DFI NB30-EC Bedienungsanleitung

NB30-EC/EL

NB35-EC/EL

Rev. A+

System Board

User’s Manual

54600211

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows® 98 SE, Windows® ME, Windows® 000, Windows NT®

4.0 and Windows® XP are registered trademarks of Microsoft

Corporation. Intel® and Pentium® 4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual”.

System Board

This user’s manual is for the NB30-EC, NB30-EL, NB35-EC and

NB35-EL system boards. The differences between these boards are

shown below.

NB30-EC/EL Intel 845GL

ADD slot

“EL” suppor ts onboard LAN

NB35-EC/EL Intel 845G

AGP slot

“EL” suppor ts onboard LAN

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

.1 System Board Layout ..........................................................................................

. System Memory...........................................................................................................

.3 Jumper Settings for Clearing CMOS Data........................................

.4 Jumper Settings for Wake-On-Keyboard/Mouse..................................

.5 Jumper Settings for Wake-On-USB Keyboard.......................................

.6 Jumper Settings for Selecting the CPU’s Front Side Bus......

.7 Jumper Settings for USB 6................................................................................

.8 Por ts and Connectors...........................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 CPU Frequency Control..................................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

Introduction

103

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface................................................................

4. Hardware Doctor....................................................................................................

4.3 Intel INF Update Utility for Windows 98SE/ 000/ME/

XP...........................................................................................................................................

4.4 Intel Application Accelerator for Windows......................................

4.5 Intel Graphics Drivers for Windows 98SE/NT/ME/

000/XP...........................................................................................................................

4.6 Audio Drivers and Software Application.........................................

4.7 Onboard LAN Drivers for Windows.................................................

4.8 USB .0 Driver..........................................................................................................

4.9 Microsoft DirectX 8.1 Driver.......................................................................

4.10 Drivers and Utilities Installation Notes...............................................

Appendi A - System Error Messages

A.1 POST Beep.......................................................................................................................

A. Error Messages..............................................................................................................

Appendi B - Troubleshooting

B.1 Troubleshooting Checklist....................................................................................

100

101

105

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• NB30-EC/EL

Intel® 845GL chipset

- Intel® 845GL Graphics Memor y Controller Hub (GMCH)

- Intel® 8 801DB I/O Controller Hub (ICH4)

• NB35-EC/EL

Intel® 845G chipset

- Intel® 845G Graphics Memor y Controller Hub (GMCH)

- Intel® 8 801DB I/O Controller Hub (ICH4)

Processor

The system board is equipped with Socket 478 for installing a

Pentium® 4 processor.

• Intel® Pentium® 4 processor (478-pin)

• Supports up to . GHz CPU speed

• 400/533MHz system data bus (NB35-EC/EL)

400MHz system data bus (NB30-EC/EL)

System Memory

• Two 184-pin DDR SDRAM DIMM sockets

• .5V unbuffered PC1600 (DDR 00) / PC 100 (DDR 66)

DDR SDRAM DIMM

• Supports maximum of GB system memory using 64Mbit,

1 8Mbit, 56Mbit or 51 Mbit technology

- Double-sided x16 DDR SDRAM DIMM is not supported

Chapter 1 - Introduction

Density Width

Single/Double

184-pin DDR

64 Mbit

SS/DS

64/128MB

X16

SS/DS

32MB/N

Density 128 Mbit

SS/DS

128/256MB

X16

SS/DS

64MB/N

256 Mbit

SS/DS

256/512MB

X16

SS/DS

128MB/N

512 Mbit

SS/DS

512/1024MB

X16

SS/DS

256MB/N

Introduction

Expansion Slots

The NB30-EC/EL system board is equipped with 1 ADD slot, 3 PCI

slots (1 shared with CNR slot) and 1 CNR slot.

The NB35-EC/EL system board is equipped with 1 AGP slot, 3 PCI

slots (1 shared with CNR slot) and 1 CNR slot.

The AGP slot only supports 1.5V AGP 4x (1066MB/sec. bandwidth)

add-in cards. AGP is an interface designed to support high

performance 3D graphics cards for 3D graphics applications. It

handles large amounts of graphics data with the following features:

• Pipelined memory read and write operations that hide memory

access latency.

• Demultiplexing of address and data on the bus for nearly 100

percent efficiency.

The ADD slot is used for installing an ADD (AGP Digital Display)

card.

CNR (Communication and Networking Riser) is an interface that

supports multi-channel audio, V.90 analog modem, phone-line based

networking or 10/100 Ethernet based networking riser board.

Onboard Graphics eatures

• Graphics memory

- Shares 51 K/1MB/8MB of the system memory in DOS

mode

- Uses Dynamic Video Memory Technology (DVMT) in

Windows mode

• Graphics controller

- Core frequency of 00MHz

- 350MHz integrated 4-bit RAMDAC

- Analog display up to 048x1536 @ 60Hz refresh

- 3D setup and render engine - Discrete, Triangles, Strips and

fans

- Per pixel perspective corrected texture mapping

- Software DVD at 30fps, full screen

• D graphics features

- Optimized 56-bit BLT engine

- 3 -bit alpha blended cursor

Introduction

- Programmable 3-color transparent cursor

• 3D graphics features

- 00 megapixels/sec fill rate

- Maximum 3D resolution: 1600x1 00x3 @ 85Hz

- Flat and Gouraud shading

- 16- and 4-bit Z-buffering and 16- and 4-bit W-buffering

- Vertex and programmable pixel fogging and

atmospheric effects

- Double and triple render buffer

• Software drivers

- Windows® 98SE/ 000/ME/XP

- Windows NT® 4.0

Onboard Audio eatures

• 0-bit stereo full-duplex codec with independent variable

sampling rate

• High quality differential CD input

• True stereo line level outputs

• S/PDIF-in/out interface

• 6-channel audio output

Onboard LAN eatures (NB30-EL and NB35-EL only)

• Uses Realtek RTL8100 fast ethernet controller

• Integrated IEEE 80 .3, 10BASE-T and 100BASE-TX compatible

PHY

• 3 -bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 80 .3u auto-negotiation

• Supports wire for management

Compatibility

• Microsoft PC ’98 compliant

• PCI . , CNR 1.0 “A” type and AC ’97 compliant

• Intel AGP version .0

Introduction

ATX Double Deck Ports (PC 99 color-coded connectors)

• 4 USB .0/1.1 ports

• 1 RJ45 LAN port (NB30-EL and NB35-EL only)

• 1 NS16C550A-compatible DB-9 serial port

• 1 DB-15 VGA port

• 1 DB- 5 parallel port

• 1 mini-DIN-6 PS/ mouse port

• 1 mini-DIN-6 PS/ keyboard port

• 3 audio jacks: line-out, line-in and mic-in

Connectors

• 1 connector for additional external USB .0/1.1 ports

• 1 connector for 1 external serial por t

• 1 connector for an external game/MIDI por t

• internal audio connectors (CD-in and TAD)

• 1 4-channel audio output connector

• 1 S/PDIF-in connector

• 1 S/PDIF-out connector

• 1 connector for IrDA interface

• IDE connectors

• 1 floppy drive interface supports up to two .88MB floppy

drives

• ATX power supply connectors

• 1 Wake-On-LAN connector

• 1 Wake-On-Ring connector

• CPU fan, chassis fan and second fan connectors

• 1 opened chassis alarm connector

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-1 0 and ZIP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI NS70-EC Bedienungsanleitung

DFI

DFI HD330-Q87 Bedienungsanleitung

DFI

DFI G486-EVB Bedienungsanleitung

DFI

DFI PE11-EC Bedienungsanleitung

DFI

DFI BW051 Bedienungsanleitung

DFI

DFI P5BTX/L Bedienungsanleitung

DFI

DFI M8M051 Bedienungsanleitung

DFI

DFI P4M266A-MLV Bedienungsanleitung

DFI

DFI SO630 Bedienungsanleitung

DFI

DFI G7S620-N Bedienungsanleitung

DFI

DFI G586IPC Bedienungsanleitung

DFI

DFI AK74-SC Bedienungsanleitung

DFI

DFI PS82-BC/BL Bedienungsanleitung

DFI

DFI 586ITOX Bedienungsanleitung

DFI

DFI CS350-C246 Bedienungsanleitung

DFI

DFI SU256-SCM Bedienungsanleitung

DFI

DFI AK74-SC Bedienungsanleitung

DFI

DFI PT880-ALF Bedienungsanleitung

DFI

DFI WL051-BCC-B Bedienungsanleitung

DFI

DFI CS350-C246 Bedienungsanleitung

DFI

DFI PR611-C621 Bedienungsanleitung

DFI

DFI 852GME-MGF Pro Bedienungsanleitung

DFI

DFI NS35-TC Bedienungsanleitung

DFI

DFI G7S300-B Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung