DeWalt DWFP71917 Bedienungsanleitung

DWFP71917

16 Gauge Finish Nailer

Cloueuse de finition de calibre 16

Clavadora de acabado de calibre 16

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT • www.dewalt.com

BEFORE OPERATING THIS TOOL, CAREFULLY READ AND

UNDERSTAND ALL INSTRUCTIONS IN THE IMPORTANT

SAFETY INSTRUCTIONS SECTION.

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please

read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which,

if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

WALT

TOOL, CALL US TOLL FREE AT: 1-800-4-D

WALT (1-800-433-9258)

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Important Safety Instructions

WARNING: Do not operate this unit until you read this instruction manual for

safety, operation and maintenance instructions.

WARNING: This product contains chemicals known to the State of California to

cause cancer, and birth defects or other reproductive harm. Wash hands after

handling.

WARNING: Some dust contains chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm such as asbestos and lead in lead based

paint.

• Actuating tool may result in flying FIG. A

FIG. B

FIG. C

FIG. D

debris, collation material, or dust

which could harm operator’s eyes. The

operator and all those persons in the general area

should wear safety glasses with permanently

attached side shields. Approved safety glasses are

imprinted with the characters “Z87.1”. It is the

employer’s responsibility to enforce the use of eye

protection equipment by the tool operator and other

people in the work area. (Fig. A)

• Always wear appropriate personal

hearing and other protection during

use. Under some conditions and duration of use,

noise from this product may contribute to hearing

loss. (Fig. A)

• Use only clean, dry, regulated air.

Condensation from an air compressor can rust and

damage the internal workings of the tool. (Fig. B)

• Regulate air pressure. Use air

pressure compatible with ratings on

the nameplate of the tool. (Not to exceed

120 psi, 8.3 bar) Do not connect the tool to a

compressor rated at over 200 psi. The tool operating

pressure must never exceed 200 psi even in the

event of regulator failure. (Fig. C)

• Only use air hose that is rated for a

maximum working pressure of at least

150 PSI (10.3 BAR) or 150% of the

maximum system pressure, which ever is greater. (Fig. D)

English

• Do not use bottled gases to power this FIG. E

FIG. F

FIG. G

tool. Bottled compressed gases such as oxygen,

carbon dioxide, nitrogen, hydrogen, propane,

acetylene or air are not for use with pneumatic tools.

Never use combustible gases or any other reactive gas

as a power source for this tool. Danger of explosion

and/or serious personal injury may result. (Fig. E)

• Use couplings that relieve all pressure

from the tool when it is disconnected

from the power supply. Use hose connectors

that shut off air supply from compressor when the tool

is disconnected. (Fig. F)

• Disconnect tool from air supply when

not in use. Always disconnect tool

from air supply and remove fasteners

from magazine before leaving the area

or passing the tool to another operator.

Do not carry tool to another work area

in which changing location involves

the use of scaffoldings, stairs, ladders,

and the like, with air supply connected.

Do not make adjustments, remove

magazine, perform maintenance

or clear jammed fasteners while

connected to the air supply. If the contact

trip is adjusted when the tool is connected to the air supply and nails are loaded,

accidental discharge may occur. (Fig. G)

• Connect tool to air supply before loading fasteners, to

prevent a fastener from being fired during connection. The

tool driving mechanism may cycle when tool is connected to the air supply. Do

not load fasteners with trigger or contact trip depressed, to prevent unintentional

firing of a fastener.

• Do not remove, tamper with, or FIG. H

FIG. I

FIG. J

otherwise cause the tool, trigger, or

contact trip to become inoperable. Do

not tape or tie trigger or contact trip in the ON

position. Do not remove spring from contact trip.

Make daily inspections for free movement of trigger

and contact trip. Uncontrolled discharge could

result.

• Inspect tool before use. Do not

operate a tool if any portion of

the tool, trigger, or contact trip is

inoperable, disconnected, altered,

or not working properly. Leaking air,

damaged parts or missing parts should be repaired

or replaced before use. (Fig. H)

• Do not alter or modify the tool in any

way. (Fig. I)

• Always assume that the tool contains

fasteners.

• Do not point the tool at co-workers or

yourself at any time. No horseplay! Work

safe! Respect the tool as a working implement. (Fig.

• Keep bystanders, children, and

visitors away while operating a

power tool. Distractions can cause you to lose

control. When tool is not in use, it should be locked in a safe place, out of the reach

of children.

• Remove finger from trigger when not driving fasteners.

Never carry tool with finger on trigger. Accidental discharge could

result. Using the trigger lock-off will prevent accidental discharge.

English

• Do not overreach. Maintain proper footing and balance at all times. Loss of

balance may cause cause personal injury. (Fig. K)

• Make sure hose is free of obstructions or snags. Entangled or

snarled hoses can cause loss of balance or footing.

• Use the tool only for its intended use.

Do not discharge fasteners into open

air, concrete, stone, extremely hard

woods, knots or any material too

hard for the fastener to penetrate. Do

not use the body of the tool or top

cap as a hammer. Discharged fasteners may

follow unexpected path and cause injury. (Fig. L)

• Always keep fingers clear of contact

trip to prevent injury from inadvertent

release of nails. (Fig. M)

• Refer to the Maintenance and Repairs

sections for detailed information on

the proper maintenance of the tool

• Always operate the tool in a clean,

lighted area. Be sure the work surface is clear

of any debris and be careful not to lose footing

when working in elevated environments such as

rooftops.

• Do not drive fasteners near edge of

material. The workpiece may split causing the

fastener to ricochet, injuring you or a co-worker.

Be aware that the nail may follow the grain of the

wood (shiner), causing it to protrude unexpectedly

from the side of the work material. Drive the nail

perpendicular to the grain to reduce risk of injury.

(Fig. N)

• Do not drive nails onto the heads of

other fasteners or with the tool at too

steep an angle. Personal injury from strong

recoil, jammed fasteners, or ricocheted nails may

result. (Fig. O)

• Be aware of material thickness when

using the nailer. A protruding nail may cause

injury.

• Be aware that when the tool is being

utilized at pressures on the high end

of its operating range, nails can be

driven completely through thin or

very soft work material. Make sure the

pressure in the compressor is set so that nails are

set into the material and not pushed completely

through. (Fig. P)

FIG. K

FIG. L

FIG. M

FPO

FIG. P

FIG. N

FIG. O

English

• Keep hands and body parts clear of FIG. Q

FIG. R

FIG. S

immediate work area. Hold workpiece with

clamps when necessary to keep hands and body

out of potential harm. Be sure the workpiece is

properly secured before pressing the nailer against

the material. The contact trip may cause the work

material to shift unexpectedly. (Fig. Q)

• Do not use tool in the presence of

flammable dust, gases or fumes. The

tool may produce a spark that could ignite gases

causing a fire. Driving a nail into another nail may

also cause a spark. (Fig. R)

• Keep face and body parts away from

back of the tool cap when working in

restricted areas. Sudden recoil can result in

impact to the body, especially when nailing into

hard or dense material. (Fig. S)

• Grip tool firmly to maintain control

while allowing tool to recoil away

from work surface as fastener is

driven. In “Contact Actuation Mode” if contact

trip is allowed to recontact work surface before

trigger is released an unwanted fastener will be fired.

• Choice of triggering method is

important. Check the manual for triggering

options.

BUMP/CONTACT ACTION TRIGGER

• When using the contact action

FIG. T

trigger, be careful of unintentional

double fires resulting from tool

recoil. Unwanted fasteners may be driven if the

contact trip is allowed to accidentally re-contact

the work surface. (Fig. T)

TO AVOID DOUBLE FIRES:

• Do not engage the tool against the work surface with a strong force.

• Allow the tool to recoil fully after each actuation.

• Use sequential action trigger.

• When “contact” actuating the nailer, always keep tool in

control. Inaccurate placement of tool can result in misdirected discharge of

a fastener.

SEQUENTIAL ACTION TRIGGER

• When using the sequential action FIG. U

trigger, do not actuate the tool

unless the tool is placed firmly

against the workpiece.

• DEPTH ADJUSTMENT: To reduce

riskofseriousinjuryfromaccidental

actuation when attempting to

adjust depth, ALWAYS;

• Disconnect air supply

• Avoid contact with trigger during

adjustments

• Do not drive nails blindly into walls, floors or other work

areas. Fasteners driven into live electrical wires, plumbing, or other types of

obstructions can result in injury. (Fig. U)

• Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use tool while

English

tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious

personal injury.

WARNING: Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday

eyeglasses are NOT safety glasses. Also use face or dust

mask if operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA/Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Tool Speciﬁcations

MODEL DWFP71917

DESCRIPTION 16 Gauge Finish Nailer

ENGINE TYPE Oil-Free

OPERATION PRESSURE

RANGE 70 – 120 psig (4.9 – 8.43 kg/cm2)

MAXIMUM OPERATION

PRESSURE 120 psi (8.43 kg/cm2)

AIR CONSUMPTION AT A

RATE OF 60 FASTENERS

PER MINUTE *

2.0 cfm (56.6 lt/min @

80 psi (5.6 kg/cm2)

FASTENER GAUGE 16 Gauge

FASTENER RANGE 1–1/4" to 2–1/2" (32 mm – 64 mm)

MAGAZINE CAPACITY up to 100 Nails

LENGTH 12-1/2" (316.6 mm)

WIDTH 3-1/3" (84.1 mm)

HEIGHT 11-5/16" (288.5 mm)

WEIGHT 4.4 lbs (2.0 kg)

* The DWFP71917 requires 2.0 cubic feet per minute or cfm (56.6 liters per minute or

lt/min) of free air at 80 psi (5.6 kg/cm2) to operate at a rate of 60 fasteners per minute.

To determine the appropriately sized air compressor, take the actual rate at which the

tool will be run and compare the required cfm (lt/min) to the compressors free air

delivery (cfm/ lt/min) at 80 psi (5.6 kg/cm2).

English

For example, if your fastener usage averages 30 fasteners per minute, you need 50%

of the tools cfm required to operate the tool at the rate of 60 fasteners per minute. In

this case, be sure that your air compressor can deliver a minimum of 1.0 cfm. (28.3 lt/

min) at 80 psi (5.6 kg/cm2) for optimum performance.

COMPONENTS (FIG. 1)

A. Trigger

B. Trigger mode selector

C. Jam clearing latch

D. Contact trip

E. No-mar pad

F. Magazine

G. Pusher

H. Air inlet

I. Rear exhaust

J. Adjustable belt hook

K. Depth adjustment wheel

L. Pencil sharpener

FIG. 1

OPERATION

Preparing the Tool

WARNING: Read the section titled Important Safety Instructions

at the beginning of this manual. Always wear eye and ear protection when operating

this tool. Keep the nailer pointed away from yourself and others. For safe operation,

complete the following procedures and checks before each use of the nailer.

CAUTION: NEVER spray or in any other way apply lubricants or cleaning

solvents inside the tool. This can seriously affect the life and performance of the tool.

NOTE: These nailers are designed to be used without oil.

1. Before you use the nailer, be sure that the compressor tanks have been properly

drained.

2. Wear proper eye, hearing and respiratory protection.

3. Remove all fasteners from the magazine.

4. Check for smooth and proper operation of contact trip and pusher assemblies. Do

not use tool if either assembly is not functioning properly. NEVER use a tool

that has the contact trip restrained in the up position.

5. Check air supply. Ensure that air pressure does not exceed recommended

operating limits, refer to Tool Specifications.

6. Connect air hose.

7. Check for audible leaks around valves and gaskets. Never use a tool that leaks or

has damaged parts.

WARNING: To reduce the risk of personal injury, disconnect tool from air

supply before performing maintenance, clearing a jammed fastener, leaving work area,

moving tool to another location or handing the tool to another person.

Mode Selection

WARNING: Always wear proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and

hearing protection [ANSI S12.6 (S3.19)] when operating this tool.

English

WARNING: Keep fingers AWAY from trigger when not driving fasteners to avoid

accidental firing. NEVER carry tool with finger on trigger. In contact mode tool will

fire a fastener if safety is bumped while trigger is depressed.

The DWFP71917 features a selectable trigger system that allows the user to choose

between the following modes of operation

Sequential Trip

The Sequential Trip requires the operator to hold the tool against the work before

pulling the trigger. This makes accurate fastener placement easier. The Sequential Trip

allows exact fastener location without the possibility if driving a second fastener on

recoil as described under Contact Trip. The Sequential Trip Tool has a positive

advantage because it will not accidentally drive a fastener if the tool is contacted

against the work surface - or anything else - while the operator is holding the trigger

pulled.

Contact Trip

The common operation procedure on “Contact Trip” tools is for the operator to contact

the work surface to actuate the trip mechanism while keeping the trigger pulled, thus

driving a fastener each time the work surface is contacted. This will allow rapid fastener

placement on many jobs. All pneumatic tools are subject to recoil when driving

fasteners. The tool may bounce, releasing the trip, and if unintentionally allowed to

re-contact the work surface with the trigger still actuated (finger still holding the trigger

pulled) an unwanted second fastener will be driven.

TO CHANGE OPERATING MODES (FIG. 1–3)

WARNING: Disconnect air line from tool and remove fasteners from magazine

before making adjustments or personal injury may result.

SEQUENTIAL TRIP ACTION

Use sequential action for intermittent nailing where very careful and accurate placement

is desired.

To operate the nailer in sequential action mode:

1. Rotate the trigger mode selector FIG. 2 (B)

clockwise to the sequential action

position , as shown in Figure 2.

2. Fully depress nosepiece against the work

surface.

