Dexter Laundry T-30X2 Montageanleitung

8514-211-001 REV D PAGE 1

INDUSTRIALDRYER OriginalInstructions

MODEL T-30X2 ON-PREMISE For GB & IE

B-SERIES CONTROL, ELECTRIC-HEATED

OPERATOR’S MANUAL

INSTALLATION & OPERATION INSTRUCTIONS

The dryer will operate correctly in ambient temperatures of 5°C to 45°C, in relative humidity

up to 50% at 40°C and above 50% when below 40°C, and at altitudes up to 1000m above

sea level, must be transported and stored from -40°C to 140°C, and has been packaged to

prevent damage from humidity, vibration, and shock. Take measures to avoid harmful

effects of occasional condensation.

Post the following “For Your Safety” cautions in a prominent location:

FOR YOUR SAFETY

Do not store or use petrol or other flammable vapours and liquids or dry cleaning

solvents in the vicinity of this or any other appliance.

FOR YOUR SAFETY

THIS MACHINE IS FOR DRYING ONLY FABRICS WASHED IN WATER. To avoid

possibility of fire, including spontaneous combustion, do not dry oiled floor mops, items

containing foam rubber or similarly textured rubberlike materials or any material on

which you have used a cleaning solvent or which contains flammable liquids or solids

(such as petrol, kerosene, waxes, etc.) Fabric softeners, or similar products, should be

used per the fabric softener instructions. Remove all objects from pockets such as

lighters and matches.

WARNING – Risk of Fire

Clothes dryer installation must be performed by a qualified installer.

Install the clothes dryer according to the manufacturer’s instructions and local codes.

Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)

duct is installed, use duct that has been investigated and found acceptable for use with

clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap

lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

To reduce the risk of severe injury or death, follow all installation instructions.

This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised.

It is important that you read this Manual and retain it for future reference. For service

or replacement parts, contact the distributor in your area or the manufacturer:

Dexter Laundry, Inc.

2211 West Grimes Avenue

Fairfield, Iowa 52556, USA

-2-

TABLE OF CONTENTS

Page No.

Dryer Dimensions (Figure 1)............................................................................. 4

Uncrating ..................…...................................................................................5

Dryer Installation (Figure 2)..............................................................................6

Dryer Exhaust System (Figure 3).......................................................................10

Dryer Shutdown...............................................................................................10

Touch Pad Layout (Figure 4).............................................................................11

Dryer Default Settings...................................................................................... 12

Dryer Default Codes......................................................................................... 12

Touch Pad Description......................................................................................13

Operating Instructions......................................................................................15

Programming Instructions.................................................................................17

Servicing Dryer................................................................................................ 24

Preventive Maintenance....................................................................................24

WARNINGS ABOUT USE AND OPERATION

Caution! There are sharp ed

es on various sheet metal parts internal

to the enclosure. Use safety consciousness when placing or moving

your hands while working in the interior of this equipment.

Meaning: Do Not Enter This

Equipment (or Space).

Meaning: Do Not Step, Stand, or Sit

on This Equipment.

Meaning: Do Not Operate with

Guards or Covers Removed.

Meaning: High Voltage. Disconnect

power before servicing.

Meanin

: Lock Out and Ta

Out

before servicing.

Meaning: Burn Hazard. Do Not Touch

Heater Housing or Heating Elements.

Allow these parts to cool before servicing.

Meaning: Do Not Dry Items

Containing Explosive Material.

Meaning: Do Not Dry Items

Containing Flammable Material.

Meaning: Read Operators

Manual.

Meaning: Center of Gravity.

Meaning: Left Point for Forklift

or Hand Pallet Truck or Jack.

Meaning: Right Point for Forklift or

Hand Pallet Truck or Jack.

It is ABSOLUTELY ESSENTIAL that the dryer be connected to a known earth

connection. This is not only for personal safety, but is necessary for proper operation.

DO NOT MODIFY THIS APPLIANCE. KEEP SHIELDS, GUARDS AND COVERS IN

PLACE. These safety devices are provided to protect everyone from injury.

-3-

WARNINGS ABOUT USE AND OPERATION continued

THIS DRYER IS EQUIPPED WITH A MANUALLY RESETTABLE OVER-

TEMPERATURE THERMOSTAT located on the top of the exhaust duct beside the

motor. Should the dryer cease to heat, reset the thermostat by rotating the lever

bracket clockwise. Should the thermostat continue to trip, the dryer must be inspected

by a qualified service person.

CHECK THE THERMOSTAT WHEN INSTALLING DRYER to assure it is not tripped.

Impacts, such as rough handling in shipment, may trip the thermostat.

