DeWalt DW325PT Bedienungsanleitung

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D



DW325PT

30° Paper Tape Framing Nailer

Clouese à Charpente de 30° pour ruban de papier

Clavadora Estructural de 30° Para Cinta De Papel

DW325PL

21° Plastic Collated Framing Nailer

Clouese à charpentede 21° en plastique

Clavadora Para Moarcos de 21° Con Unión de Plástico

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 1 11/14/14 3:06 PM

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 2 11/14/14 3:06 PM

BEFORE OPERATING THIS TOOL, CAREFULLY READ AND

UNDERSTAND ALL INSTRUCTIONS IN THE IMPORTANT

SAFETY INSTRUCTIONS SECTION.



The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

WALT

(1-800-433-9258)







WARNING: Do not operate this unit until you read this instruction

manual for safety, operation and maintenance instructions.

WARNING: This product contains chemicals known to the State

of California to cause cancer, and birth defects or other reproductive

harm. Wash hands after handling.

WARNING: Some dust contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm such

as asbestos and lead in lead based paint.

• Actuating tool may result in flying Fig. A

FIG. B

FIG. C

FIG. D

debris, collation material, or dust

which could harm operator’s eyes.

The operator and all those persons in the

general area should wear safety glasses

with permanently attached side shields.

Approved safety glasses are imprinted

with the characters “Z87.1”. It is the

employer’s responsibility to enforce the

use of eye protection equipment by the

tool operator and other people in the work

area. (Fig. A)

• Always wear appropriate personal

hearing and other protection during

use. Under some conditions and duration

of use, noise from this product may

contribute to hearing loss. (Fig. A)

• Use only clean, dry, regulated air.

Condensation from an air compressor can

rust and damage the internal workings of

the tool. (Fig. B)

• Regulate air pressure. Use air

pressure compatible with ratings on

the nameplate of the tool. (Not to

exceed 120 psi, 8.3 bar) Do not connect

the tool to a compressor rated at over

200 psi. The tool operating pressure must

never exceed 200 psi even in the event of

regulator failure. (Fig. C)

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 1 11/14/14 3:06 PM

• Only use air hose that is rated for a maximum working

pressure of at least 150 PSI (10.3 BAR) or 150% of the

maximumsystempressure,whicheverisgreater. (Fig. D)

• Donotusebottledgasestopowerthis FIG. E

FIG. F

FIG. G

tool. Bottled compressed gases such as

oxygen, carbon dioxide, nitrogen,

hydrogen, propane, acetylene or air are

not for use with pneumatic tools. Never

use combustible gases or any other

reactive gas as a power source for this tool.

Danger of explosion and/or serious

personal injury may result. (Fig. E)

• Usecouplingsthatrelieveallpressure

from the tool when it is disconnected

from the power supply. Use hose

connectors that shut off air supply from

compressor when the tool is disconnected.

(Fig. F)

• Disconnecttoolfromairsupplywhen

not in use. Always disconnect tool

from air supply and remove fasteners

from magazine before leaving the

area or passing the tool to another

operator. Do not carry tool to another

workareainwhichchanginglocation

involves the use of scaffoldings, stairs,

ladders, and the like, with air supply

connected.Donotmakeadjustments,

remove magazine, perform maintenance or clear jammed

fasteners while connected to the air supply. If the contact trip is

adjusted when the tool is connected to the air supply and nails are

loaded, accidental discharge may occur. (Fig. G)

• Connect tool to air supply before loading fasteners, to

prevent a fastener from being fired during connection. The

tool driving mechanism may cycle when tool is connected to

the air supply. Do not load fasteners with trigger or contact trip

depressed, to prevent unintentional firing of a fastener.

• Do not remove, tamper with, or FIG. H

FIG. I

FIG. J

otherwise cause the tool, trigger, or

contact trip to become inoperable.

Do not tape or tie trigger or contact trip in

the on position. Do not remove spring

from contact trip. Make daily inspections

for free movement of trigger and contact

trip. Uncontrolled discharge could result.

• Inspect tool before use. Do not

operate a tool if any portion of the tool,

trigger, or contact trip is inoperable,

disconnected,altered,ornotworking

properly. Leaking air, damaged parts

or missing parts should be repaired or

replaced before use. (Fig.H)

• Donotalterormodifythetoolinany

way. (Fig. I)

• Alwaysassumethatthetoolcontains

fasteners.

• Do not point the tool at co-workers

or yourself at any time. No horseplay!

