DeWalt DXSTFB048 Bedienungsanleitung

IMPORTANT:

Please read this manual carefully before assembling this

garage bench and save it for reference

DXSTFB048

GARAGE BENCH

INSTRUCTION

MANUAL

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating

instructions. Read all instructions and follow them with

use of this product.

TABLE OF CONTENTS

TECHNICAL SPECIFICATIONS 4

SAFETY GUIDELINES 5

PARTS LIST 6

ASSEMBLY 8

WARRANTY 11

TABLE OF CONTENTS

DXSTFB048

TECHNICAL SPECIFICATIONS

SEAT CAPACITY 1,000 lb (454 kg)

*WHEN WEIGHT IS EVENLY DISTRIBUTED

SHELF CAPACITY 1,500 lb (680 kg)

*WHEN WEIGHT IS EVENLY DISTRIBUTED

HEIGHT 19.75" (50.16 cm)

WIDTH 49.6" (126 cm)

DEPTH 15" (38.1 cm)

WEIGHT 48 lb (21.77 kg)

TECHNICAL SPECIFICATIONS

SAFETY GUIDELINES

• Save all warnings and instructions for future reference.

• This manual contains important safety and assembly

instructions. Read all instructions and follow them with

the use of this product.

FPO

GENERAL SAFETY

• Keep work area clean and dry.

• Use correct/recommended tools for the job.

• Never leave unattended tools plugged in or running.

• Never force a part into place.

• Wear appropriate safety apparel for the job you are doing.

• Wear safety glasses/goggles.

• Keep small parts away from children. Never leave a small child unattended while assembling.

• Always use common sense – your personal safety is your responsibility.

NEVER EXCEED THE FOLLOWING WEIGHT LIMITS FOR THIS BENCH

• Maximum load for bench seat: Up to 1,000 lb (454 kg) when weight is evenly distributed.

• Maximum load for shelf: Up to 1,500 lb (680 kg) when weight is evenly distributed.

• It is recommended that the heaviest load be placed on the bottom shelf.

DXSTFB048

PARTS LIST

No. Description

1 Cushion Seat

2 Pre-Bolted Upright Assembly

3 Wire Deck

4 Crossbeam

5Bench Top Support Strap (Black)

6Recessed Shelf Support Strap (Yellow)

No. Description

7 Safety Strap With Weld Nut

8 Safety Strap Bolt

9 Locking Shelf Pin

10 4 mm Hex Key

11 4 mm Hex Bit

12 Locking Grid Clip

BEFORE YOU BEGIN:

• Read all instructions thoroughly.

• Remove all components from the box, and lay them on the floor in an orderly fashion.

• Wear eye protection.

• Be cautious of sharp edges.

• Keep this information for further reference.

FPO

Qty. Qty.

PARTS LIST

Tools Required for Bench Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included);

Rubber Mallet (not included), Flat-Head Screwdriver (not included)

DXSTFB048

ASSEMBLY

CROSSBEAM INSTRUCTIONS

• Note: It is recommended for one person to hold the

pre-assembled upright frames in place while a second person

installs the crossbeams.

• Note: Keep the bolt heads of the diagonal pieces of the uprights

on the outside of the assembly (*see first image).

• Note: The top crossbeams have 4 slots for their associated

bench support straps, and the bottom crossbeams have 3

slots for their associated support straps.

STEP 1

• There is a set of locking tabs at both ends of every crossbeam.

To begin assembly, take a crossbeam with 3 slots and insert

the tabs into two of the holes on the lower portion of one

upright frame. Engage the locking tabs into the holes using

a downward motion. The locking bolt hole should be at the

top. Make sure the end of the crossbeam is flush against the

upright frame.

STEP 2

• Repeat for the opposite side of the upright frame. Tap the ends

of the crossbeam closest to the upright frames with a rubber

mallet until fully seated. The crossbeam and locking tabs

should easily slip into place. If they do not, then recheck the

alignment of the teardrop-shaped holes and tabs. Too much

force may damage the interlock between the crossbeam and

upright frame.

STEP 3

• Using the methods listed above, install the other crossbeam

with 3 slots to the opposite side of the upright frames,

parallel to the first crossbeam you installed. Make sure both

crossbeams are at the same level.

STEP 4

• Continue by installing the top sets of crossbeams flush to the

top of the upright frames (each top crossbeam has 4 slots and

one will have the DEWALT®badge on the far right). Make sure

the crossbeams are attached at the same level on both sides.