3. Pull trigger.

4. Release trigger.

5. Lift nosepiece off work surface.

6. Repeat steps 2 through 4 for next

application.

WARNING: The contact trip needs to be depressed followed by a trigger pull for

each fastener followed by a release of both the contact trip and trigger after each

fastener.

CONTACT TRIP ACTION

Bump/contact action is intended for rapid nailing on flat, stationary surfaces.

When using bump action, two methods are available: place actuation and

bump actuation.

Rotate the trigger mode selector (B) FIG. 3

counterclockwise to the contact action position

, as shown in Figure 3.

To operate the tool using the

PLACE ACTUATION method:

WARNING: A fastener will fire each time

the trigger is depressed as long as the contact

trip remains depressed.

1. Depress the contact trip against the work

surface.

English

2. Depress the trigger.

To operate the tool using the BUMP ACTUATION method:

1. Depress the trigger.

2. Push the contact trip against the work surface. As long as the trigger is depressed,

the tool will fire a fastener every time the contact trip is depressed. This allows the

user to drive multiple fasteners in sequence.

WARNING: Do not keep trigger depressed when tool is not in use. Keep the

contact trip lock-off engaged in the locked position when the tool is not in use.

Tool Operation Check (Fig.1)

WARNING: If the tool is dropped or you suspect tool damage perform tool

operation check.

WARNING: Remove all fasteners from tool before performing tool operation

check.

SEQUENTIAL TRIP ACTION

A. Press the contact trip against the work surface, without touching the trigger.

THE TOOL MUST NOT CYCLE.

B. Hold the tool off the work surface and pull the trigger.

THE TOOL MUST NOT CYCLE.

C. Pull the trigger and press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

D. With finger off the trigger, press the contact trip against the work surface. Pull the

trigger.

THE TOOL MUST CYCLE.

CONTACT TRIP ACTION

A. With finger off the trigger, press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

B. Hold the tool off the work surface, and pull the trigger.

THE TOOL MUST NOT CYCLE.

C. With the tool off the work surface, pull the trigger. Press the contact trip against

the work surface.

THE TOOL MUST CYCLE.

D. Without touching the trigger, press the contact trip against the work surface, then

pull the trigger.

THE TOOL MUST CYCLE.

Loading the Tool (Fig. 4)

WARNING: Keep tool pointed in a safe direction when loading nails.

WARNING: Never load nails with the contact trip or trigger activated.

1. Load nails through the slot in the rear of the magazine and past retaining clip.

2. Pull pusher back behind nail stick and release.

3. Ensure magazine pusher is behind the last nail stick.

FIG. 4

Depth Setting (Fig. 1)

WARNING: Disconnect air line from tool and remove fasteners from magazine

before making adjustments or personal injury may result.

The fastener depth control adjustment feature provides control of the nail drive

depth from flush with or just above the work surface to shallow or deep countersink.

Rotate depth control adjustment wheel (K) to give the desired depth of drive.

English

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere DeWalt Nagelpistole Handbücher

DeWalt

DeWalt DPN1850PP-XJ Bedienungsanleitung

DeWalt

DeWalt DCN690 Bedienungsanleitung

DeWalt

DeWalt DCN692 Bedienungsanleitung

DeWalt

DeWalt D51236 Bedienungsanleitung

DeWalt

DeWalt DCN692M1 Bedienungsanleitung

DeWalt

DeWalt D51257K Bedienungsanleitung

DeWalt

DeWalt DWFP72155 Bedienungsanleitung

DeWalt

DeWalt DCN690 Bedienungsanleitung

DeWalt

DeWalt DCN890 Bedienungsanleitung

DeWalt

DeWalt DC608K Bedienungsanleitung

DeWalt

DeWalt D51238 Bedienungsanleitung

DeWalt

DeWalt D51822-XE Bedienungsanleitung

DeWalt

DeWalt D51275 Bedienungsanleitung

DeWalt

DeWalt DWFP12569 Bedienungsanleitung

DeWalt

DeWalt D51321 Bedienungsanleitung

DeWalt

DeWalt D51238 Bedienungsanleitung

DeWalt

DeWalt DCN680 Bedienungsanleitung

DeWalt

DeWalt DCN692 Bedienungsanleitung

DeWalt

DeWalt DCN662 Bedienungsanleitung

DeWalt

DeWalt DCN890P2 Handbuch

DeWalt

DeWalt D51276-XE Bedienungsanleitung

DeWalt

DeWalt DCN891 Bedienungsanleitung

DeWalt

DeWalt D51180 Bedienungsanleitung

DeWalt

DeWalt DCN45RN Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung