Digi XStream-PKG Benutzerhandbuch

Digi Application Guide

Configuring XStream-PKG Serial RF Modems for Serial Bridging

March 2012 v.1 Digi International 1 of 5

1. Configure two XStream-PKG RF modems for serial bridging.

Objective: Configure two XStream-PKG Serial RF modems to build a serial bridge between two

terminals or between a terminal and a device

1.1 Software Requirements

-XCTU

-PuTTy or any Terminal application

1.2 Hardware Requirements

-XStream-PKG RS-232/485 RF Modem x 2

2. Scenario

In our example, we will connect a terminal application running on a computer on each XStream modems

and send data through the bridge.

3. Sample diagram.

Wireless

Terminal

Local

RS232

Terminal

Remote

RS232

Digi Application Guide

Configuring XStream-PKG Serial RF Modems for Serial Bridging

March 2012 v.1 Digi International 2 of 5

4. Step by step instructions

4.1 Configuring the Local XStream modem

a) Proceed to a factory reset of the modem to restore default parameters:

a. Power ON the modem

b. Set switches 1 & 2 to their ON state (up)

c. Power OFF the modem for at least one second, then on again.

b) Verify that the DIP switches settings are the following: 1 ON all OFF.

c) Connect the XStream modem to the Local Terminal computer using a RS232 Straight Thru

cable

d) Open the XCTU application and select the COM port of your computer

e) In our example we use the 19200 version of the XStream mode, so set the baud rate

accordingly and click the “Test Query”button, a new window should appear :

f) Communication with the modem is OK, click on the “Modem Configuration”tab

Digi Application Guide

Configuring XStream-PKG Serial RF Modems for Serial Bridging

March 2012 v.1 Digi International 3 of 5

g) Scroll down to Networking Set the HP (Hoping Channel) value to “1”and DT (Destination

Address) to “10”

-The Hoping Channel value is the channel on which the radio modem will

communicate. These channels are not non-interfering. Both modems must be

communicating on the same channel

-The Destination Address is the address that identifies the destination of the RF

packet. Only radio modems having matching addresses can communicate with each

others.

h) In the Modem Parameter and Firmware click the “Write”button

4.2 Configuring the Remote XStream modem

a) Proceed to a factory reset of the modem to restore default parameters:

a. Power ON the modem

b. Set switches 1 & 2 to their ON state (up)

c. Power OFF the modem for at least one second, then on again

b) Verify that the DIP switches settings are the following : 1 ON all OFF

c) Connect the XStream modem to the Local Terminal computer using a RS232 Straight

Thru cable

d) Open the XCTU application and select the COM port of your computer

e) In our example we use the 19200 version of the XStream mode, so set the baud rate

accordingly and click the “Test Query” button, a new window should appear :

Digi Application Guide

Configuring XStream-PKG Serial RF Modems for Serial Bridging

March 2012 v.1 Digi International 4 of 5

f) Communication with the modem is OK, click on the “Modem Configuration” tab

Digi Application Guide

Configuring XStream-PKG Serial RF Modems for Serial Bridging

March 2012 v.1 Digi International 5 of 5

g) Scroll down to Networking Set the HP (Hoping Channel) value to “1” and DT

(Destination Address) to “10”

-The Hoping Channel value is the channel on which the radio modem will

communicate. These channels are not non-interfering. Both modems must be

communicating on the same channel

-The Destination Address is the address that identifies the destination of the RF

packet. Only radio modems having matching addresses can communicate with each

others.

h) In the Modem Parameter and Firmware click the “Write” button

i) Close XCTU and open a terminal application such as PuTTy to the COM port where the

modems are connected on each system

j) In this test, data is sent from Local (COM1) to Remote (COM4)

Inhaltsverzeichnis

Andere Digi Modem Handbücher

Digi

Digi XBee-PRO 900HP Bedienungsanleitung

Digi

Digi XTP9B-PKC-UA Bedienungsanleitung

Digi

Digi XStream-PKG-U Bedienungsanleitung

Digi

Digi XTend-PKG Bedienungsanleitung

Digi

Digi 9XTend-PKG-U Bedienungsanleitung

Digi

Digi XBee-PRO XSC RS-232 Bedienungsanleitung

Digi

Digi Rapidport Bedienungsanleitung

Digi

Digi XB3-C-A2-UT series Bedienungsanleitung

Digi

Digi Connect WAN 3G IA Bedienungsanleitung

Digi

Digi MF710M Bedienungsanleitung

Digi

Digi M10 Technical overview and Bedienungsanleitung

Digi

Digi XBee Cellular LTE Cat 1 Bedienungsanleitung

Digi

Digi Modem Digi One IA Bedienungsanleitung

Digi

Digi XBee-PRO XM-M92-2P Series Bedienungsanleitung

Digi

Digi XBee-PRO PKG-U Bedienungsanleitung

Digi

Digi E230 Bedienungsanleitung

Digi

Digi XStream-PKG-E Bedienungsanleitung

Digi

Digi WAN 3G Bedienungsanleitung

Digi

Digi XBee-PRO XSC RF Modem Bedienungsanleitung

Digi

Digi XTend PKG-R Bedienungsanleitung

Digi

Digi XBee Bedienungsanleitung

Digi

Digi 9XTend-PKG-R RS-232 Bedienungsanleitung

Digi

Digi XStream -PKG- R Bedienungsanleitung

Digi

Digi XBee 3 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung