TYPE OF PLANTS RECOMMENDED NUMBER OF DRIPPERS AND SPACING
Flowers
Vegetables
Small shrubs
and roses (up to two feet high)
Medium shrubs and
trees (two to four feet high)
Large shrubs and trees
(four to six feet high)
In sandy or loamy soil, place one, 1-GPH dripper every 10″to 12″. In clay soil, place
one, 1-GPH dripper every 16″to 20″.
In sandy or loamy soil, place one, 1-GPH dripper every 10″to 12″. In clay soil, place
one, 1-GPH dripper every 16″to 20″
In sandy or loamy soil, place one, 2-GPH dripper per plant. In clay soil, place two,
1-GPH drippers per plant 16″to 20″apart.
In sandy or loamy soil, place two, 1-GPH drippers per plant 10″to 12″apart. In clay
soil, place two, 1-GPH drippers per plant 16″to 20″apart.
In sandy or loamy soil, place three to four, 1-GPH drippers per plant 10″to 12″apart.
In clay soil, place three to four, 1-GPH drippers 16″to 20” apart.
Faucet connection:
Begin the installation at the water source by attaching
the backow preventer to your faucet , and then
attach the 25-PSI preset pressure regulator to the
backow preventer. Connect the poly tubing to the
3/4″swivel adapter and attach it to the pressure
regulator by turning “clockwise” until hand tight.
If you wish to automate the system, please select
a DIG battery or solar powered timer (model B09D,
B092A or EVO100), available online or in a store
near you.
Drip tubing layout:
Before installing the 1/2″poly tubing, uncoil the roll
and lay it out in direct sunlight (if possible) for 30
to 40 minutes. This will make it more pliable and
easier to work into the compression ttings during
installation.
Lay out the 1/2″poly tubing and run it next to as
many plants as possible. Secure the drip tubing to the
soil with the 1/2″drip tubing stakes. Install the poly
tubing in a gentle S curve to allow for contraction
at low to high temperatures.
Connect the 1/2″ drip ttings
Use 1/2″ tees (part #C35) and elbows (part #C36)
throughout the layout as needed. To install the 1/2″
compression ttings, cut the poly tubing with a hand
pruner, being careful to keep dirt from entering
the line. Hold the tting in one hand and the poly
tubing in the other and force the poly tubing into the
compression tting by moving it from side to side.
Note: Open the faucet and ush out the poly drip tubing
through the ends before installing the drip emitters.
Drip emitter installation:
The drip emitters can be installed along the poly
tubing at varying or specic spacings, depending on
the layout of the plants. To ensure high uniformity,
take care not to exceed the recommendations
provided in the kit specications.
To install the drip emitters, use one or both of the
two options:
Option 1:
Installing the drip emitters into the 1/2″poly tubing
Insert the drip emitters directly into the 1/2″tubing:
Punch a hole into the side of the poly tubing using the
small punch (part #D44). Snap the barbed side of the
drip emitter into the hole after the lines have been
ushed.
EVO 100
Solar Powered Hose
End Timer. Optional -
not included.
D52 Y-Splitter
Optional -
not included
B09D or B092A
Battery Powered Hose
End Timers. Optional -
not included.
1
2
3
1
2
3
SPECIFICATION
• Operating pressure: 10 to 45 PSI
• Recommended operating pressure: 25 PSI
(use with model D46 25-PSI pressure regulator)
• Flow rates and color codes:
- 1 GPH (4 L/H) color code - black
- 2 GPH (8 L/H) color code - green
- 4 GPH (12 L/H) color code - red
• Maximum recommended ow rate:
220 GPH (3.7 GPM)
• Poly tubing length and size:
50′x 1/2″with .600″ID x .700″OD
• Micro tubing length and size: 50′x 1/4″
• Total ow rate for this kit: 32 GPH (.53 GPM)
Option 2:
Installing the drip emitters into the 1/4″micro tubing
Extend the drip emitters using 1/4″micro tubing to reach
plants that are not near the 1/2″poly tubing: First, run a
length of micro tubing from the 1/2″poly tubing to the
plant and cut it. Then, insert a 1/4″barbed connector
(part #H80A) into the micro tubing. Punch a hole into the
1/2″poly tubing and insert the 1/4″barb into the poly
tubing. At the other end of the micro tubing, insert the
barbed side of the drip emitter after the lines have been
ushed. Add a stabilizer stake and secure to the ground.
Use the 1/4″barbed valve for manual control of individual
line of micro tubing.
Initial system start-up
Turn the water on again and ush the line[s]; this will
ush out any dirt or debris that may be in the line[s]. Close
the end of the poly tubing with the gure "8" hose end
(part #F68B).
Test and inspect the system to identify if there are any
leaks in the drip tubing laterals. If there are any leaks from
the barbed ttings or drip emitters, remove the ttings
or drip emitters and insert a goof plug to close the hole.
Reinsert the barb ttings or drip emitters nearby.
WATERING SCHEDULE
Open the faucet for 45 minutes to 1 hour every 2 to 3 days, depending on your location, weather and soil
type. Faster draining, lighter soils will need to be irrigated more frequently than heavy, soild soils with
high clay content. After a few days, check the soil and the health of the plants, and adjust the watering
schedule as needed. If you have an irrigation controller and additional time is required, adjust the irrigation
controller program with a longer watering duration and/or additional start times.