Work safe! Respect the tool as a working

implement. (Fig. J)

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 2 11/14/14 3:06 PM

• Keepbystanders,children,andvisitorsawaywhileoperating

a power tool. Distractions can cause you to lose control. When

tool is not in use, it should be locked in a safe place, out of the

reach of children.

• Remove finger from trigger when not driving fasteners.

Never carry tool with finger on trigger.

Accidental discharge could result. Using

the trigger lock-off will prevent accidental

discharge.

• Do not overreach. Maintain proper

footing and balance at all times. Loss of

balance may cause cause personal injury.

(Fig. K)

• Makesurehoseisfreeofobstructions

or snags. Entangled or snarled hoses

can cause loss of balance or footing.

• Usethetoolonlyforitsintendeduse.

Do not discharge fasteners into open

air, concrete, stone, extremely hard

woods, knots or any material too

hard for the fastener to penetrate.

Do not use the body of the tool or top

cap as a hammer. Discharged fasteners

may follow unexpected path and cause

injury. (Fig. L)

• Alwayskeepfingersclearofcontact

trip to prevent injury from inadvertent

release of nails. (Fig. M)

• RefertotheMaintenance and Repairs

sections for detailed information on

the proper maintenance of the tool

• Always operate the tool in a clean,

FIG. P

FIG. N

FIG. O

lighted area. Be sure the work surface

is clear of any debris and be careful not

to lose footing when working in elevated

environments such as rooftops.

• Do not drive fasteners near edge

of material. The workpiece may split

causing the fastener to ricochet, injuring

you or a co-worker. Be aware that the nail

may follow the grain of the wood (shiner),

causing it to protrude unexpectedly from

the side of the work material. Drive the

nail perpendicular to the grain to reduce

risk of injury. (Fig. N)

• Do not drive nails onto the heads

of other fasteners or with the tool

at too steep an angle. Personal injury

from strong recoil, jammed fasteners, or

ricocheted nails may result. (Fig. O)

• Beawareofmaterialthicknesswhen

using the nailer. A protruding nail may

cause injury.

• Beawarethatwhenthetoolisbeing

utilized at pressures on the high end

of its operating range, nails can be

driven completely through thin or

very soft work material. Make sure

the pressure in the compressor is set so

that nails are set into the material and not

pushed completely through. (Fig. P)

FIG. K

FIG. L

FIG. M

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 3 11/14/14 3:06 PM

• Keephandsandbodypartsclearof FIG. Q

Fig. R

FIG. S

immediateworkarea. Hold workpiece

with clamps when necessary to keep

hands and body out of potential harm. Be

sure the workpiece is properly secured

before pressing the nailer against the

material. The contact trip may cause the

work material to shift unexpectedly.

(Fig.Q)

• Do not use tool in the presence of

flammable dust, gases or fumes. The

tool may produce a spark that could

ignite gases causing a fire. Driving a nail

into another nail may also cause a spark.

(Fig.R)

• Keepfaceandbodypartsawayfrom

back of the tool cap when working

in restricted areas. Sudden recoil can

result in impact to the body, especially

when nailing into hard or dense material.

(Fig. S)

• Grip tool firmly to maintain control

while allowing tool to recoil away

from work surface as fastener is

driven. In “Contact Actuation Mode” if

contact trip is allowed to recontact work

surface before trigger is released an

unwanted fastener will be fired.

• Choice of triggering method is

important. Check the manual for triggering options.

CONTACT ACTION TRIGGER

• Whenusingthecontactactiontrigger,

FIG. T

be careful of unintentional double

fires resulting from tool recoil.

Unwanted fasteners may be driven if

the contact trip is allowed to accidentally

re-contact the work surface. (Fig. T)

TO AVOID DOUBLE FIRES:

 • Donot engagethetoolagainst the

work surface with a strong force.

 • Allowthetooltorecoilfullyaftereachactuation.

 • Usesequentialactiontrigger.

• When “contact” actuating the framing nailer, always

keeptoolincontrol. Inaccurate placement of tool can result

in misdirected discharge of a fastener.

SEQUENTIAL ACTION TRIGGER

• Whenusingthesequentialaction FIG. U

trigger, do not actuate the tool

unless the tool is placed firmly

againsttheworkpiece.

• Donotdrivenailsblindly into walls,

floorsorotherworkareas.Fasteners

driven into live electrical wires, plumbing,

or other types of obstructions can result

in injury. (Fig.U)

• Stay alert, watch what you are

doing and use common sense when

operating a power tool. Do not use tool while tired or under

the influence of drugs, alcohol, or medication. A moment

of inattention while operating power tools may result in serious

personal injury.

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 4 11/14/14 3:06 PM

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• leadfromlead-basedpaints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenicandchromiumfromchemically-treatedlumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday

eyeglassesareNOTsafetyglasses.Alsousefaceordustmask

if operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSIZ87.1eyeprotection(CAN/CSA/Z94.3),

• ANSIS12.6(S3.19)hearingprotection,

• NIOSH/OSHA/MSHArespiratoryprotection.







A. Trigger

B. Exhaust

C. Rafter hook

D. Contact trip

E. Pusher

F. Magazine

FIG. 1

DW325PL

DW325PT

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 5 11/14/14 3:06 PM



MODEL DW325PT DW325PL

HEIGHT 12.5" (305 mm) 12.5" (305 mm)

WIDTH 4.75" (121 mm) 4.75" (121 mm)

LENGTH 17.5" (444 mm) 17.5" (444 mm)

WEIGHT 7.6 lb (3.45 kg) 7.6 lb (3.45 kg)

MAGAZINE ANGLE 30° 21°

RECOMMENDED

OPERATING PRESSURE

70 - 120 psig 70 - 120 psig

AIR CONSUMPTION PER

100 CYCLES

7.5 cfm @ 80 psi 7.5 cfm @ 80 psi

LOADING CAPACITY

Up to 92 Nails Up to 64 Nails



MODEL DW325PT DW325PL

NAIL LENGTHS 2" - 3-1/4"

(50 mm - 83 mm) 2" - 3-1/4"

(50 mm - 83 mm)

SHANK DIAMETERS .113" - .131"

(2.8 mm - 3.3 mm) .113" - .148"

(2.8 mm - 3.7 mm)

FASTENER COLLATION 30° - 34°

Paper tape 21° Plastic

collated

NAIL TYPE 30° clipped head/

30° full head 21° round head





WARNING: Read the section titled Important Safety Instructions

at the beginning of this manual. Always wear eye and ear protection

when operating this tool. Keep the nailer pointed away from yourself

and others. For safe operation, complete the following procedures

and checks before each use of the nailer.

1. Before you use the nailer, be sure that the compressor tanks

have been properly drained.

2. Lubricate the tool following these directions:

a. Use D

WALT pneumatic tool oil or a non-detergent S.A.E. 20

weight oil. DO NOT use detergent oil or additives as they will

damage o-rings and rubber parts.

b. Use a filter-regulator-lubricator in the air line between the

compressor and the tool when possible.

c. If a lubricator is not available, add 5 to 10 drops of oil in the air

fittingaleasttwiceadayorevery4hoursofuse.

FIG. 2 FIG. 3

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 6 11/14/14 3:06 PM

3. Wear proper eye, hearing and respiratory protection.

 4.Removeallfastenersfromthemagazine.

5. Check for smooth and proper operation of contact trip and

pusher assemblies. Do not use tool if either assembly is not

functioning properly. NEVER use a tool that has the contact trip

restrained in the up position.

 6.Check air supply. Ensure that air pressure does not exceed

recommended operating limits, refer to Tool Specifications.

7. Connect air hose.

8. Check for audible leaks around valves and gaskets. Never use a

tool that leaks or has damaged parts.

WARNING: To reduce the risk of personal injury, disconnect tool

from air supply before performing maintenance, clearing a jammed

fastener, leaving work area, moving tool to another location or

handing the tool to another person.



WARNING: Always wear proper eye [ANSI Z87.1 (CAN/CSA

Z94.3)]andhearingprotection[ANSIS12.6(S3.19)]whenoperating

this tool.

WARNING: Keep fingers AWAY from trigger when not driving

fasteners to avoid accidental firing. NEVER carry tool with finger on

trigger. In contact mode tool will fire a fastener if safety is bumped

while trigger is depressed.

Sequential Trip: Sequential trip requires the operator to hold the

contact tip against the work surface before pulling the trigger. This

makes accurate fastener placement easier. The sequential trip allows

exact fastener placement without the possibility of driving a second

fastener on recoil, as described under Contact Trip. The sequential

trip tool has a positive safety advantage because it will not accidentally

drive a second fastener if the tool is contacted against the work or

anything else while the operator is holding the trigger pulled.

