranges from ca. 90 to 270cm.

- Press PROJECTION ON/OFF button to illuminate the projection

lens. Time is projected on the ceiling or wall.

- Use angle/sharpness controller to achieve optimal projection

sharpness and angle.

- Press PROJECTION 180º FLIP button to ip the projected

image.

- To deactivate projection function, simply press PROJECTION

ON/OFF button. The projection lens goes off.

ENG-6

DENVER CRP-717.indd 7 15�11�27� ��9:40

RESETTING THE UNIT

If the system does not respond or exhibits erratic or intermittent

operation, you may have experienced an electrostatic discharge

(ESD) or a power surge that triggered the internal microcontroller to

shut down automatically. If this occurs, disconnect the AC POWER

CORD from the wall and remove the backup battery from the

compartment. Wait at least 3 minutes, and reinsert the battery for

the back-up, and reattach the AC Cord to the wall. The unit is now

reset, so you will need to setup the unit time and alarms again.

SPECIFICATIONS

Frequency : FM 87.5 – 108 MHz

Battery backup : 1 x 3V CR2032 at lithium battery (not included)

Power source : AC 230V ~ 50Hz, 5W

Projection distance: ≤ approx. 90 to 270cm

ENG-7

DENVER CRP-717.indd 8 15�11�27� ��9:40

WARNING

1. No naked ame sources, such as lighted candles, should be

placed on the apparatus.

2. Do not place the product in closed bookcases or racks without

proper ventilation.

3. The mains plug is used as the disconnect device, the disconnect

device shall remain readily operable.

4. The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains,

etc.

5. It shall not be exposed to dripping or splashing and that no

objects lled with liquids, such as vases, shall be placed on the

apparatus.

6. Do not connect FM antenna to outside antenna.

7. The unit should not be exposed to direct sunlight, very high or

low temperature, moisture, vibrations or placed in dusty

environment.

8. Do not use abrasive, benzene, thinner or other solvents to clean

the surface of the unit. To clean, wipe it will mild non-abrasive

detergent solution and clean soft cloth.

9. Never attempt to insert wires, pins or other such objects into the

vents or opening of the unit.

10. Batteries shall not be exposed to excessive heat such as

sunshine, re or the like.

11. Attention should be drawn to the environmental aspects of

battery disposal.

12. Do not dispose this product into usual household garbage at the

end of its lifecycle; hand it over to a collection center for

recycling the electrical and electronic appliances. By recycling,

some of the materials can be reused. You are making an

important contribution to protect our environment. Please inquire

your community administration for the authorized disposal

center.

ENG-8

DENVER CRP-717.indd 9 15�11�27� ��9:40

www.denver-electrionics.com

Electric and electronic equipment contains materials, components

and substances that can be hazardous to your health and the

environment, if the waste material (discarded electric and electronic

equipment) is not handled correctly.

Electric and electronic equipment is marked with the crossed out

trash can symbol, seen below. This symbol signies that electric

and electronic equipment should not be disposed of with other

household waste, but should be disposed of separately.

All cities have established collection points, where electric and

electronic equipment can either be submitted free of charge at

recycling stations and other collection sites, or be collected from

the households. Additional information is available at the technical

department of your city.

Imported by:

DENVER ELECTRONICS A/S

Stavneagervej 22

DK-8250 Egaa

Denmark

www.facebook.com/denverelectronics

ENG-9

DENVER CRP-717.indd 10 15�11�27� ��9:40

Andere Handbücher für CRP-717

Inhaltsverzeichnis

Sprachen:

Andere Denver Radiowecker Handbücher

Denver

Denver CR-213 Bedienungsanleitung

Denver

Denver CR-425 Bedienungsanleitung

Denver

Denver CRL-310 Bedienungsanleitung

Denver

Denver CR-515 Bedienungsanleitung

Denver

Denver CRP-716 Bedienungsanleitung

Denver

Denver CRP-718 Bedienungsanleitung

Denver

Denver CRL-330 Bedienungsanleitung

Denver

Denver DAB-36 Bedienungsanleitung

Denver

Denver CRP-514 Bedienungsanleitung

Denver

Denver DAB-45PLUS Bedienungsanleitung

Denver

Denver CR-419 MK2 Bedienungsanleitung

Denver

Denver CRP-515 Bedienungsanleitung

Denver

Denver CRP-121 Bedienungsanleitung

Denver

Denver CRL-310 Bedienungsanleitung

Denver

Denver CR-812 Bedienungsanleitung

Denver

Denver CR-715 Bedienungsanleitung

Denver

Denver CRCD-213 Bedienungsanleitung

Denver

Denver CRP-112 Bedienungsanleitung

Denver

Denver CRL-290 Bedienungsanleitung

Denver

Denver CRP-714 Bedienungsanleitung

Denver

Denver CRL-330 Bedienungsanleitung

Denver

Denver CRP-210 Bedienungsanleitung

Denver

Denver CRP-618 Bedienungsanleitung

Denver

Denver CRQ-110 Bedienungsanleitung

Beliebte Radiowecker Handbücher anderer Marken

Audiovox

Audiovox CE90 Bedienungsanleitung

Sony

Sony Dream Machine ICF-C763L Bedienungsanleitung

Sanyo

Sanyo DMP-P6 Bedienungsanleitung

Yamaha

Yamaha ISX-80 Bedienungsanleitung

Pyle

Pyle PLMR20W Bedienungsanleitung

Blaupunkt

Blaupunkt CR7BK Bedienungsanleitung

Philips

Philips AJ3180 Bedienungsanleitung

HoMedics

HoMedics SS-5500-2EU Bedienungsanleitung

RCA

RCA RC66i Bedienungsanleitung

Versaudio

Versaudio Vers Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR8100 Bedienungsanleitung

Audiovox

Audiovox CE90 Bedienungsanleitung

Jensen Audio

Jensen Audio JCR-222 - AM/FM Projection Alarm Clock Radio Bedienungsanleitung

Roberts

Roberts ChronoDAB Bedienungsanleitung

AEG

AEG MRC 4132 BT Bedienungsanleitung

Tokai

Tokai TC-155 Bedienungsanleitung

Timex

Timex T300 Bedienungsanleitung

Sony

Sony DREAM MACHINE ICF-C318 Bedienungsanleitung