Detalles iLS 6300BU Bedienungsanleitung
Wireless Laser
Barcode Scanner
iLS 6300BU
User’s Manual
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
Limited Warranty
No warranty of any kind is made in regard to this material, including, but not
limited to, implied warranties of merchantability or fitness for any particular
purpose. We are not liable for any errors contained herein or for incidental or
consequential damages in connection with furnishing, performance or use of this
material. We shall be under no liability in respect of any defect arising from fair
wear and tear, willful damage, negligence, abnormal working conditions, failure to
follow the instructions and warnings, or misuse or alteration or repair of the
products without written approval.
1
Table of Contents
1. INTRODUCTION……………………………………………………………………………….2~3
2.I NSTALLATION………………………………………………………………………………...4~5
3.SET UP FROM BAR CODE LABEL…………………………………………………….…..…..7
Transmission Speed…….………………………………………………..…………….…8
Wireless Auto-commection.…………………………………………………….……...8
Power-Saving Mode…………….…………………………………………………..…….8
Battery Fully Charged Alarm….…………………………………………………….….9
Low Battery Voltage Alarm….…………………………………………………….……9
Keyboard Country…….……….………………………………………………………….10
Multi-Interface Functions….…………………………………………………….…11~12
Symbologies On/Off………………………………………………………….....….13~15
Symbologies Set Up……………………………………………………………….…16~21
Edit Setup Bar Codes……………………………………….……………….…….……. 22
Macro/Special Keys Setup Bar Codes…………………………………….………...23
Termination String Setup Bar Codes………………………………………………..24
2
Introduction
3
Our 1D Wireless Laser barcode scanner combines the best scanning performance
and value. The device provides an accurate, easy, and fast method of data entry and
data storage for computerized information systems. It is easy to install and does not
require Software or drivers to operate.
Our Wireless Laser barcode scanner is a powerful and reliable handheld scanner
without compromise.
All the operating parameters are programmed by bar code programming menu and
stored in non-volatile RAM which can retain the settings after power is turned off.
4
Installation
Insert the plug on the free end of the Communications Cable into the appropriate
connector on the host as below described:
Cable Connection:
1. Please switch ON and charge scanner for 4~5 hours at first time before use,
scanner switch shown on Fig. 2.
2. After switch ON, the Orange LED will flash following with 3 beep-sounds. The
RED LED will be OFF while it links to cradle within 2.4GHz radio range.
3. If RED LED is continual ON, please re-plug USB cable, then, scan the 3 barcodes
on the bottom of cradle sequentially. (Shown on Fig. 3 from 1 to 3). If you are
unable to complete this setting within 1 minute, please re-plug USB cable &
re-start the scanner, and try again.
4. Charging issue: Cradle works as charger when putting scanner on it. Even if the
scanner's battery is full, the cradle will continue to supply power to the scanner.
We suggest you to remove scanner from cradle when scanner is charged fully.
5
Indicator Information
Orange continual ON Full charged
Orange LED Flash Charging / Low battery
Red LED ON Not read
Red LED Continual ON Off line / out of service
Green LED ON Good read
zWhen the battery voltage is too low, the Orange LED will flash and with one beep
sound. Please charge it immediately before the machine mandatorily shutdown. When
it shutdown, please full charge then repower on scanner.
zWhen OFF line/ out of service the 1D Engine will OFF and scanner will not work.
zUnder power-saving mode, there will not be LED indication
Reset Configuration to Defaults
If you are unsure of the scanner configuration or have scanned the incorrect
codes, please scan the following three barcodes. This will reset the scanner to
its factory defaults.
6
Tip
Do not hold the scanner directly over a barcode at 90˚. Scanning light bounces
directly back into the scanner from the barcode label is known as specular
reflection which will create a "dead zone" where decoding is difficult. Practice a
few times to find what range of angles works best.
Maintenance
Cleaning the scan window is the only maintenance required. A dirty window
may affect scanning accuracy.
Wipe the scanner window gently with a lens tissue or other material suitable for
cleaning optical material.
Do not spray water or other cleaning liquids directly onto the window.
7
Setup from Bar Code Label
8
T
ransmission Speed
High-speed transmission for PC uses.
Slow-speed transmission for PC use (Default).
Wireless Auto-connection
Wireless Auto-connection ON: When out of range, it
will keep trying to connect to device.
Wireless Auto-connection OFF: When out of range, it
will stop auto-connecting after sending signal for
connecting twenty times. When back to the range,
kindly presses trigger to connect to the device
(Default).
Powe
r
-Saving Mode
Power-Saving Mode can extend the usage time of battery. There are 5
modes can be chosen. When Scanner goes into Power-Saving Mode, user
can press "SCAN/Trigger" button, it will wake up and begin to scan.
Power-saving mode OFF
Enter power-saving mode after no usage
for 1 minute (Default)
Enter power-saving mode after no usage
for 5minute
Enter power-saving mode after no usage
for 15 minute
Enter power-saving mode after no usage
for 30 minute
zWhen in charging, scanner will not enter power-saving mode automatically.
Inhaltsverzeichnis
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
