Devolo MT 02648 Bedienungsanleitung

Devolo home Control Door/Window

Contact MT 02648

The Door/Window Contact and the Motion Detector have two additional

functions integrated: temperature and illumination measurement, based

on Z-WaveTM technolog .

It is the Z-WaveTM plus product, it support the securit , OTA... Those

newest features of the Z-WaveTM technolog . Z-WaveTM is a wireless

communication protocol designed for home automation, specificall to

remotel control applications in residential and light commercial

environments. The technolog uses a low-power RF radio embedded or

retrofitted into home electronics devices and s stems, such as lighting,

home access control, entertainment s stems and household appliances.

The product can be included and operated in an Z-WaveTM network

with other Z-WaveTM certified devices from other manufacturers and/or

other applications. All non-batter operated nodes within the network

will act as repeaters regardless of vendor to increase reliabilit of the

network.

The device adopt the Z-WaveTM 500 series chip, when our Z-WaveTM

network s stem is all made b Z-WaveTM 500 series devices. The

network s stem will have the advantages as below.

•Concurrent multi-channel support reduces external interference.

•Better RF range, improve about 10 meters in indoor.

•Support 100 Kbps transmit speed, speed up communication.

Function Compare A/B/C

PIR Door/Window Temperature Illumination

Motion

Sensor

MT 02647

V V V

Door/Window

Contact

MT 02648

VVV

Add to/ emove from Z-WaveTM Network

There are two tamper ke s in the device, one is in the back side,

another is in the front side. Both of them can add, remove, reset or

association from Z-WaveTM network.

In the first time, add the device into the Z-WaveTM network. First, make

sure the primar controller is in the add mode. And then power on the

device, just take out the insulation M lar in the back side of the device.

The device will auto start the NWI (Network Wide Inclusion) mode. And

it should be included in 5 seconds. You will see the LED light ON one

second.

Notice: Including a node ID allocated b Z-WaveTM Controller means

“Add” or “Inclusion”. Excluding a node ID allocated b Z-WaveTM

Controller means “ emove” or “Exclusion”.

Function Description

Add

1. Have Z-WaveTM Controller entered inclusion mode.

2. Pressing tamper ke three times within 1.5 seconds

to enter the inclusion mode.

3. After inclusion successful, the device will wake to

receive the setting command from Z-WaveTM

Controller about 20 seconds.

Remove

1. Have Z-WaveTM Controller entered exclusion mode.

2. Pressing tamper ke three times within 1.5 seconds

to enter the exclusion mode.

Node ID has been excluded.

Reset

Notice: Use this procedure only in the event

that the primary controller is lost or

otherwise inoperable.

1. Pressing tamper ke four times within 1.5 seconds

and do not release the tamper ke in the 4th

pressed, and the LED will light ON.

2. After 3 seconds the LED will turn OFF, after that

within 2 seconds, release the tamper ke . If

successful, the LED will light ON one second.

Otherwise, the LED will flash once.

3. IDs are excluded and all settings will reset to

factor default.

Association 1. Have Z-WaveTM Controller entered association

mode.

2. Pressing tamper ke three times within 1.5 seconds

to enter the association mode.

Note: The device support 2 groups. The group 1 is for

receiving the report message, like triggered event,

temperature, illumination etc. The group 2 is for light

control, the device will send the “Basic Set” command

to this group. And each group support 8 nodes

maximum.

•Failed or success in including/excluding the node ID can be

viewed from Z-WaveTM Controller.

Notice 1: Alwa s RESET a Z-WaveTM device before tr ing to add it to a

Z-WaveTM network

Notice 2: When the device into NWI mode, the sensor functionalit

will useless. The NWI mode will timeout after 30 seconds. You can

press the tamper ke 3 times to abort the NWI mode.

Z-WaveTM Notification

After the device adding to the network, it will wake-up once per da in

default. When it wake-up it will broadcast the “Wake Up Notification”

message to the network, and wake-up 10 seconds for receive the

setting commands.

The wake-up interval minimum setting is 30 minutes, and maximum

setting is 120 hours. And the interval step is 30 minutes.

If the user want to wake-up the device immediatel , please remove the

front cover, and press the tamper ke once. The device will wake-up 10

seconds.