WARNING: Do not stop dryer before end of cycle time unless all items are quickly

removed and spread out to dissipate heat.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE while in

operation.

THIS APPLIANCE SHALL NOT BE USED TO DRY OFF CLOTHES CONTAINING

SOLVENTS OR DRY-CLEANING FLUIDS.

Misuse of Dryer

Do not use this Equipment for any purpose not described in this Manual.

Do not operate this equipment without all guards and covers in place.

Do not operate this dryer from any power source not matching the

operational requirements on the back of the dryer.

Do not place your body inside the dryer cylinder or allow others to do so.

Death or serious injury can result from this!

Other Examples May Be Applicable

Caution – Replace Fuses With Same Type and Rating

Fuse No. Voltage Amperage SC I/R Type Size

F1 in

front

control

250V 600mA 35A@250VAC T 5.00 x 20.00 mm

-4-

FIGURE 1 Dryer Dimensions - inches (mm)

MAX

MIN

-5-

INSTALLATION AND OPERATING INSTRUCTIONS

Note: A forklift, or a hand pallet truck or jack, must lift the dryer and only from

the front or rear of the dryer with the dryer bolted to the pallet and supported

the full length of the dryer.

UNCRATING AND PLACING DRYER

Tools Required: 3/4" (19 mm) hex socket & ratchet driver, wood block 4" (100 mm) or

5" (125 mm) thick, a knife and a groove joint pliers, which will open to 1 3/8" (35 mm).

1. Remove and discard packaging.

2. The crate base is attached to the dryer by (4) cap screws driven upward from

below the crate base. Remove crate base from the dryer, by tipping the dryer

sidewise and place the block under the crate base rail in center of the dryer.

Using a ratchet and 3/4" (19 mm) hex socket, remove the (2) crating bolts from

the side, which is raised, and save for future moving of the dryer. Remove the

block from under the crate base. Repeat for the other side.

3. With a walking motion, move the dryer completely off the crate base. Save the

crate base for future moving of the dryer.

4. Slide the unit into position where it will be installed. Adjust the leveling legs,

using the groove joint pliers, to level and align the dryer with adjacent units.

Note: If the dryer is ever moved again, the dryer should be re-mounted on its pallet

and its crating bolts re-inserted and tightened, in the reverse order as above.

Dryer Model Mass

DN30X2E_-79 340 kg

DRYER INSTALLATION

1. CODE CONFORMITY: All industrial dryer installations must conform to the local and

national codes for the location of installation. Prior to installation, ensure that the local

distribution conditions (identification of the type) and the adjustment of the appliance

are compatible.

The appliance must not be installed behind a lockable door, a sliding door or a door

with a hinge on the opposite side to that of the tumble dryer, in such a way that a full

opening of the tumble dryer door is restricted.

2. INSTALLATION CLEARANCES: This unit may be installed at the following alcove

clearance.

I. Left Side 0 in.

II. Right Side 0 in.

-6-

III.Back 18 in. (457 mm) (Certified for 6 in. (150 mm) clearance; however,

18 in. (457 mm) clearance is necessary behind the motors to allow

servicing and maintenance.)

IV. Front 48 in. (1220 mm) to allow use of dryer.

V. Top Refer to figure labeled “Vertical Clearance Dimensions”.

AB. Certification allows 0 in. clearance at the top 4 in. (100 mm)

back from the front. However, a 1/4 in. (6 mm) clearance should

be allowed in case the dryer needs moving.

C. A 10 in. (250 mm) clearance is required from top at all other

points.

VI. Floor This unit may be installed upon a combustible floor.

Do not obstruct the flow of combustion and ventilation air.

Maintain minimum of 1 in. (25 mm) clearance between duct and combustible material.

Refer to the label attached to the Belt Guard on the rear of the dryer for other

installation information and start-up instructions.

3. MAKE-UP AIR. Adequate make-up air (600CFM/DRUM (17 m3/Min.),

1200CFM/DRYER) (34 m3/Min.) must be supplied to replace air exhausted by dryers on

all types of installations. Provide a minimum of 1.5 sq. ft. (0.14 m2) make-up air

opening to the outside of each dryer. This is a net requirement of effective area.

Screens, grills or louvers, which will restrict the flow of air, must be considered. Consult

the supplier to determine the free area equivalent for the grill being used.

TOP OF DRYER

SIDE OF DRYER

FRONT

DRYER

FIGURE

Vertical Clearance Dimensions

-7-

The source of make-up air should be located sufficiently away from the dryers to allow

an even airflow to the air intakes of all dryers. Multiple openings should be provided.

The operation of this appliance may affect the operation of gas appliances, which take

their air for safe combustion from the same room. Adequate ventilation must be

provided to avoid back flow of gasses from other appliances in the same room. All gas

appliances should be tested with the Dexter dryer in operation and all the windows and

doors closed. If in doubt, consult the appliance manufacturer(s).

4. ELECTRICAL REQUIREMENTS:

The electrical installation must be performed by a qualified electrical technician.

The electrical power requirements necessary to operate the unit satisfactorily are listed

on the serial plate located on the back panel of each dryer. The electrical connection

should be made at the terminal blocks in the two control boxes on the rear of the unit

using conductors rated at 75°C (167°F) and a wire size adequate to handle the

amperage and voltage listed on the serial plate (see table below for recommended

minimum sizes). It is absolutely necessary that the dryer be connected to a known

earth (No. 8 AWG copper conductor recommended). Knockouts are provided for the

connection of 1-inch (25 mm) conduit for the power supply conductors and 3/8-inch

(10 mm) conduit for the external earthing conductor. It is absolutely necessary that the

dryer be connected to a good earth connection. The earth connection resistance should

be checked prior to operation at the end. Introduction of supply wiring must not

increase the Ingress Protection (IP) rating.

HEATING

ELEMENT SIZE

(kW)

SUPPLY

VOLTAGE

(PHASE / V.)

MINIMUM DUAL ELEMENT TIME

DELAY FUSE SIZE AT FUSED

DISCONNECT (A.)

MINIMUM WIRE SIZE FROM FUSED

DISCONNECT TO DRYER TERMINAL

BLOCK (75OC COPPER WIRE)

24 3

400 50 # 6

(

13.3 mm^2

)

The installation must meet the electrical requirements of the country, state and

locality of the installation. Individual circuit breakers for each dryer are required. The

installer must provide a disconnect switch which will interrupt all lines. It may be a

local or national requirement to provide an electrical interruption switch visible and

accessible from the room in which the dryer is installed. The wiring diagram is located

in the control box on the back of the dryer.

For destination countries where CE requirements must be met, individual 400V supply

disconnecting devices for each dryer are required and must be one of the following

types:

a. switch-disconnector with fuses per IEC 60947-3 utilization category AC-23B;

b. disconnector with fuses per IEC 60947-3 having an auxiliary contact that in all cases

causes switching devices to break the load circuit before the opening of the main

contacts of the disconnector;

c. a circuit-breaker suitable for isolation per IEC 60947-2;

d. any other switching device in accordance with an IEC product standard for that

device and which meets the isolation requirements of IEC 60947-1 as well as a

-8-

utilization category defined in the product standard as appropriate for on-load switching

of motors or other inductive loads;

The supply disconnecting devices must

a. provide a means allowing the supply disconnecting devices to be locked in the OFF

position;

b. be mounted 0.7m to 1.7m above the floor, within 2 m from the dryer, and within 8 m

from the operator position;

c. have a red actuator to indicate that it serves a dual Emergency Stop function;

d. be rated for branch circuit operation;

e. be approved for use in the country where installed;

CONTROL TRANSFORMER CONNECTIONS Adjustment for different voltages of supply mains.

IMPORTANT: TRANSIENT VOLTAGE SURGE SUPPRESSORS

Like most electrical equipment your new machine can be damaged or have its life

shortened by voltage surges due to lightning strikes which are not covered by factory

warranty. Local power distribution problems also can be detrimental to the life of

electrical components. We recommend the installation of transient voltage surge

suppressors for your new equipment. These devices may be placed at the power

supply panel for the complete installation and don’t require an individual device for each

machine.

These surge protectors help to protect equipment from large spikes and also from small

ongoing spikes in the power that occur on a day to day basis. These smaller surges can

shorten overall life of electrical components of all types and cause their failure at a later

date. Although they can’t protect against all events, these protective devices have a

good reputation for significantly lengthening the useful life of electronic components.

Electronic components are helped to have a longer useful life when they are supplied

with the clean stable electrical power they like.

6. EXHAUST INSTALLATION. (Refer to Figure 3) Exhausting of the dryer(s) should

be planned and constructed so that no air restrictions occur. Any restriction due to pipe

size or type of installation can cause slow drying time, excessive heat, and lint in the

room.

-9-

From an operational standpoint, incorrect or inadequate exhausting can cause a

cycling of the high limit thermostat, which shuts off the heating elements and results in

inefficient drying.

