DFI-ITOX G7VP2 Bedienungsanleitung
37310911
G7VP2
Rev. B+
System Board
Users Manual
Copyright
This publication contains information that is protected by copyright.
No part of it may be reproduced in any form or by any means or
used to make any transformation/adaptation without the prior
written permission from the copyright holders.
This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any
express or implied warranties of merchantability or fitness for any
particular purpose.The user will assume the entire risk of the use or
the results of the use of this document. Further, the manufacturer
reserves the right to revise this publication and make changes to its
contents at any time, without obligation to notify any person or
entity of such revisions or changes.
© 1999. All Rights Reserved.
Trademarks
Microsoft®MS-DOS®, WindowsTM, Windows®95 and Windows®98
are registered trademarks of Microsoft Corporation. Intel, Pentium
and Pentium with MMX technology are registered trademarks of
Intel Corporation. Cyrix, 6x86L, 6x86MX and M II are registered
trademarks of Cyrix Corporation. AMD, K5, K6, K6-2 and K6-III are
registered trademarks of Advanced Micro Devices, Inc. IBM 6x86MX
is a registered trademark of International Business Machine
Corporation. IDT, C6 and WinChip2 are registered trademarks of
IDT Corporation. Award is a registered trademark of Award
Software, Inc. Other trademarks and registered trademarks of
products appearing in this manual are the properties of their
respective holders.
Caution:
Danger of explosion if battery incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the battery manufacturers
instructions.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to tr y to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for
help.
Notice:
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
2. Shielded interface cables must be used in order to comply with
the emission limits.
Table of Contents
Chapter 1 - Introduction
1.1 Features and Specifications..................................................................................
1.2 Package Checklist.........................................................................................................
Chapter 2 - Hardware Installation
2.1 System Board Layout .............................................................................................
2.2 System Memory.............................................................................................................
2.3 DIP Switch and Jumper Settings of the Processors...................
2.4 Jumper Settings for Clearing CMOS Data..........................................
2.5 Jumper Settings for Power Supply Type...................................................
2.6 Jumper Settings for ATX Power-On/Off Select...............................
2.7 Jumper Settings for SDRAM Clock (DIMM)......................................
2.8 Jumper Settings for Watchdog Timer.........................................................
2.9 Connecting the Ribbon Cables and Wires of the Ports
and Connectors.............................................................................................................
Chapter 3 - Award BIOS Setup Utility
3.1 The Basic Input/Output System.....................................................................
3.1.1 Standard CMOS Setup....................................................................
3.1.2 BIOS Features Setup..........................................................................
3.1.3 Chipset Features Setup....................................................................
3.1.4 Power Management Setup............................................................
3.1.5 PNP/PCI Configuration....................................................................
3.1.6 Load Fail-Safe Settings......................................................................
3.1.7 Load Optimal Settings......................................................................
3.1.8 Integrated Peripherals.........................................................................
3.1.9 Supervisor Password..........................................................................
3.1.10 User Password.........................................................................................
3.1.11 IDE HDD Auto Detection...........................................................
3.1.12 Save & Exit Setup.................................................................................
3.1.13 Exit Without Saving..............................................................................
6
10
34
34
38
42
44
48
50
50
50
54
54
55
56
56
11
12
12
19
20
21
22
23
24
62
62
63
63
64
65
65
57
60
61
Chapter 4 - Supported Softwares
4.1 Desktop Management Interface....................................................................
4.2 System Health Monitor Utility..........................................................................
4.3 Drivers...................................................................................................................................
Appendix A - Identifying Processors
A.1 Intel Processors.............................................................................................................
A.2 Cyrix Processors..........................................................................................................
A.3 IBM Processors.............................................................................................................
A.4 AMD Processors.........................................................................................................
A.5 IDT Processors.............................................................................................................
Appendix B - System Error Message
B.1 POST Beep.......................................................................................................................
B.2 Error Messages..............................................................................................................
Appendix C - Troubleshooting
C.1 Troubleshooting Checklist.................................................................................... 67
6
Introduction
1
1.1 Features and Specifications
1.1.1 Features
Chipset
VIA
Apollo 598MVP AGP system chipset
Processor
The system board is equipped with a switching voltage regulator
that supports 2.0V to 3.5V core voltage for various processors.
AMD®K5 PR90/PR100/PR120/PR133/PR166, K6-166/200/233/
266/300, K6-2/250/266/300/333/350/366/380/400 or K6-III/
400
Intel Pentium
90/100/120/133/150/166/200MHz or Intel
Pentium
processor with MMXTM technology-166/200/233MHz
Cyrix®6x86L PR150+/PR166+/PR200+, 6x86MX-PR166/
PR200/PR233/PR266 or M II-300/333/350/400
IBM® 6x86MX-PR200/PR233/PR266/PR300/PR333
IDT®C6-180/200/225/240 or WinChip2-200/225/233/240/
266/300
System Memory
The system board supports 8MB to 256MB of memory. It is
equipped with two DIMM sockets. The 168-pin DIMM sockets use
x64 EDO (60/70ns), SDRAM (10/12/13ns) or PC SDRAM (PC-
100 SDRAM for 100MHz external system bus clock processors),
3.3V.
DIMMs
1MBx64
2MBx64
4MBx64
8MBx64
16MBx64
Memory Size
8MB
16MB
32MB
64MB
128MB
Chapter 1 - Introduction
7
1
Introduction
Level 2 Cache Memory
512KB pipeline burst, direct map write-back cache installed on
the system board.
Expansion Slots
The system board is equipped with 1 dedicated PCI slot, 5
dedicated 16-bit ISA slots and 1 shared PCI/ISA slot. All PCI and
ISA slots are bus masters.
Desktop Management Interface (DMI)
The system board comes with a DMI 2.0 built into the BIOS. The
DMI utility in the BIOS automatically records various information
about your system configuration and stores these information in the
DMI pool, which is a part of the system board's Plug and Play
BIOS. DMI, along with the appropriately networked software, is
designed to make inventory, maintenance and troubleshooting of
computer systems easier. Refer to Chapter 4 for instructions on
using the DMI utility.
Connectors
2 connectors for external USB ports
1 connector for IrDA interface
2 serial ports
1 parallel port
2 IDE connectors
1 floppy connector
1 PS/2 mouse port
1 PS/2 or AT keyboard port
1 5-pin AT keyboard connector
1 20-pin ATX power supply connector
1 12-pin standard AT power supply connector
PCI Bus Master IDE Controller
Two PCI IDE interfaces support up to four IDE devices
Ultra DMA/33 supported (Synchronous Ultra DMA mode -
data transfer rate up to a maximum of 33MB/sec.)
PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up
to 16.6MB/sec.)
8
Introduction
1
Bus mastering reduces CPU utilization during disk transfer
Supports ATAPI CD-ROM, LS-120, ZIP and SCSI sequential
boot-up
IrDA Interface
The system board is equipped with an IrDA connector for wireless
connectivity between your computer and peripheral devices. It
supports infrared peripheral devices that meet the ASKIR or HPSIR
standard.
USB Ports
The system board is equipped with two connectors for external
USB ports. USB allows data exchange between your computer and
a wide range of simultaneously accessible external Plug and Play
peripherals.
BIOS
Award BIOS, Windows
95/98 Plug and Play compatible
Flash EPROM for easy BIOS upgrades
1.1.2 Intelligence
Monitors Processor Temperature and Overheat Alarm
The system board is able to detect the temperature of the
processor. An alarm will sound in case of processor overheat.
Monitors Processor/Chassis Fan Speed and Failure Alarm
The system board is able to detect the fan speed (RPM-Revolutions
Per Minute) of the processor and chassis fans, and alerts you to
attend to any irregularity that may damage your system.
Monitors Power Voltages and Failure Alarm
The system board is able to detect the output voltage of the power
supply. An alarm will sound warning you of voltage irregularity.
Automatic Fan Control
With the systems power switched on, the processors fan will rotate
only if the temperature of the processor is over 25oC.
9
1
Introduction
Dual Function Power Button (ATX power supply only)
Depending on the setting in the BIOS setup, this switch will allow
your system to enter the Soft-Off or Suspend mode.
RTC Timer to Power-on the System (ATX power supply only)
The RTC installed on the system board allows your system to
automatically power-on on the set date and time.
Watchdog Timer
The system board is designed for Industrial PC applications. It
supports the Watchdog Timer function allowing your application to
regularly clear the system at the set time interval. If the system
hangs or fails to function, it will reset at the set time interval so that
your system will continue to operate. Refer to Jumper Settings for
Watchdog Timer in chapter 2 of this manual for more information.
8 step counter (0.5/1/2/4/8/16/32/64 sec)
Virus Protection
Most viruses today destroy data stored in hard drives. The system
board is designed to protect the boot sector and partition table of
your hard disk drive.
10
Introduction
1
1.2 Package Checklist
The system board package contains the following items:
þThe system board
þA users manual
þSerial, mouse and printer por t cables
Option 1:
- One card-edge bracket with a 9-pin and 25-pin serial port
cables
- One card-edge bracket with a 25-pin printer port cable and
a PS/2 mouse port cable
Option 2:
- One card-edge bracket with two 9-pin serial port cables
and a PS/2 mouse port cable
- One 25-pin printer port cable for chassis mounting
þOne 40-pin IDE hard disk cable
þOne 34-pin floppy disk drive cable
þOne CD
¨One card-edge bracket with two USB ports (optional)
If any of these items are missing or damaged, please contact your
dealer or sales representative for assistance.
Andere Handbücher für G7VP2
1
Inhaltsverzeichnis
Andere DFI-ITOX Hauptplatine Handbücher
DFI-ITOX
DFI-ITOX G5G100-L10C Bedienungsanleitung
DFI-ITOX
DFI-ITOX NP100-N16C Bedienungsanleitung
DFI-ITOX
DFI-ITOX EL630-NR Bedienungsanleitung
DFI-ITOX
DFI-ITOX G4H875-N Bedienungsanleitung
DFI-ITOX
DFI-ITOX SR100-N Bedienungsanleitung
DFI-ITOX
DFI-ITOX CA61 Bedienungsanleitung
DFI-ITOX
DFI-ITOX SB331-IPM Bedienungsanleitung
DFI-ITOX
DFI-ITOX CB60-ZX Bedienungsanleitung
DFI-ITOX
DFI-ITOX G4E606-P Bedienungsanleitung
DFI-ITOX
DFI-ITOX 586ITOX Bedienungsanleitung
DFI-ITOX
DFI-ITOX G7VP2 Bedienungsanleitung
DFI-ITOX
DFI-ITOX G4C600-R Bedienungsanleitung
DFI-ITOX
DFI-ITOX SR330-L Bedienungsanleitung
DFI-ITOX
DFI-ITOX LR101 SERIES Bedienungsanleitung
DFI-ITOX
DFI-ITOX G5G100-P Bedienungsanleitung
DFI-ITOX
DFI-ITOX G4M300-M12 Bedienungsanleitung
DFI-ITOX
DFI-ITOX EL330-DR Bedienungsanleitung
DFI-ITOX
DFI-ITOX G4S300-B Bedienungsanleitung
DFI-ITOX
DFI-ITOX G4M100-MS12 Bedienungsanleitung
DFI-ITOX
DFI-ITOX G7L630-B Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