LOCKING

PIN HOLE

UPRIGHT

FRAME

*KEEP BOLT

HEADS OF

DIAGONAL

PIECE ON

OUTSIDE OF

ASSEMBLY

• Note: There are two (2) safety straps with weld nuts and

three (3) recessed shelf support straps on the bottom set

of crossbeams.

• Note: There are two (2) safety straps with weld nuts and

four (4) bench top support straps on the top set

of crossbeams.

• Note: Top and bottom crossbeams use different support straps.

STEP 1

• Starting with the bottom set of crossbeams, place a safety

strap with weld nut between the lower ridges of the crossbeams

where two sets of holes have been pre-drilled. Thread a safety

strap bolt up through the bottom of the pre-drilled holes and

through the weld nuts, and fully tighten with the included

hex key or drill bit. Repeat for the second strap on this set of

crossbeams, and continue for the last 3 straps.

STEP 2

• On the bottom of the bench, place a recessed shelf support

strap (yellow) perpendicular to the bottom crossbeams,

and insert each end into the channel on each ridge of the

crossbeam. Repeat for the remaining 2 (yellow) straps.

STEP 3

• On the top of the bench, place a bench top support strap

(black) perpendicular to the top crossbeams, and insert each

end into the channel on each ridge of the crossbeam. Repeat

for the remaining 3 (black) straps.

SAFETY STRAP AND SUPPORT STRAP INSTRUCTIONS

BENCH TOP

SUPPORT STRAPS (BLACK)

RECESSED SHELF

SUPPORT STRAPS

(YELLOW)

SAFETY STRAP

WITH WELD NUT

SAFETY STRAP

WITH WELD NUT

CROSSBEAM

RECESSED SHELF

SUPPORT STRAPS ON

BOTTOM CROSSBEAMS

TOP BENCH

SUPPORT STRAPS ON

TOP CROSSBEAMS

DXSTFH048

ASSEMBLY

WIRE GRID AND LOCKING SHELF PIN INSTRUCTIONS

• Note: The wire grid consists of two sides – a “short” side

and “long” side. If you plan on sliding objects on and off of

the shelf from the front of the bench, then we recommend

having the “short” side of the grid facing upward. If you

plan on sliding objects from the side of the bench , then we

recommend having the “long” side facing upward.

STEP 1

• Place the wire grid onto the top ridge of the lower set of

crossbeams. If seated properly, the grids will “pop” into place

and lay evenly.

STEP 2

• Place a locking grid clip at the outermost corner of the shelf.

Make sure the rolled edge with the groove is facing upwards.

STEP 3

• With one hand, apply pressure to the back of the clip. With

your free hand, insert a flat-head screwdriver (not included)

into the small slot in the clip to spread the tine up and over the

wire that is underneath.

STEP 4

• Pull back on the screwdriver. The grooved channel in the clip

should now match up with the wire decking, which will help

secure it to the shelf beam.

STEP 5

• Repeat Steps 2-4 for the remaining three corners of the wire grid.

STEP 6

• There is a locking pin hole at both ends of every crossbeam.

This is where the locking shelf pins are to be installed. If a pin

does not easily slip into place, then moderately tap the end of

the crossbeam to fully seat the locking tabs.

FPO

LOCKING GRID

CLIP

LOCKING

SHELF PIN INTO

LOCKING PIN

HOLE ON

CROSSBEAM

Andere Handbücher für DXSTFB048

Inhaltsverzeichnis

Andere DeWalt Inneneinrichtung Handbücher

DeWalt

DeWalt DXST10000BLK Bedienungsanleitung

DeWalt

DeWalt DXST4500 Bedienungsanleitung

DeWalt

DeWalt DXSTFB048 Bedienungsanleitung

DeWalt

DeWalt DXST4500 Bedienungsanleitung

DeWalt

DeWalt DXST4500BLK-W Bedienungsanleitung

DeWalt

DeWalt DXSTAH025 Bedienungsanleitung

DeWalt

DeWalt DXSTFH030 Bedienungsanleitung

DeWalt

DeWalt DXST4500BLK Bedienungsanleitung

DeWalt

DeWalt DXSTFH030 Bedienungsanleitung

DeWalt

DeWalt DXSTAH025 Bedienungsanleitung

DeWalt

DeWalt DXSTAH025 Bedienungsanleitung

DeWalt

DeWalt DXSTAH025 Bedienungsanleitung

DeWalt

DeWalt DXST4500-W Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung