DFI P4M266A-MLV Bedienungsanleitung

P4M266A-MLV

Rev.AA+

System Board

User’s Manual

79910409

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. Intel®and Pentium®4 are registered

trademarks of Intel Corporation. VIA is a registered trademark of

VIA Technologies, Inc. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.The

autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Hyper-Threading Technology Functionality Requirements..........

1.3 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...........................................................................................

2.2 System Memory...........................................................................................................

2.3 CPU........................................................................................................................................

2.4 Jumper Settings.............................................................................................................

2.5 Rear Panel I/O Ports..............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.2 Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.................................................................

4.2 Drivers, Utilities and Software Applications.....................................

4.3 Installation Notes......................................................................................................

105

Introduction

113

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...........................................

Appendix B - Using the Suspend to RAM

Function

B.1 Using the Suspend to RAM Function...................................................

Appendix C - System Error Messages

C.1 POST Beep....................................................................................................................

C.2 Error Messages...........................................................................................................

Appendix D - Troubleshooting

D.1 Troubleshooting Checklist.................................................................................

109

115

106

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIA®chipset

- North bridge:VIA®P4M266A

- South bridge:VIA® VT8235CD

Processor

The system board is equipped with Socket 478 for installing one of

the following supported processors.

• Intel®Pentium®4 (Processor and Northwood) processor up to

3.06GHz

- Intel Hyper-Threading Technology

- FSB: 400MHz and 533MHz

• Intel®Celeron processor

- 400MHz system data bus

System Memory

• Two 184-pin DDR DIMM sockets

• Supports up to 2GB using PC1600 (DDR200) and PC2100

(DDR266) unbuffered DDR SDRAM DIMM, 2.5V type

• Uses x8/x16 512MB technology

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

• 1 AGP slot

• 3 PCI slots

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP 4x with up to 1066MB/sec. bandwidth for

3D graphics applications. AGP in this system board will deliver faster

and better graphics to your PC.

Onboard Graphics Features

• Full featured Accelerated Graphics Port (AGP) controller

- AGP specification v2.0 compliant

- Graphics Address Relocation Table (GART)

• High resolution CRT RGB interface

- 250MHz RAMDAC on chip with Gamma correction

- Horizontal/vertical sync outputs compliant with Monitor Power

Management protocols

• Integrated Savage8 2D/3D graphics controller and video

accelerator

- Optimized Shared Memory Architecture (SMA)

- 8/16/32MB frame buffer using system memory

- Single cycle 128-bit 3D architecture

- 8M triangles/second setup engine

- 140M pixels/second tri-linear fill rate

- Next generation 128-bit 2D graphics engine

- High quality DVD video playback

- 2D/3D resolutions up to 1920x1440

• 3D rendering features

- MPEG-2 video textures

• 2D hardware acceleration features

• Motion video architecture

• Full software support

Introduction

Onboard Audio Features

• Supports Microsoft®DirectSound/DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• S/PDIF-in/out compressed digital output

• 6-channel audio output via software

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to an

analog format. This prevents the quality of the audio signal from

degrading whenever it is converted to analog. S/PDIF is usually

found on digital audio equipment such as a DAT machine or audio

processing device.The S/PDIF connector on the system board sends

surround sound and 3D audio signal outputs to amplifiers and

speakers and to digital recording devices like CD recorders.

6-channel Audio

The audio jacks at the rear panel will support 6-channel audio only

when the audio utility is configured to support this function.The mic-

in at the rear will be disabled. Use the front audio’s mic-in jack.

Onboard LAN Features

• Integrated LAN controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• 32-bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Introduction

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. The

IRDA (Infrared Data Association) specification supports data

transfers of 115K baud at a distance of 1 meter.

USB Ports

The system board supports USB 2.0 and USB 1.1. USB 1.1

supports 12Mb/second bandwidth while USB 2.0 supports 480Mb/

second bandwidth providing a marked improvement in device trans-

fer speeds between your computer and a wide range of simultane-

ously accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows®98/2000/ME/XP Plug and Play

compatible

• Supports SCSI sequential boot-up

• Supports DMI 2.0 function

• 4Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI PB50-ZX Bedienungsanleitung

DFI

DFI NS70-EC Bedienungsanleitung

DFI

DFI G486VPB Bedienungsanleitung

DFI

DFI COM630-B Bedienungsanleitung

DFI

DFI COM331-B Bedienungsanleitung

DFI

DFI G486VPC Bedienungsanleitung

DFI

DFI LANPARTY UT 915P-T12 Bedienungsanleitung

DFI

DFI 486-OCV Plus Bedienungsanleitung

DFI

DFI CD951-C Series Bedienungsanleitung

DFI

DFI LanParty DK 790GX-M2RS Bedienungsanleitung

DFI

DFI 586IHX Bedienungsanleitung

DFI

DFI P5BV3+/e Bedienungsanleitung

DFI

DFI CMS630-Q470ECRM Bedienungsanleitung

DFI

DFI AD76 RAID Bedienungsanleitung

DFI

DFI CMS330-Q470E Bedienungsanleitung

DFI

DFI C586VX Bedienungsanleitung

DFI

DFI SD330 Bedienungsanleitung

DFI

DFI CS632-C246 Bedienungsanleitung

DFI

DFI KD630-H110 Bedienungsanleitung

DFI

DFI PS82-BC/BL Bedienungsanleitung

DFI

DFI LT600-DR/D/L Bedienungsanleitung

DFI

DFI CMS630-W480E Bedienungsanleitung

DFI

DFI AL102 Bedienungsanleitung

DFI

DFI SB332-C Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung