DFI-ITOX G4C600-R Bedienungsanleitung

G4C600-R

G4C600-D

G4C600-DG

Rev. A+

System Board

User’s Manual

I73710346

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98 SE, Windows®ME, Windows®2000, Windows NT®

4.0 and Windows®XP are registered trademarks of Microsoft

Corporation. Intel®and Pentium®4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Important Configuration and Driver Installation Rules

HighPoint RAID IDE Controller (G4C600-R only)

By default, the HighPoint RAID IDE controller is enabled. If you

are not using this function, make sure to set the “RAID Device

Control” field in the Integrated Peripherals submenu of the Award

BIOS to Disabled.

Make sure to follow the rule mentioned above. Doing it other-

wise will slow down the boot up time and affect the perform-

ance of the system.

Driver Installation Rules

Please follow the installation sequence below.

1. Install the “Audio Drivers”.

2. Install the “Intel Chipset Software Installation Utility”.

3. Install the other drivers and utilities.

Make sure to follow this sequence. Doing it otherwise will slow

down the boot up time and affect the performance of the sys-

tem.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications...............................................................................

1.2 Hyper-Threading Technology Functionality Requirements.......

1.3 Package Checklist......................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ........................................................................................

2.2 System Memory........................................................................................................

2.3 CPU.....................................................................................................................................

2.4 Jumper Settings..........................................................................................................

2.5 Rear Panel I/O Ports...........................................................................................

2.6 I/O Connectors........................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility.................................................................................

3.2 Intel LAN BIOS Setting Utility.......................................................................

3.3 Intel ICH5R BIOS Setting Utility..................................................................

3.4 HighPoint BIOS Configuration Utility.......................................................

3.5 Updating the BIOS..................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.............................................................

4.2 Drivers, Utilities and Software Applications.................................

4.3 3D Audio Configuration.................................................................................

4.4 Installation Notes..................................................................................................

100

101

103

106

118

121

Introduction

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...................................

Appendix B - System Error Messages

B.1 POST Beep......................................................................................................................

B.2 Error Messages............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist..............................................................................

122

125

127

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• Intel®875P chipset

- Intel®82875P Memory Controller Hub (MCH)

- Intel®82801ER I/O Controller Hub (ICH5R)

Processor

The system board is equipped with Socket 478 for installing one of

the following supported processors.

• Intel®Pentium®4 Processor with Hyper-Threading Technology

- 800MHz/533MHz system data bus

• Intel®Pentium®4 Northwood processor

- 533MHz/400MHz system data bus

• Intel®Pentium®4 Prescott processor

- 800MHz system data bus

• Intel®Celeron®Northwood processor

- 400MHz system data bus

Note:

Refer to section 1.2 and appendix A for more information on

the Hyper-Threading Technology.

System Memory

• Supports dual channel (128-bit wide) memory interface

- Each channel supports 2 DIMM sockets

• Supports up to 4GB system memory

• Supports Dynamic mode to optimize system performance

• Synchronous operation with processor system bus

- PC2100/PC2700/PC3200 (DDR266/DDR333/DDR400)

with 800MHz FSB CPU (supports PAT mode). DDR333 will

run at 320MHz memory frequency when used with 800MHz

FSB CPU.

Chapter 1 - Introduction

Introduction

Performance Acceleration Technology (PAT)

PAT mode is supported only when the system uses DDR400 with

800MHz FSB CPU. PAT performs data transactions directly from the

CPU to the system memory, bypassing the normal path of

operation. This reduces the MCH timing therefore providing

improved system performance.

Expansion Slots

The system board is equipped with 1 AGP slot and 5 PCI slots.

AGP (Accelerated Graphics Port)

• Supports AGP 3.0 (AGP 4x and 8x) and AGP 2.0 (AGP 1x and

4x) spec.

• Supports 1.5V AGP 8x (2.13GB/sec.) and AGP 4x (1066MB/

sec.) add-in cards.

AGP is an interface designed to support high performance 3D

graphics cards for 3D graphics applications. It handles large

amounts of graphics data with the following features:

• Pipelined memory read and write operations that hide

memory access latency.

• Demultiplexing of address and data on the bus for nearly

100 percent efficiency.

Note:

AGP 2x and 3.3V AGP cards are not supported.

Density Width

Single/Double

184-pin DDR

64 Mbit

SS/DS

64/128MB

X16

SS/DS

32MB/NA

Density 128 Mbit

SS/DS

128/256MB

X16

SS/DS

64MB/NA

256 Mbit

SS/DS

256/512MB

X16

SS/DS

128MB/NA

512 Mbit

SS/DS

512/1024MB

X16

SS/DS

256MB/NA

- Use PC2100/PC2700 (DDR266/DDR333) with 533MHz

FSB CPU

- Use PC2100 (DDR266) with 400MHz FSB CPU

• Supports ECC/non-ECC DIMMs

• Supports unbuffered DIMMs

Introduction

Onboard Audio Features

• 20-bit stereo full-duplex codec with independent variable sam-

pling rate

• High quality differential CD input

• True stereo line level outputs

• S/PDIF-in/out interface

• 6-channel audio output

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to an

analog format. This prevents the quality of the audio signal from

degrading whenever it is converted to analog. S/PDIF is usually

found on digital audio equipment such as a DAT machine or audio

processing device.The S/PDIF connector on the system board sends

surround sound and 3D audio signal outputs to amplifiers and

speakers and to digital recording devices like CD recorders.

6-channel Audio

The 6-channel audio output function is supported by using the 4-

channel connector, the audio jacks at the rear panel and configuring

the audio driver. Please refer to chapters 2 and 4

Onboard LAN Features

• G4C600-R and G4C600-D only

- Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compat-

ible PHY

- 32-bit PCI master interface

- Integrated power management functions

- Full duplex support at both 10 and 100 Mbps

- Supports IEEE 802.3u auto-negotiation

- Supports wire for management

• G4C600-DG only

- 82547EI Gigabit LAN CSA interface

- Integrated power management functions

- Full duplex support at both 10, 100 and 1000 Mbps

- Supports IEEE 802.3u auto-negotiation

- Supports wire for management

Introduction

Compatibility

• PCI 2.2 and AC ’97 compliant

• Intel AGP version 3.0

ICH5R SATA IDE/RAID0 Interface

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Two SATA (Serial ATA) interfaces which are compliant with SATA

1.0 specification (1.5Gbps interface)

• Supports RAID 0

ATA RAID - Redundant Array of Independent Disk (G4C600-R

only)

• Uses HighPoint 372N RAID controller

• RAID 0, 1, 0+1 and 1.5

- RAID 1.5 performs data stripping and mirroring

simultaneously using two drives only

• Two independent IDE channels support up to 4 drives (ATA/33,

ATA/66, ATA/100, ATA/133 or EIDE)

• Supports PIO modes 0/1/2/3/4, DMA modes 0/1/2 and

UDMA modes 0/1/2/3/4/5/6

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. The

IRDA (Infrared Data Association) specification supports data

transfers of 115K baud at a distance of 1 meter.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DFI-ITOX Hauptplatine Handbücher

DFI-ITOX

DFI-ITOX G5G100-L10C Bedienungsanleitung

DFI-ITOX

DFI-ITOX EL330-DR Bedienungsanleitung

DFI-ITOX

DFI-ITOX SR330-L Bedienungsanleitung

DFI-ITOX

DFI-ITOX LR101 SERIES Bedienungsanleitung

DFI-ITOX

DFI-ITOX SR100-N Bedienungsanleitung

DFI-ITOX

DFI-ITOX G4M300-M12 Bedienungsanleitung

DFI-ITOX

DFI-ITOX G5G100-P Bedienungsanleitung

DFI-ITOX

DFI-ITOX G7B630-B Bedienungsanleitung

DFI-ITOX

DFI-ITOX G4M100-MS12 Bedienungsanleitung

DFI-ITOX

DFI-ITOX G4S300-B Bedienungsanleitung

DFI-ITOX

DFI-ITOX G4E606-P Bedienungsanleitung

DFI-ITOX

DFI-ITOX CA61 Bedienungsanleitung

DFI-ITOX

DFI-ITOX EL330-DR Bedienungsanleitung

DFI-ITOX

DFI-ITOX CB60-ZX Bedienungsanleitung

DFI-ITOX

DFI-ITOX GIC68-B Bedienungsanleitung

DFI-ITOX

DFI-ITOX G7L630-B Bedienungsanleitung

DFI-ITOX

DFI-ITOX G7V300-P Bedienungsanleitung

DFI-ITOX

DFI-ITOX G4V300-D Bedienungsanleitung

DFI-ITOX

DFI-ITOX EL109-N Bedienungsanleitung

DFI-ITOX

DFI-ITOX SB331-IPM Bedienungsanleitung

DFI-ITOX

DFI-ITOX G4H875-N Bedienungsanleitung

DFI-ITOX

DFI-ITOX G7VP2 Bedienungsanleitung

DFI-ITOX

DFI-ITOX G7VP2 Bedienungsanleitung

DFI-ITOX

DFI-ITOX NP100-N16C Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung