DFI 586OP Bedienungsanleitung
586OP
System Board
User’s Manual
-D24941007-
vCopyright1994,byDFIInc.
All rights reserved.
No part of this document may be copied or reproduced
in any form or by any means without the prior written
consent of DFI, Inc.
DFI, Inc. makes no warranties with respect to this
documentation and disclaims any implied warranties of
merchantability, quality, or fitness for any particular
purpose. The information in this document is subject to
change without notice. DFI, Inc. reserves the right to
make revisions to this publication and to make changes
to any and/or all parts of its content, at any time,
without obligation to notify any person or entity of such
changes. Further, DFI, Inc. assumes no responsibility
for any errors that may appear in this document.
DFI is a registered trademark, and 586OP is a trade-
mark of Diamond Flower, Inc. All other product names
mentioned are trademarks or registered trademarks of
their respective companies.
vFCCStatementonClassB
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential
installation. This equipment generates, uses, and can
radiate radio frequency energy and if not installed and
used in accordance with the instruction manual may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
the receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio TV
technician for help.
Notice:
1. The changes or modification not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to
comply with the emission limits.
v Table of Contentsv
Introduction ..............................................................................
Features and Specifications ................................................
Package Checklist ...............................................................
Installation Overview ...............................................................
Preparing the Area ..............................................................
Handling the System Board ................................................
Tips in Handling the System Board ..............................
Hardware Installation..........................................................
Memory Installation ......................................................
Installing the Modules ............................................
Board Configuration ......................................................
Jumper Settings for CMOS Clean, Display Type
and PS/2 Mouse................................................
Jumper Settings for Parallel Port ...........................
Cache Configuration ..............................................
Jumper Settings for Cache Memory .................
CPU Installation ............................................................
Jumper Settings for CPU .......................................
Installing Upgrade CPUs .......................................
Built-in Ports ........................................................................
Serial Ports ...................................................................
Parallel Port ..................................................................
Floppy Disk Drive Connector ........................................
IDE Hard Disk Connector .............................................
PS/2 Mouse Port ..........................................................
Installing Expansion Cards .................................................
Installing the System Board ................................................
1-1
1-2
1-4
2-1
2-1
2-2
2-2
.2-2
2-2
2-6
2-7
2-8
2-11
2-13
2-14
2-16
2-17
2-18
2-23
2-24
2-25
2-27
2-28
2-31
2-32
2-33
Initial Setup Program ................................................................
Award BIOS CMOS Setup Utilities ......................................
Standard CMOS Setup ..................................................
BIOS Features Setup .....................................................
Chipset Features Setup .................................................
PCI Configuration Setup ................................................
Load BIOS Defaults .......................................................
Load Setup Defaults ......................................................
Password Setting ...........................................................
IDE HDD Auto Detection ...............................................
Save & Exit Setup ..........................................................
Exit Without Saving ........................................................
IDE Device Drivers ....................................................................
Troubleshooting Checklist ........................................ .............
Appendix A:Types of Modules .............................. ...............
Appendix B:System Error Report .........................................
Appendix C:Memory & I/O Maps ...........................................
Appendix D:PCI I/O Pin Assignments ..................................
Appendix E:ISA I/O Pin Assignments ..................................
Appendix F:Connector Pin Assignments ............................
Appendix G:Award BIOS Hard Disk Table ...........................
3-1
3-2
3-2
3-5
3-7
3-8
3-9
3-9
3-10
3-11
3-11
3-12
4-1
5-1
A-1
B-1
C-1
D-1
E-1
F-1
G-1
PCI/ISASystemBoard
vIntroduction
The 586OP system board offers several advanced fea-
tures integrated into the system board. Its design is
based on the new Peripheral Component Interconnect
(PCI) local bus and Industry Standard Architecture
(ISA) standards.
The 586OP supports a 273-pin Zero Insertion Force
(ZIF) CPU socket for PentiumTM processors running at
60MHz or 66MHz frequency. This ZIF socket allows
users to easily upgrade their CPUs. It also supports a
Flash EPROM for easy BIOS upgrades. Flash EPROM
is a memory chip for the storage of BIOS which can be
erased in bulk or modified using a software utility.
The 586OP is equipped with four PCI and four ISA
slots, of which one pair is shared.
Equipped with two built-in PCI IDE connectors, the
586OP system board can control four drives and sup-
ports fast Mode 3 hard drives and hard drives larger
than 528MB under DOS. The system board is also
equipped with two serial ports, an ECP/EPP parallel
port, a floppy disk drive controller, and one mini-DIN-6
connector for the PS/2 mouse.
The 586OP can be configured to twenty-two different
memory sizes ranging from 2MB to 128MB using
256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 and
8Mx36 72-pin SIM modules.
1-1 uIntroduction
586OP
Features and Specifications
Introduction u1-2
Processor
•
Intel Pentium
TM 60/66MHz
Chipset
•OPTI: Python chipset
82C546, 82C547 - system and cache controller
82C606 - data buffer
82C206 - IPC controller
82C822 - PCI bridge
Architecture
•PCI/ISA
PCI IDE Interface
•Fast PCI local-bus interface
•Supports fast Mode 3 (Enhanced IDE) hard drives
•Two IDE connectors to control four drives (e.g. two
HDDs, one tape drive and one CD-ROM)
•Uses NS PC87410 PCI IDE chip
Super I/O Interface
•Two NS16C550A-compatible serial ports
•PS/2 mouse port
•One parallel port with EPP and ECP support
•Supports 360KB, 720KB, 1.2MB, 1.44MB and
2.88MB floppy drives
•Uses NS PC87332VF super-I/O controller
BIOS
•Award Plug & Play BIOS
•Flash EPROM for easy BIOS upgrades
•Supports IDE HDDs larger than 528MB under DOS
(LBA mode only)
PCI/ISASystemBoard
1-3 uIntroduction
Cache Memory
•256K, 512K or 1MB direct map write-back or
write-through cache
•Uses 32Kx8, 64Kx8 or 128Kx8 SRAM
Memory Onboard
•Up to 128MB (depends on the operating system)
•Four 72-pin SIMM sockets
•Supports single and/or double density SIMMs
•256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 or
8Mx36 SIMMs
•Supports 60ns or 70ns fast page mode DRAM
Expansion Slots
•Three dedicated PCI slots
•One shared PCI/ISA slot
•Three dedicated 16-bit ISA slots
Due to the size of the CPU with accompanying
heatsink/fan component, the following slots have
size limitations:
ISA slots 2, 3 and 4 will be limited to 2/3 length
ISA cards.
PCI slots 1 and 2 will be limited to 3/4 length PCI
cards.
ZIF Socket
•273-pin ZIF socket (Intel Socket 4)
Board Dimensions
•33cm (12.87") x 22cm (8.58")
Baby AT form factor
586OP
Package Checklist
The 586OP package contains the following items:
•The 586OP system board
•The 586OP user’s manual
•Two IDE driver diskettes
•One 34-pin floppy disk drive cable
•Two 40-pin IDE hard disk cables
•One 25-pin printer port cable for chassis mounting
•One card-edge bracket with serial and mouse port
cables
If any of these items is missing or damaged, please
contact your dealer or sales representative for assistance.
Introduction u1-4
PCI/ISASystemBoard
vInstallation Overview
This chapter summarizes the steps in installing the
586OP system board into your system unit. It also
includes a description of the area in which you must
work and directions for memory installation. Before
installing the system board, obtain the memory you plan
to install. Please refer to the memory chart on pages 2-3
and 2-4 for the number and type of SIM modules
needed for the amount of memory you require.
Preparing the Area
Before unpacking the system board, make sure the
location you have selected is relatively free of dust and
static electricity. Excessive exposure to dust, static
electricity, direct sunlight, excessive humidity, extreme
cold and water can damage the operational capabilities
of your system board. Avoid soft surfaces such as beds
and carpeted floors which can hinder air circulation.
These areas also attract static electricity which can
damage some circuits on your system board.
Be sure that the power source has a properly grounded,
three-pronged socket. It is essential that the power
connection be properly grounded for correct functioning
of your system board. For further protection, we recom-
mend that you use a surge suppressor. This will protect
the system board from damage that may result from a
power surge on the line.
Move items that generate magnetic fields away from
your system board, since magnetic fields can also
damage your system board. Once you have selected the
ideal location, unpack the 586OP system board care-
fully.
2-1 uInstallation Overview
Inhaltsverzeichnis
Andere DFI Hauptplatine Handbücher
DFI
DFI PB64-BX Bedienungsanleitung
DFI
DFI PE11-TC Bedienungsanleitung
DFI
DFI G5C630-DR Bedienungsanleitung
DFI
DFI CS35-EC Bedienungsanleitung
DFI
DFI G5M300-P Bedienungsanleitung
DFI
DFI BE170 Bedienungsanleitung
DFI
DFI G7V600-B Bedienungsanleitung
DFI
DFI ICX610-C621A Bedienungsanleitung
DFI
DFI 748-AL Bedienungsanleitung
DFI
DFI Infinity NF-ULTRA-M2 Bedienungsanleitung
DFI
DFI CB50-V3 Bedienungsanleitung
DFI
DFI CMS330-Q470E/H420E Bedienungsanleitung
DFI
DFI CS170-Q370/C246 Bedienungsanleitung
DFI
DFI CS100 Series Bedienungsanleitung
DFI
DFI PT332-DRM Bedienungsanleitung
DFI
DFI CA61 Bedienungsanleitung
DFI
DFI M8MP553 Bedienungsanleitung
DFI
DFI P2XBL/E Bedienungsanleitung
DFI
DFI LanParty UT NF590 SLI-M2R/G Bedienungsanleitung
DFI
DFI NB76-BC Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