The exhaust duct connection near the top of the dryer will accept an 8 in. (200 mm)

round duct. Individual exhausting of the dryers is recommended. A pipe of the proper

diameter should be attached to the dryer adapter collar and extended out through an

outside wall to exhaust all heat, moisture, and lint outside. This pipe must be very

smooth on the inside, as rough surfaces tend to collect lint, which will eventually clog

the duct and prevent the dryer from exhausting properly. All elbows must be smooth

on the inside. All joints must be made so the exhaust end of one pipe is inside the next

one downstream. The addition of an exhaust pipe tends to reduce the amount of air

the blower can exhaust. This does not affect the dryer operation if held within practical

limits. For the most efficient operation, it is recommended that no more than 14 ft.

(4.25 m) of straight 8 in. (200 mm) diameter pipe is used with two right angle elbows.

The design of the vent system shall be such that any condensate formed when

operating the dryer from cold shall either be retained and re-evaporated or discharged.

Maintain a minimum of 1” (25mm) clearance between duct and combustible material.

If the exhaust pipe passes through a wall, a metal sleeve of slightly larger diameter

should be set in the wall and the exhaust pipe passed through this sleeve. This practice

is required by some local codes and is recommended in all cases to protect the wall.

This type of installation should have a means provided to prevent rain and high winds

from entering the exhaust when the dryer is not in use. A hood with a hinged damper

can be used for this purpose. Another method would be to point the outlet end of the

pipe downward to prevent entrance of wind and rain. In either case, the outlet should

be kept clear, by at least 24 in. (610 mm), of any objects, which would cause air

restriction.

Never install a protective screen over the exhaust outlet.

When exhausting a dryer straight up through a roof, the overall length of the duct has

the same limits as exhausting through a wall. A rain cap must be placed on top of the

exhaust and must be of such a type as to be free from clogging. The type using a cone

shaped “roof” over the pipe is suitable for this application.

Exhausting the dryer into a chimney or under a building is not permitted. The exhaust

air should not be vented into a wall, a ceiling, or a concealed space of building. In

these cases, there is a danger of lint buildup, which can be highly combustible.

Installation of several dryers, where a main discharge duct is necessary, will need the

following considerations for installation (see Figure 3). Individual ducts from the dryers

into the main discharge duct should be at a 45-degree angle in the direction of

discharge airflow.

NOTE: Never install the individual ducts at a right angle into the main discharge duct.

The individual ducts from the dryers can enter at the sides or bottom of the main

discharge duct. Figure 3 indicates the various round main duct diameters to use with

-10-

the individual dryer ducts. The main duct can be rectangular or round, provided

adequate airflow is maintained. For each individual dryer, the total exhausting (main

discharge duct plus duct outlet from the dryer) should not exceed the equivalent of 14

ft. (4.25 m) and two elbows. The diameter of the main discharge duct, at the last

dryer, must be maintained to exhaust end.

NOTE: A small diameter duct will restrict airflow; a large diameter duct will reduce air

velocity - both contributing to lint build up. An inspection door should be provided for

periodic clean out of the main duct.

NOTE: Exhaust air must not be discharged into a flue which is used for exhausting

fumes from appliances burning gas or other fuels.

NOTE: The A-weighted emission sound pressure level does not exceed 70dB(A). The

operator does not need hearing protection.

NOTE: The dryer does not emit hazardous radiation.

WARNING: To avoid potential risks of spontaneous combustion of a load,

remove the load quickly after the completion of the cycle or in case of failure

of power supply.

DANGER: Do not dry loads which may create an explosive atmosphere in the

dryer.

DRYER SHUTDOWN

To render the dryer inoperative, disconnect electrical supply to the dryer.

Caution - A clothes dryer produces combustible lint and should be

exhausted outdoors. The area around the clothes dryer should be kept

free of lint.

DIAMETER TO INCREASE AS SHOWN

WALL

INSTALL NO

SCREEN OR

COVER

EXHAUST AIR

(SEE INSTRUCTIONS)

DRYER DUCTS

MUST ENTER AT

A 45° ANGLE

INCHES

(MM)

INSPECTION

COVER

FIGURE 3- Dryer Exhausting Using A Main Discharge Duct.

Andere Handbücher für T-30X2

Inhaltsverzeichnis

Andere Dexter Laundry Trockner Handbücher

Dexter Laundry

Dexter Laundry DTCH30 series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20SWD Montageanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Administratorhandbuch

Dexter Laundry

Dexter Laundry DL2X30Q Handbuch

Dexter Laundry

Dexter Laundry DC30X2 Series Bauanleitung

Dexter Laundry

Dexter Laundry C Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DCT30KC Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry DN20X2 Leitfaden

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry DDAD30HC-11 Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Kurzanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry B-Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DRC55 Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry DCBD30KC-64F Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DDAD T-30 2 Series Administratorhandbuch

Dexter Laundry

Dexter Laundry DN0170 XL Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-80 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 SWD Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung