Detnov CAD-250 Bedienungsanleitung
ENG
CONFIGURATION
GUIDE
ENG
ENG
2
3
ENG
ENG
4
Revision control
Revision Comment Date
a First edition. Software version 0.19.12 (27 Nov 2019) 09/04/2020
bUpdated layout. Software version 1.1.1. 16/06/2020
5
ENG
Before installing the CAD-250 control panel, you must check that a series of criteria are met.
If these criteria are not met, the control panel may be damaged, problems may arise during system start-up or the functioning of the system may be
lead to the warranty being voided.
Conditions of use
ENG
6
CONTENTS
1. INTRODUCTION............................................................................8
1.1.Disclaimer.................................................................................8
1.2.Standards and compliance .......................................................8
1.3. ..........................................................8
1.4.................................................................................8
1.5.About this manual.....................................................................9
1.6.Before getting started .............................................................10
1.7.Areas and zones.....................................................................11
2. VESTA SYSTEM ARCHITECTURE.............................................12
2.1.Loops and devices ................................................................12
2.2. .........................................................12
2.3.Alarm and control or manoeuvre outputs ...............................12
2.4.Panel ......................................................................................13
2.5.Nodes.....................................................................................13
3. INITIAL CONFIGURATION..........................................................14
3.1.User level................................................................................16
3.2...................................................................17
3.3.Main characteristics of the control panel ................................18
3.4.Main panel ..............................................................................18
3.5.General LEDs .........................................................................19
3.6.Primary controls......................................................................19
4. CONTROL PANEL CONFIGURATION .......................................20
4.1.Administrator access..............................................................20
4.2.Administrator screen ..............................................................21
7
ENG
7.4. ..................................................54
7.4.1.Description............................................................................................54
7.4.2.........................................54
7.4.3.Mode change in the sectorisation menu...............................................55
7.4.4.Test mode.............................................................................................55
7.4.5.Disabled mode......................................................................................55
8. MANOEUVRES ...........................................................................58
8.1.Main manoeuvres menu.........................................................59
8.2........................................................60
8.2.1.Inputs for manoeuvres, events. ......................................................61
8.2.2. ................................................................63
8.2.3.Outputs for the manoeuvres ...........................................................64
8.3.Group programming ...............................................................67
8.4.Virtual mode programming.....................................................70
8.5.Virtual module status..............................................................73
9. LOGS ...........................................................................................74
10. NETWORK .................................................................................78
10.1. ..........................................................78
10.2. ......................................................................80
11. FACILITY.....................................................................................82
11.1.Special modes......................................................................82
11.2. Two-step delay ....................................................................87
...............................................89
..................................................91
APPENDIX 1 ....................................................................................94
5. SETTINGS ...................................................................................22
5.1.General ..................................................................................22
5.1.1.Control panel description......................................................................22
5.1.2.Contact phone ......................................................................................23
5.1.3.Installer information ..............................................................................23
5.1.4.Language..............................................................................................23
5.1.5.Date selection.......................................................................................24
5.1.6.Screen settings.....................................................................................25
5.2.Versions .................................................................................26
5.2.1........................................................................................27
5.2.2.Installation from the USB port...............................................................28
5.3.Users......................................................................................30
5.4.Advanced ...............................................................................31
5.5.Connectivity............................................................................33
5.6.Printer.....................................................................................34
5.6.1.Printer options ......................................................................................34
5.6.2. ..................................................................34
5.7.Logs (event log) .....................................................................35
5.8.Test (display test) ...................................................................36
6. LOOP MENU................................................................................38
6.1.Devices ..................................................................................38
6.1.1. ....................................................40
6.2.Addressable value..................................................................42
6.3.Outputs...................................................................................44
6.4.Autosearch .............................................................................45
6.5.Autocheck ..............................................................................47
6.6............................................................48
6.7.Address programming............................................................49
7. SECTORISATION .......................................................................50
7.1 Sectorisation hierarchy and legacy mode ..............................50
7.2.Display controls......................................................................52
7.3.Filters .....................................................................................53
ENG
8
1. INTRODUCTION
1.1. DISCLAIMER
accept any responsibility for any misinterpretation of an instruction or
guidance note or for full system compliance.
The manufacturer's policy is of continuous improvement and we reserve
and without prior notice.
unit or the state of the detection wiring are not the responsibility of the
control panel manufacturer.
1.2. STANDARDS AND COMPLIANCE
The CE marking on this control panel indicates its compliance with
Directive Standard Description
2014/30/EU Electromagnetic Compatibility Directive
2014/35/EU Low Voltage Directive
305/2011/EU Construction Products Directive
EN54-2
EN54-4
1.3. REQUIRED DOCUMENTATION AND DESIGN
For the correct and complete installation, start-up, installation and
reference:
Document Description
MI 375 en 2020 CAD-250 control panel Installation Manual
MU 379 en 2020 CAD-250 control panel User Manual
MS 419 en 2020
Check that the manual version corresponds to the unit you are going
to install.
Detnov pays special attention to the compatibility of the components
compatibility notes between versions to ensure the greatest reliability
described in this manual refer to the date of this document and may
regulations and standards.
The most up-to-date information and the approvals for this are available
on our website www.DETNOV.com.
1.4. EXPLICIT DEFINITIONS
The procedures described in this manual include warnings and cautions
to advise the user to adopt methodical and safe working practices
Please heed the warnings in this manual, as incorrect use or improper
9
ENG
These warnings alert you to serious risks or precautions to consider
regulatory references or advice for facilitating the assembly, connection
or installation processes are not followed.
Word Denition
⚠WARNING! Risk of personal injury
Risk for the product and system
EN
UNE
ISO
Check according to the applicable regulations
There is no risk and no observations or comments
to facilitate the action
Go to the technical support service
Recommended action
Action not recommended or incorrect
1.5. ABOUT THIS MANUAL
minimum understanding of the system menus, with all kinds of
descriptions regarding procedures and technical details necessary for
and alarm system.
For each step in the process, a detailed description is included with
drawings, diagrams and charts, making these instructions easier to
understand.
The accuracy of the contents of this manual is the most important
manufacturer reserves the right to change the information without prior
notice.
The advanced graphical interface of the CAD-250 control panel allows
used by the start-up engineer.
ENG
10
1.6. BEFORE GETTING STARTED
must be organised and grouped so that both the detection of a potential
The speed of the response and with which action is taken is essential
for safeguarding people and minimising damage to the facilities.
Andere Handbücher für CAD-250
2
Inhaltsverzeichnis
Andere Detnov Bedienfeld Handbücher