Contract Trip: The common operating procedure on contact trip

tools is for the operator to contact the work surface to actuate

the trip mechanism while keeping the trigger pulled, thus driving

a fastener each time the work is contacted. This will allow rapid

fastener placement on many jobs, such as sheathing, decking

and pallet assembly. All pneumatic tools are subject to recoil when

driving fasteners. The tool may bounce, releasing the trip, and if

unintentionally allowed to recontact the work surface with the trigger

still actuated (finger still holding the trigger pulled) an unwanted

second fastener will be driven.

TO CHANGE OPERATING MODES (FIG. 1, 4–6)

WARNING: Disconnect air line from tool and remove fasteners

from magazine before making adjustments or personal injury may

result.

WARNING: Be aware that once the locking pin is removed, the

trigger is converted to a selectable trigger, enabling either sequential

trip or contract trip operating modes.

WARNING: Always know the tool operating mode before

connecting to an air supply and/or using the tool.

The tool is initially locked in the sequential FIG. 4

trip operating mode. In order to enable the

mode selection feature the mode locking

pin (H) must be removed.

NOTE: The mode locking pin is for

shipping purposes only. Discard pin after

removing.

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 7 11/14/14 3:06 PM

SEQUENTIAL TRIP-

1. Remove mode locking pin (H), if installed.

2. Push and hold in pivot pin (I) while rotating the J

FIG. 5

selector (J) 180° clockwise to the sequential trip

position .

3. Ensure the selector is fully seated in the new

position.

To operate the nailer in sequential trip mode:

1. Depress the contact trip firmly against the work surface.

2. Depress the trigger.

WARNING: A nail will fire each time the trigger is depressed as

long as the contact trip remains depressed.

CONTACT TRIP -

1. Remove mode locking pin, if installed.

2. Push and hold in pivot pin (I) while rotating the

FIG. 6

selector (J) 180° counterclockwise to the

contact trip position .

3. Ensure the selector is fully seated in the new

position.

To operate the nailer in contact trip mode:

1. Depress the trigger.

2. Push the contact trip against the work surface. As long as the

trigger is depressed, the tool will fire a nail every time the contact

trip is depressed. This allows the user to drive multiple nails in

sequence.

WARNING: Do not keep trigger depressed when tool is not in use.



WARNING: Keep tool pointed in a safe direction when loading

nails.

WARNING: Never load nails with the contact trip or trigger

activated.

1. Hold nailer with magazine (F) tilted downward and insert

appropriate collated nail sticks into magazine. See Tool

Specifications to determine appropriate nail sizes and angles.

2. Pull the nail pusher (E) back and carefully allow the pusher to slide

forward until it makes contact with the nails.

FIG. 7



WARNING: Disconnect air line from FIG. 8

tool and remove fasteners from

magazine before making adjustments or

personal injury may result.

English

9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 8 11/14/14 3:06 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere DeWalt Nagelpistole Handbücher

DeWalt

DeWalt DCK264P2T-GB Bedienungsanleitung

DeWalt

DeWalt D51321 Bedienungsanleitung

DeWalt

DeWalt DWFP12231 Bedienungsanleitung

DeWalt

DeWalt N16 series Bedienungsanleitung

DeWalt

DeWalt DC616 Bedienungsanleitung

DeWalt

DeWalt DCN891 Bedienungsanleitung

DeWalt

DeWalt D51822 Bedienungsanleitung

DeWalt

DeWalt DCN692B Bedienungsanleitung

DeWalt

DeWalt DCN890 Bedienungsanleitung

DeWalt

DeWalt D51823 Bedienungsanleitung

DeWalt

DeWalt D51256 Bedienungsanleitung

DeWalt

DeWalt DC613-XE Bedienungsanleitung

DeWalt

DeWalt D51823 Bedienungsanleitung

DeWalt

DeWalt DC616 Bedienungsanleitung

DeWalt

DeWalt DPF1550-XJ Bedienungsanleitung

DeWalt

DeWalt DCN890 Bedienungsanleitung

DeWalt

DeWalt DW46RN Bedienungsanleitung

DeWalt

DeWalt DC608K Bedienungsanleitung

DeWalt

DeWalt D51823 Bedienungsanleitung

DeWalt

DeWalt DPN1850PP-XJ Bedienungsanleitung

DeWalt

DeWalt DCN692 Bedienungsanleitung

DeWalt

DeWalt DCN890 Bedienungsanleitung

DeWalt

DeWalt DPN10033-XJ Bedienungsanleitung

DeWalt

DeWalt D51845 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung