DFI PT880-ALE Bedienungsanleitung

PT880-ALE

PT800-ALE

Rev. A+

System Board

User’s Manual

79300349

This publication contains information that is protected by copy-

right. No part of it may be reproduced in any form or by any

means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. Intel®, Pentium®4 and Celeron are regis-

tered trademarks of Intel Corporation. VIA is a registered trade-

mark of VIA Technologies, Inc. Award is a registered trademark of

Award Software, Inc. Other trademarks and registered trademarks

of products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in ac-

cordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual”.

System Board

This user’s manual is for the PT880-ALE and PT800-ALE system

boards. The only difference between these boards is the PT880-

ALE system board supports dual channel memory interface.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications.................................................................................

1.2 Hyper-Threading Technology Functionality Requirements...

1.3 Package Checklist...........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...........................................................................................

2.2 System Memory...........................................................................................................

2.3 CPU........................................................................................................................................

2.4 Jumper Settings.............................................................................................................

2.5 Rear Panel I/O Ports..............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility....................................................................................

3.2 VIA RAID BIOS Setting Utility........................................................................

3.3 Updating the BIOS.......................................................................................................

Introduction

109

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface................................................................

4.2 Drivers, Utilities and Software Applications................................

4.3 Installation Notes.......................................................................................................

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology....................................

Appendix B - Using the Suspend to RAM

Function

B.1 Using the Suspend to RAM Function................................................

Appendix C - System Error Messages

C.1 POST Beep.......................................................................................................................

C.2 Error Messages.............................................................................................................

Appendix D - Troubleshooting

D.1 Troubleshooting Checklist...............................................................................

101

105

111

102

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• PT880-ALE

- North bridge: VIA®PT880

Advanced high performance 128-bit DDR DRAM control-

ler

- South bridge: VIA® VT8237

• PT800-ALE

- North bridge: VIA®PT800

- South bridge: VIA® VT8237

Processor

The system board is equipped with Socket 478 for installing one

of the following supported processors.

• Intel®Pentium®4 Processor with Hyper-Threading Technology

- 800MHz/533MHz system data bus

• Intel®Pentium®4 Northwood processor

- 533MHz/400MHz system data bus

• Intel®Celeron Northwood processor (478-pin)

- 400MHz system data bus

System Memory

• Supports dual channel (128-bit wide) memory interface

(PT880-ALE only)

• Two 184-pin DDR DIMM sockets

• Supports up to 2GB using PC1600 (DDR200), PC2100

(DDR266), PC2700 (DDR333) and PC3200 (DDR400)

unbuffered DDR SDRAM DIMM, 2.6V type

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

• 1 AGP slot

• 5 PCI slots

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP 8x with up to 2133MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better

graphics to your PC.

Onboard Audio Features

• AC’97 2.2 extension compliant codec

• Supports Microsoft®DirectSound/DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• S/PDIF-in/out compressed digital output

• 6-channel audio output via software

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to

an analog format. This prevents the quality of the audio signal

from degrading whenever it is converted to analog. S/PDIF is usu-

ally found on digital audio equipment such as a DAT machine or

audio processing device. The S/PDIF connector on the system

board sends surround sound and 3D audio signal outputs to am-

plifiers and speakers and to digital recording devices like CD re-

corders.

6-channel Audio via Software

The audio jacks at the rear panel will support 6-channel audio

only when the audio utility is configured to support this function.

The mic-in at the rear will be disabled. Use the front audio’s mic-

in jack.

Introduction

Onboard LAN Features

• Phy fast ethernet controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• 32-bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Serial ATA (SATA) IDE Interface with RAID

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Two SATA (Serial ATA) interfaces which are compliant with

SATA 1.0 specification (1.5Gbps interface)

• Supports RAID 0, RAID 1 and JBOD

PCI Bus Master IDE Controller

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

USB Ports

The system board supports USB 2.0 and USB 1.1. USB 1.1 sup-

ports 12Mb/second bandwidth while USB 2.0 supports 480Mb/

second bandwidth providing a marked improvement in device

transfer speeds between your computer and a wide range of si-

multaneously accessible external Plug and Play peripherals.

Introduction

BIOS

• Award BIOS, Windows®98/2000/ME/XP Plug and Play

compatible

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 4Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on

using the DMI utility.

Rear Panel I/O Ports (PC 99 color-coded connectors)

• One PS/2 mouse port

• One PS/2 keyboard port

• One DB-9 serial port

• One DB-25 parallel port

• 2 S/PDIF RCA jacks (S/PDIF-in and S/PDIF-out)

• Four USB 2.0/1.1 ports

• One RJ45 LAN port

• Three audio jacks: line-out, line-in and mic-in

I/O Connectors

• Two connectors for 4 additional external USB 2.0/1.1 ports

• One front audio connector for external line-out and mic-in

jacks

• One CD-in internal audio connector

• Two Serial ATA connectors

• Two IDE connectors

• One floppy connector

• Two ATX power supply connectors

• Two fan connectors

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI WL051 Bedienungsanleitung

DFI

DFI LanParty UT nF3 250 Gd Bedienungsanleitung

DFI

DFI MB630-CRM Bedienungsanleitung

DFI

DFI CW35-TC Bedienungsanleitung

DFI

DFI SB330-CRM Bedienungsanleitung

DFI

DFI P2XBL/E Bedienungsanleitung

DFI

DFI CS630-H310 Bedienungsanleitung

DFI

DFI CA63-SN Bedienungsanleitung

DFI

DFI LanParty PRO875B Bedienungsanleitung

DFI

DFI NP100-N16C Bedienungsanleitung

DFI

DFI FS051 Bedienungsanleitung

DFI

DFI CA100-D Bedienungsanleitung

DFI

DFI MB331-CRM Bedienungsanleitung

DFI

DFI ADN171 Bedienungsanleitung

DFI

DFI CA64-TC Bedienungsanleitung

DFI

DFI COM330-B Bedienungsanleitung

DFI

DFI CS350-C246 Bedienungsanleitung

DFI

DFI NS80-EA Bedienungsanleitung

DFI

DFI PT332-DRM Bedienungsanleitung

DFI

DFI GIC68-D Bedienungsanleitung

DFI

DFI HD636-H81CS Bedienungsanleitung

DFI

DFI LanParty NF3 Ultra-DF Bedienungsanleitung

DFI

DFI PM12-TC Bedienungsanleitung

DFI

DFI BW051 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung