Dexter Laundry T-1450 Installationshandbuch
OPL PROGRAMMING V-SERIES
TWO WAYS TO MODIFY PROGRAMMING OF THE V-SERIES OPL SIX (6)
PREPROGRAMMED FORMULAS
#1 Programming can be accomplished manually using the machine controls or by connecting to
the machine control using a PDA (personal digital assistant). For instructions on using a PDA
with this washer control, please contact your local Dexter distributor.
The keypad layout for the washer control is shown above.
#2 Manual Wash Cycle Programming Instructions
1. Turn on the power to the washer.
2. Turn the Run/Program key to the Program position. Display will show “C O” and the
“ADD BLEACH” will blink and will continue to blink during the programming mode.
3. Press the “DOWN” or “UP” buttons to select which cycle to alter. When the desired
cycle number is displayed, press “START”.
4. The display should now show a “b”. The “b” and the cycle indicator lights indicate
which bath is being selected to alter. Press the “UP” and “DOWN” buttons to select a
bath to change and then press “START”. The indicator lights are shown below.
FINAL
RINSE
PRE
WASH
FLUSH WASH RINSE SPIN
When “RINSE” is selected, “b r1” through “b r4” may be selected. There may be
multiple rinses that are indicated by r1, r2, r3 and r4.
5.Each bath can be programmed with the following options. Use the “DOWN” and “UP” keys to
select the desired setting and the “START” key to move to the next option.
DISPLAY FUNCTION OPTIONS
Ct ** Tumble Time Two-digit amount of time in minutes.
t ** Water Temperature HH for hot, CH for warm, CC for cold
and EE for no water.
L ** Water Level Lo for low, Hl for high.
dF * Type of Fill d for delayed fill, t for timed fill.1
S ** Spin Time Two-digit amount of time in minutes.
IS * Injection Source Single digit code indicating injector signal(s).2
1 A delayed fill will pause the time count until the selected level is reached. A timed fill
will only fill for a predetermined amount of time.
2Codes for injections sources are defined at the end of the programming section. When
the No Water bath is selected, the electronic controller prohibits injection signals. The
programmed injection source value is ignored.
To exit the programming of a bath, press the “STOP” button once and use the “UP” and
“DOWN” keys select another bath. Press the “STOP” button again to select a different cycle to
change. To end programming, turn the key to “RUN” position
Note: The Wash Cycle programming mode will automatically exit and return to
the Idle mode if no buttons are pushed for one minute.
WASHER CYCLE PARAMETER RANGES
The range of each cycle parameter is shown below:
Cycle Time 0 to 15 minutes for Prewash, Wash, Rinse1, 2, 3 and 4
1 to 15 minutes for Final Rinse
For the bathes that can, if the time is set to zero, then the
bath will be eliminated from the cycle.
Water Temperature HH – hot, CH – warm, CC – cold, EE – no water
Water Level HI – high, LO – low
Delay Fill The selections are “d” for delay the bath time until water
level is reached or “t” for decrement bath time during the
fill.
Spin Time 0 to 10 minutes for Prewash, Wash, Rinse, 2, 3 and 4
1 to 10 minutes for Final Spin
Injection Source 0 to 6
Cycle 1 Sheets & Pillowcases (Health Care)
Bath
Bath Cycle
Time
(min.)
Water
Temp.
Water
Level
Delay
Fill
Spin
Time
(min.)
Injection Source
Flush 3 CH HI d
Prewash 2 CH HI d
Wash 7 HH LO d 1 (Detergent)
Rinse 1 7 HH LO d 2 (Bleach)
Rinse 2 2 CH HI d 1
Rinse 3 2 CH HI d
Rinse 4
Final
Rinse
4 CH LO d 4 4 (Sour/Soft)
Cycle 2 Towels / Pads / Diapers (Health Care)
Bath
Bath Cycle
Time
(min.)
Water
Temp.
Water
Level
Delay
Fill
Spin
Time
(min.)
Injection Source
Flush 3 CH HI d
Prewash 2 CH HI d
Wash 7 HH LO d 1 (Detergent)
Rinse 1 1 HH HI d
Rinse 2 7 HH LO d 2 (Bleach)
Rinse 3 2 CH HI d 1
Rinse 4 2 CH HI d
Final
Rinse
4 CH LO d 5 4 (Sour/Soft)
Cycle 3 White Towels (Hotel / Motel)
Bath
Bath Cycle
Time
(min.)
Water
Temp.
Water
Level
Delay
Fill
Spin
Time
(min.)
Injection Source
Flush
Prewash
Wash 7 HH LO d 1 (Detergent)
Rinse 1 1 HH HI d
Rinse 2 7 HH LO d 2 (Bleach)
Rinse 3 2 CH HI d 1
Rinse 4 2 CH HI d
Final
Rinse
4 CH LO d 5 4 (Sour/Soft)
Cycle 4 Guest Laundry (Hotel / Motel or Health Care)
Bath
Bath Cycle
Time
(min.)
Water
Temp.
Water
Level
Delay
Fill
Spin
Time
(min.)
Injection Source
Flush 3 CH HI d
Prewash
Wash 7 HH LO d 5
(Detergent/Bleach)
Rinse 1 2 HH HI d
Rinse 2 2 CH HI d
Rinse 3 2 CH HI d
Rinse 4
Final
Rinse
4 CH LO d 4 4 (Sour/Soft)
Cycle 5 Rags & Mops (Hotel / Motel)
Bath
Bath Cycle
Time
(min.)
Water
Temp.
Water
Level
Delay
Fill
Spin
Time
(min.)
Injection Source
Flush 3 CH HI d
Prewash 2 CH HI d
Wash 2 CH HI d
Rinse 1 7 HH LO d 1 (Detergent)
Rinse 2 2 HH HI d
Rinse 3 7 HH LO d 2 (Bleach)
Rinse 4 2 CH HI d 1
Final
Rinse
2 CH LO d 5
Cycle 6 Colored Cotton Linen (Food & Beverage)
Bath
Bath Cycle
Time
(min.)
Water
Temp.
Water
Level
Delay
Fill
Spin
Time
(min.)
Injection Source
Flush 2 CH HI d
Prewash
Wash 10 HH LO d 1 (Detergent)
Rinse 1 7 HH LO d 2 (Bleach)
Rinse 2 2 CH HI d 1
Rinse 3 2 CH HI d
Rinse 4
Final
Rinse
4 CH LO d 4 6 (Sour/Starch)
RAPID ADVANCE MODE
To enter the Rapid Advance mode, turn the key CCW. The Rapid Advance setting is not marked
next to the key, but turning the CCW until it stops selects this mode. The Rapid Advance mode
can be entered from either the Idle mode or during the cycle. If the cycle has not yet started,
press the “START” button. To rapid advance to the next step in the wash cycle, push both the
“UP” and “START” buttons at the same time. The display will show an “Ad” (advance) in the
display. The washer will advance to the next bath segment. The water will drain before the
advance will occur and the time displayed may not be accurate.
Notes: - The indicator lights will show to which segment the cycle has been advanced.
- The cycle will continue in rapid advance mode even if the key is turned to “RUN” and/or
removed.
- Rapid advance cannot skip the final 1-minute tumble of the cycle, and the door lock may
remain activated for a couple minutes after the cycle has been completed.
-Chemical 120volt signals will be lost after Rapid advance Mode has been activated until
cycle resets.
To exit the Rapid Advance mode, push and hold the STOP button.
INJECTION SOURCE DETAILS
The washer control may be programmed to send output signals for a chemical injection system.
There is a separate terminal block for connection of the external injection signals. For the
injection sources, program codes 0 through 6 are as shown in the table below.
Dexter
Recommended
Connections
Controller
Programmed
Signals
Injection
Terminal Block
Circuits
Detergent 1 A
Bleach 2 B
Starch 3 C
Sour/Softener 4 D
5 A and B
6 C and D
0 None
Inhaltsverzeichnis
Andere Dexter Laundry Waschmaschine Handbücher
Dexter Laundry
Dexter Laundry T-300 VENDED Kurzanleitung
Dexter Laundry
Dexter Laundry OPL Series Kurzanleitung
Dexter Laundry
Dexter Laundry T-300 VENDED Bedienungsanleitung
Dexter Laundry
Dexter Laundry 75LB CAPACITY COMPUTER CONTROL OPL WASHER Bedienungsanleitung
Dexter Laundry
Dexter Laundry WC0300XA-10EC4X Bedienungsanleitung
Dexter Laundry
Dexter Laundry HIGH SPEED 25LB WASHER Montageanleitung
Dexter Laundry
Dexter Laundry WCVD-WN Series Kurzanleitung
Dexter Laundry
Dexter Laundry WCVD Series Administratorhandbuch
Dexter Laundry
Dexter Laundry WC 00XA-12EC X Series Bedienungsanleitung
Dexter Laundry
Dexter Laundry T-900 Bedienungsanleitung
Dexter Laundry
Dexter Laundry O Series Kurzanleitung
Dexter Laundry
Dexter Laundry T350 Bedienungsanleitung
Dexter Laundry
Dexter Laundry WCAD Series Kurzanleitung
Dexter Laundry
Dexter Laundry WCN Series Bedienungsanleitung
Dexter Laundry
Dexter Laundry WCVD-WN Series Betriebsanleitung
Dexter Laundry
Dexter Laundry T-1800 Bedienungsanleitung
Dexter Laundry
Dexter Laundry 80LB CAPACITY COMPUTER CONTROL OPL WASHER... Bedienungsanleitung
Dexter Laundry
Dexter Laundry T450 Express Bedienungsanleitung
Dexter Laundry
Dexter Laundry T-650 Kurzanleitung
Dexter Laundry
Dexter Laundry T-300 VENDED Bedienungsanleitung
