DFI M8M051 Bedienungsanleitung

M8M051

A-609-M-2040

2.5" Pico-ITX Motherboard

User’s Manual

2User's Manual | M8M051

This publication contains information that is protected by copyright. No part of it may be

reproduced in any form or by any means or used to make any transformation/adaptation

without the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes

no representations or warranties with respect to the contents or use of this manual and

specifically disclaims any express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or the results of the use of

this document. Further, the manufacturer reserves the right to revise this publication and make

changes to its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

3User's Manual | M8M051

Table of Contents

Chapter 1 - Introduction................................................................................................................6

Specifications ......................................................................................................................... 6

Features ..................................................................................................................................7

Chapter 2 - Hardware Installation................................................................................................8

Board Layout...........................................................................................................................8

Installing the Heat Sink................................................................................................... 9

Jumper Settings ...................................................................................................................10

Boot-CFG (JP1)..............................................................................................................10

Audio (JP4) ....................................................................................................................10

LED Backlight (JP5) ......................................................................................................11

External I/O Ports.................................................................................................................12

+12V DC-in .....................................................................................................................12

USB 3.1 Gen 1 & Micro USB 2.0...................................................................................13

LAN (RJ-45)....................................................................................................................13

COM 3 (RS485)..............................................................................................................14

Graphics Display............................................................................................................14

Internal I/O Connectors .......................................................................................................15

J3 USB 2.0 Headers (3/4).............................................................................................15

J10 Debug(COM1).........................................................................................................15

J8 I²C ..............................................................................................................................16

J5 DIO.............................................................................................................................16

J11 LVDS........................................................................................................................17

J9 COM2 / COM4 ..........................................................................................................18

J7 Front Panel................................................................................................................18

J1 Battery.......................................................................................................................19

CN12 CANbus 2.0..........................................................................................................19

Expansion Slots....................................................................................................................20

SIM Slot / I2C Connector..............................................................................................20

microSD Socket .............................................................................................................20

Chapter 3 - Software User Guide...............................................................................................21

Yocto OS - Flash Images into eMMC/SD card using UUU tool ........................................21

Windows winusb driver install for Windows UUU tool......................................................23

Flash image into SD card ....................................................................................................24

Android OS - Flash Images into eMMC/SD card using UUU tool.....................................25

Software Features ................................................................................................................26

General Support List......................................................................................................26

Linux AP/API Support List ............................................................................................26

Yocto Support List.........................................................................................................26

Android Support List .....................................................................................................28

4User's Manual | M8M051

About this Manual

This manual can be downloaded from the website.

The manual is subject to change and update without notice, and may be based on editions

that do not resemble your actual products. Please visit our website or contact our sales

representatives for the latest editions.

Warranty

1. Warranty does not cover damages or failures that arise from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper

installation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any

circumstances, attempt to perform service, adjustments or repairs on the product,

whether in or out of warranty. It must be returned to the purchase point, factory or

authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequential damages to

the product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in

handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you

are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components,

contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or

connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other

components. Perform the upgrade instruction procedures described at an ESD

workstation only. If such a station is not available, you can provide some ESD

protection by wearing an antistatic wrist strap and attaching it to a metal part

of the system chassis. If a wrist strap is unavailable, establish and maintain

contact with the system chassis throughout any procedures requiring ESD

protection.

Safety Measures

• To avoid damage to the system, use the correct AC input voltage range.

• To reduce the risk of electric shock, unplug the power cord before removing the

system chassis cover for installation or servicing. After installation or servicing, cover

the system chassis before plugging the power cord.

5User's Manual | M8M051

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• 1 M8M051 board

• 1 Terminal block for RS485 (COM3)

• Heat spreader (Height: 11mm)

Note: The items are subject to change in the developing stage.

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance with the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

When installing the system board in a new system, you will need at least the following internal

components.

• Power adapter

External system peripherals may also be required for navigation and display, including at least a

keyboard, a mouse and a video display monitor.

Chapter 1

INTRODUCTION

User's Manual | M8M051

Chapter 1 - Introduction

XSpecifications

SYSTEM Processor i.MX 8M applications processors

NXP i.MX 8M Quad Cortex-A53, 1.5GHz (Commercial)

NXP i.MX 8M Dual Cortex-A53, 1.5GHz (Commercial)

NXP i.MX 8M Quad Cortex-A53, 1.3GHz (Industrial)

NXP i.MX 8M Dual Cortex-A53, 1.3GHz (Industrial)

Memory 2GB/4GB Memory Down

Single Channel LPDDR4 up to 3200 MHz

GRAPHICS Controller GC7000 Lite

Feature OpenVG 1.1, OGL ES 3.1, Vulkan, OCL 1.2 FP

VPU Decode: 4Kp60 HEVC H.265, VP9, 4Kp60 H.264

Display 1 x HDM (default)

1 x LVDS

HDMI: resolution up to 4096x2160 @60Hz

LVDS: resolution up to 1920x1080 @60Hz

Single Display HDMI or LVDS

EXPANSION Interface 1 x M.2 B key 3042/2242 (USB 3.1 Gen1)

Nano SIM slot support (available upon request)

1 x M.2 E key 2230 (PCIe x1/USB 2.0)

AUDIO Audio Codec SGTL5000

ETHERNET Controller 1 x AR8035 Ethernet (10/100/1000Mbps)

External I/O Ethernet 1 x GbE (RJ-45)

Serial 1 x RS485

USB 2 x USB 3.1 Gen1

1 x Micro USB 2.0 (Download mode)

Display 1 x HDMI

INTERNAL I/O Serial 1 x RS232

1 x RS-232/422/485 (2 x 6 pin header, 1.27mm pitch)

USB 2 x USB 2.0 (1.27mm pitch)

Display 1 x LVDS LCD Panel Connector

1 x Backlight Power

Audio 1 x Audio (Line-out/Mic-in, 2.00mm pitch)

eMMC Support eMMC 5.1 16GB on board (default)

Support up to 64GB (opt.)

SD 1 x Micro SD Slot

DIO 1 x 8-bit DIO (2 x 6 header, 1.27mm pitch)

I²C 1 x I²C (1.27mm pitch)

CANBus 1 x CANBus 2.0

WATCHDOG

TIMER

Output &

Interval

System Reset, Programmable via Software from 1 to 255 Seconds

POWER Type Single 12V +/-10% DC

Connector 2-poles Terminal Block (default)

DC Jack (available upon request)

Consumption Typical: Quad:12V @ 0.2A (2.4Watt)

Max.: Quad:12V @ 0.38A (4.56Watt)

RTC Battery CR2032 Coin Cell

OS SUPPORT OS Support Yocto 2.5 on eMMC (default)

Android 9.0 (optional)

ENVIRONMENT Temperature Operating: -5 to 65°C, -30 to 80°C

Storage: -40 to 85°C

Humidity Operating: 5 to 90% RH

Storage: 5 to 90% RH

MTBF i.MX 8MQuad: 1,311,832 hrs @ 25°C; 637,427 hrs @ 45°C; 374,475 hrs @

60°C; 189,510 hrs @ 80°C

Calculation model: Telcordia Issue 4

Environment: GB, GC – Ground Benign, Controlled

Mechanism Dimensions 2.5" SBC Form Factor

100mm (3.94") x 72mm (2.83")

Height PCB: 1.6mm Top Side: 15mm, Bottom Side: 4mm

Standards and

Certifications

Certifications CE, FCC, RoHS

Country of Origin Country of

Origin

Taiwan

Chapter 1

INTRODUCTION

User's Manual | M8M051

XFeatures

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so that

your system will continue to operate.

DDR4

DDR4 delivers increased system bandwidth and improves performance. The advantages of

DDR4 provide an extended battery life and improve the performance at a lower power than

DDR3/DDR2.

Graphics

The integrated GC7000 Lite graphics engine delivers an excellent blend of graphics

performance and features to meet business needs. It provides excellent video and 3D graphics

with outstanding graphics responsiveness. These enhancements deliver the performance and

compatibility needed for today’s and tomorrow’s business applications.

Gigabit LAN

The Gigabit Ethernet Controller supports data transmission at 1Gbps.

Audio

The audio codec provides High Definition audio output.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is

supported via the onboard LAN port that uses the PCI PME (Power Management Event) signal.

However, if your system is in the Suspend mode, you can power-on the system only through an

IRQ or DMA interrupt.

Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a system from the

S3 (STR - Suspend To RAM) state.

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power

Interface) specification. ACPI has energy saving features that enables PCs to implement

Power Management and Plug-and-Play with operating systems that support OS Direct Power

Management. ACPI when enabled in the Power Management Setup will allow you to use the

Suspend to RAM function.

With the Suspend to RAM function enabled, you can power-off the system at once by pressing

the power button or selecting “Standby” when you shut down Windows®without having to go

through the sometimes tiresome process of closing files, applications and operating system.

This is because the system is capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it powers-off. The operating

session will resume exactly where you left off the next time you power-on the system.

Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

USB

The system board supports the new USB 3.1 Gen 1. It is capable of running at a maximum

transmission speed of up to 5 Gbit/s, or 625 MB/s. USB 3.1 reduces the time required for data

transmission, reduces power consumption, and is backward compatible with USB 2.0. It is a

marked improvement in device transfer speeds between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

RTC Timer

The Real Time Clock (RTC) installed on the system board allows your system to automatically

power-on on the set date and time.

Chapter 2

HARDWARE INSTALLATION

User's Manual | M8M051

Chapter 2 - Hardware Installation

XBoard Layout

Note:

Some components are optional and only available upon request.

Important:

Electrostatic discharge (ESD) can damage your board, processor,

disk drives, add-in boards, and other components. Perform

installation procedures at an ESD workstation only. If such a

station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part

of the system chassis. If a wrist strap is unavailable, establish

and maintain contact with the system chassis throughout any

procedures requiring ESD protection.

Chapter 2

HARDWARE INSTALLATION

User's Manual | M8M051

Installing the Heat Sink

The CPU must be kept cool by using a heat sink, otherwise the CPU will overheat damaging

both the CPU and system board.

1. Before you install the fan / heat sink, you must apply a thermal paste onto the top of

the CPU. The thermal paste is usually supplied when you purchase the fan / heat sink

assembly. Do not spread the paste all over the surface. When you later place the heat

sink on top of the CPU, the compound will disperse evenly.

Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal

paste if the fan / heat sink already has a patch of thermal paste on its underside. Peel

the strip that covers the paste before you place the fan / heat sink on top of the CPU.

2. Place the heat sink on top of the CPU. The 4 spring screws around the heat sink, which

are used to secure the heat sink onto the system board, must match the 4 mounting

holes around the board.

3. Screw tight two of the spring screws at opposite corners into the mounting holes. And

then proceed with the other two spring screws.

XCPU

Mounting holes

Chapter 2

HARDWARE INSTALLATION

User's Manual | M8M051

XJumper Settings

Boot-CFG (JP1)

5-6 Off: EMMC@eSDHC

(default)

5-6 On: uSD@eSDHC2

1-2 Off: Internal Boot

(default)

1-2 On: Serial Downloader

Audio (JP4)

4: R-CH

1: Mic Input

2/3/5: GND

6: L-CH

The JP1 is used to determine the Boot-CFG The JP4 is used to determine the Audio

Andere Handbücher für M8M051

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI CR101-D Bedienungsanleitung

DFI

DFI WL051 Bedienungsanleitung

DFI

DFI HD310-Q87 Bedienungsanleitung

DFI

DFI CMS310-Q470E Bedienungsanleitung

DFI

DFI ADS310-R680E Series Bedienungsanleitung

DFI

DFI CA33-SC Bedienungsanleitung

DFI

DFI PL610-C622 Bedienungsanleitung

DFI

DFI COM630-B Bedienungsanleitung

DFI

DFI PB61-V3 Bedienungsanleitung

DFI

DFI SR100-L20C Bedienungsanleitung

DFI

DFI CMS632-W480E Bedienungsanleitung

DFI

DFI AL05P Bedienungsanleitung

DFI

DFI BL630-DR Bedienungsanleitung

DFI

DFI CW35-TC Bedienungsanleitung

DFI

DFI CP330-NRM Bedienungsanleitung

DFI

DFI HD620 Series Bedienungsanleitung

DFI

DFI G7L330-B Bedienungsanleitung

DFI

DFI LanParty PRO875B Bedienungsanleitung

DFI

DFI SD630-H110-000G Bedienungsanleitung

DFI

DFI FS053 Bedienungsanleitung

DFI

DFI G586IPB Bedienungsanleitung

DFI

DFI CMS631-Q470E Bedienungsanleitung

DFI

DFI AL171 Bedienungsanleitung

DFI

DFI Blood-Iron G41-T33 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung

Epson

Epson S5U13700P00C000 Bedienungsanleitung