Z-WaveTM Message eport

When the Motion Detector triggered or the Door/Window Contact

triggered, the device will report the trigger event and also report the

batter status, temperature and illumination level.

In default the device will using Notification Report to represent the

trigger event, it can be changed to Sensor Binar Report b setting the

configuration NO. 7 Bit4 to 1.

* Motion eport:

When the Motion Detector detected, the device will unsolicited to send

the report to the nodes in the group 1.

Notification Report (V4)

Notification T pe: Home Securit (0x07)

Event: Motion Detection, Unknown Location (0x08)

Sensor Binar Report (V2)

Sensor T pe: Motion (0x0C)

Sensor Value: 0xFF

* Door/Window eport:

When the door/window state changed, the device will unsolicited to

send the report to the nodes in the group 1.

Notification Report (V4)

Notification T pe: Access Control (0x06)

Event: Door/Window is open (0x16)

Door/Window is closed (0x17)

Sensor Binar Report (V2)

Sensor T pe: Door/Window (0x0A)

Sensor Value: 0x00 is closed, 0xFF is opened.

* Tamper eport:

Both the 2 tamper ke s are pressed over 5 seconds. The device will

into the alarm state. In that state, if an one of the tamper ke s be

released, the device will unsolicited to send the report to the nodes in

the group 1.

Notification Report (V4)

Notification T pe: Home Securit (0x07)

Event: Tampering. Product covering removed (0x03)

Sensor Binar Report (V2)

Sensor T pe: Tamper (0x08)

Sensor Value: 0xFF

* Temperature eport:

When the Motion Detector detected or the Door/Window Contact state

changed, the device will unsolicited to send the “Sensor Multilevel

Report” to the nodes in the group 1.

Sensor T pe: Temperature (0x01)

Note: To disable this functionalit b setting the configuration N0.5 bit5

to 1.

*** Temperature differential report ***

This function default is enabled, to disable this function b setting the

configuration NO.21 to 0.

In the default, when the temperature is changed to plus or minus one

degree Fahrenheit (0.56 degree Celsius), the device will report

temperature information to the nodes in the group 1.

The device will measure the temperature in ever one minute. And if

the temperature is over 140 degree Fahrenheit (60 degree Celsius), the

device will alwa s report in each measurement.

Caution 1:

Enable this functionalit , it will cause the PIR Motion to

disable detection when the temperature measurement. In other words,

The PIR motion will blind one second in ever one minute.

* Illumination eport:

When the Motion Detector detected or the Door/Window Contact state

changed, the device will unsolicited to send the “Sensor Multilevel

Report” to the nodes in the group 1.

Sensor T pe: Luminance (0x03)

Note: To disable this functionalit b setting the configuration N0.5

bit4 to 1.

*** Illumination differential report ***

This function default is disabled, to enable this function b setting the

configuration NO.22 not to zero.

Enable this functionalit , the device will measure the illumination in

ever one minute. And if the illumination is changed to plus or minus

the value (setting b the configuration NO.22), the device will report

illumination information to the nodes in the group 1.

Caution 1:

Enable this function will reduce the batter life about 15%

~ 20%. And another issue is setting the differential value too small, it

will cause report too frequenc , shorter the batter life more.

Propose the setting differential value should not small than 10.

Caution 2:

If the configuration No.4 is setting to 0 or 100, this

functionalit is useless.

Caution 3:

Enable this functionalit , it will cause the Motion Detector

to disable detection when the illumination measurement. In other

words, The Motion Detector will blind one second in ever one minute.

* Timing eport:

Beside the event triggered could report message, the device also

support the timing unsolicited report of the status.

•Batter level report: Ever 6 hours report once in default.

It could be changed b setting the configuration NO. 10.

•Low batter report: When the batter level is too low, ever 30

minutes will report once.

•Door/window state report: Ever 6 hours report once in default.

It could be changed b setting the configuration NO. 11.

•Illumination level report: Ever 6 hours report once in default.

It could be changed b setting the configuration NO. 12.

•Temperature report: Ever 6 hours report once in default.

It could be changed b setting the configuration NO. 13.

Notice: The configuration NO. 10, 11, 12 and 13 could be setting to

zero to disable the auto report. And the configuration NO. 20 could

change the tick interval, the default value is 30, if setting to 1, that

means the minimum auto report interval will be one minute. And please

notice if setting this value to zero, that means disable all of the timing

report except the low batter detection.

Power Up Procedure

* Battery Power Check

When the device power up, the device will detect the power level of the

batter immediatel . If the power level is too low, the LED will continue

flash about 5 seconds. Please change another new batter .

* Motion Detector Warm Up

When the device power on, the Motion Detector need to warm up

before the operation. The warm up time about 1 minute, the LED will

flash in ever 2 seconds. After finish the procedure the LED will light

ON three times.

* NWI

When the device power on, the device will check is it alread adding to

the network? If doesn't, it will auto start the NWI mode. The LED will

flash in ever second and continue 30 seconds. Until timeout or the

device successful to inclusion b controller. The use can presses the

tamper ke 3 times to abort the NWI mode.

* Wake

When the device power on, the device will wake about 20 seconds. In

this duration, the controller can communicate with the device. Normall

the device is alwa s sleeping to save the batter energ .

Over The Air (OTA) Firmware Update

The device support the Z-Wave firmware update via OTA.

Before starting the procedure, please remove the front cover of the

device. Otherwise the hardware check will be failed.

Let the controller into the firmware update mode, and then press the

front tamper ke once to start the update.

After finish the firmware download, the LED will start flash in ever 0.5

second. At that time,

please don't remove the battery

, otherwise it

will cause the firmware broken, and the device will no function.

After the LED stop flash, it is recommended that the user power up the

device. Caution: After remove the batter , please wait about 30

seconds, and then re-install the batter .

Security Network

The device support the securit function. When the device included

with a securit controller, the device will auto switch to the securit

mode. In the securit mode, the follow commands need using Securit

CC wrapped to communicate, otherwise it will not response.

COMMAND_CLASS_BATTERY

COMMAND_CLASS_NOTIFICATION_V4

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_SENSOR_BINARY_V2

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

COMMAND_CLASS_WAKE_UP_V2

Function DIP Switch(Motion Sensor only)

There is one function DIP switch in front of the device.

Remove the front cover in the right top of the PCB, and also has mark

“M1” and “M2” for two switch.

M1 M2 Description

ON ON Test Mode and OTA mode.

ON OFF Normal Mode.

OFF ON Normal Mode.

OFF OFF Program Mode. According to the configuration setting

NO. 5 to set the operation mode.

Operation Mode

There are two modes “Test” and “Normal”.

“Test Mode” is for the user test the sensor function when installation.

“Normal Mode” for the normal operation.

When the event triggered, normall the LED won't indicated, unless the

batter is in the low level, the LED will flash once. But in the “Test

Mode” the LED also will light ON one second.

When the event triggered, the device will report the messages to the

nodes in the group 1. The messages also include the batter level, the

temperature and the illumination level. The user can switch the report

b setting the configuration NO. 5 bit4 (illumination) and bit5

(temperature), and the configuration NO. 7 bit6 (batter ).

When the event triggered, if the environment luminance is less than

the setting of the value of the configuration NO. 4, the device will emit

the signal to turn ON the lighting equipment, those nodes are in the

group 2. And dela a while to turn OFF the lighting equipment. The

dela time is setting b the configuration NO. 9.

The PIR motion re-detected interval, in the “Test Mode” fixed to 6

seconds. In the “Normal Mode”, it according to the setting of the

configuration NO. 8.

Notice: When the tamper ke of the back side is released, the device

alwa s in the “Test Mode”, no matter the DIP switch setting.

Battery Installation

When the device report the low batter message. The user should

replace the batter to new one. The batter t pe is CR123A, 3.0V.

The wa to open the front cover please follow below steps.

1. Using a tool to press the 1-1 position, to release the cover.

2. Hold the front cover and pull back

3. Hold the front cover and pull up

Replace the new batter and install the cover back.

1. Put the front cover bottom to 1-1, and press down.

2. Push the front cover top to 2-1.

Choosing a Suitable Location

1. The recommended mounting height is 160cm

2. Don't let the device facing the window or the sunlight.

3. Don't let the device facing the source of heat. For instance the

heater or the air-condition.

Installation

1. In the first time, add the device into the Z-WaveTM network. First,

make sure the primar controller is in the inclusion mode. And then

power on the device, just take out the insulation M lar in the back side

of the device. The device will auto start the NWI (Network Wide

Inclusion) mode. And it should be included in 5 seconds. You will see

the LED light ON one second.

2. Let the controller associate with the device into the first group, an

light switch that intend to be turned on when the device trig please

associate with the device into the second group.

After finish the test and decide to fix, then ou can remove tape A, and

mounting the sensor b using tape B. The tamper ke will pressed and

let the sensor enter normal mode.

Z-Wave Configuration Settings

Notice:

* All of the configuration, the data size is 1.

* The configuration mark with star(*), means after the exclusion the

setting still keep, don't reset to factor default. Unless the user execute the

“RESET” procedure.

NO. Name Def. Valid A B C Description

2Basic Set

Level 0xFF All   

Setting the BASIC command value to

turn on the light. The 0xFF(-1) means

turn on the light. For dimmer

equipment 1 to 100 means the light

strength.

0 means turn off the light.

(*)

PIR

Sensitivit 80 0 ~

99   

PIR sensitivit settings.

0 means disable the PIR motion.

1 means the lowest sensitivit ,

99 means the highest sensitivit .

High sensitivit means can detected

long distance, but if there is more

noise signal in the environment, it will

re-trigger too frequenc .

4Light

Threshold 99 0 ~

100   

Setting the illumination threshold to

turn on the light. When the event

triggered and the environment

illumination lower then the threshold,

the device will turn on the light.

0 means turn off illumination detected

function. And never turn on the light.

1 means darkest.

99 means brightest.

100 means turn off illumination

detected function. And alwa s turn on

the light.

Notice: In none test mode, onl the

value in 1 to 99 will enable the

illumination detected function and

update the illumination value.

NO. Name Def. Valid A B C Description

(*)

Operation

Mode

0All Operation mode. Using bit to control.

0Bit0: Reserve.

0  

Bit1: 1 means enable test mode,

0 means disable normal mode.

Notice:

This bit onl effect b the DIP Switch

setting to program mode.

0Bit2: Disable the door/window

function.

0Bit3: Setting the temperature scale.

0: Fahrenheit, 1:Celsius

0Bit4: Disable the illumination report

after event triggered.

0Bit5: Disable the temperature report

after event triggered.

0Bit6: Reserve.

0Bit7: Disable the back ke release

into test mode.

NO. Name Def. Valid A B C Description

(*)

Mult-

Sensor

Function

Switch

4All Multisensor function switch. Using bit

to control.

0Bit0: Disable magnetic integrate

illumination.

0Bit1: Disable PIR integrate

Illumination.

1Bit2: Disable magnetic integrate PIR

(Default is Disable)

0  

Bit3: When Bit2 is 0 (Enable), Are the

device and the lighting in the same

room?

0: In the same room(Default),

1: In the different room.

Notice: If this bit is 1, it is

recommended also set the Bit1 to 1,

cause the PIR triggered, doesn't

mean the people in that room.

0Bit4: Disable dela 5 seconds to turn

off the light, when door/window

closed.

0  

Bit5: Disable auto turn off the light,

after door/window opened to turn on

the light.

Notice: If bit2 is zero, this setting is

useless.

Notice: If the configuration No.9 is

zero, this setting is useless.

0Bit6: Reserve.

0Bit7: Reserve.

NO. Name Def. Valid A B C Description

(*)

Customer

Function

4All Customer function switch, using bit

control.

0Bit0: Reserve.

0  

Bit1: Enable sending motion OFF

report.

Note: Depends on the Bit4,

0: Report Notification CC,

T pe: 0x07, Event: 0xFE

1: Sensor Binar Report,

T pe: 0x0C, Value: 0x00

1Bit2: Enable PIR super sensitivit

mode.

0Bit3: Enable don't send out BASIC

OFF after door closed.

0Bit4: Notification T pe,

0: Using Notification Report.

1: Using Sensor Binar Report.

0Bit5: Disable Multi CC in auto report.

0Bit6: Disable to report batter state

when the device triggered.

0Bit7: Reserve.

NO. Name Def. Valid A B C Description

Inhaltsverzeichnis

Andere Devolo Sicherheitssensor Handbücher

Devolo

Devolo Home Control Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung