Digital Equipment VAX 4000 Series Bedienungsanleitung

VAX4000(BA440-Based)Systems

DSSIUpgradeInstallationGuide

Order Number: EK–VV4SY–IG. B01

Digital Equipment Corporation

Maynard, Massachusetts

First Printing, July 1993

Revised, June 1994

Digital Equipment Corporation makes no representations that the use of its products in the

manner described in this publication will not infringe on existing or future patent rights, nor do

the descriptions contained in this publication imply the granting of licenses to make, use, or sell

equipment or software in accordance with the description.

Possession, use, or copying of the software described in this publication is authorized only

pursuant to a valid written license from Digital or an authorized sublicensor.

Printed in U.S.A.

The postpaid Reader’s Comments forms at the end of this document request your critical

evaluation to assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation: DECnet, MicroVAX, VAX,

VAXcluster, VAXserver, VMS, and the DIGITAL logo.

All other trademarks and registered trademarks are the property of their respective holders.

S2643

This document was prepared using VAX DOCUMENT Version 2.1.

Contents

Preface ..................................................... v

1 Installation

1.1 System Requirements ................................. 1–1

1.2 Kit Inventory ........................................ 1–1

1.2.1 Unpacking the Kit ................................. 1–2

1.2.2 Before Installing the Kit . ........................... 1–2

1.3 Installing the Kit . . ................................... 1–2

2 Installation on a Rackmount System

2.1 System Requirements ................................. 2–1

2.2 Kit Inventory ........................................ 2–1

2.2.1 Unpacking the Kit ................................. 2–2

2.2.2 Before Installing the Kit . ........................... 2–2

2.3 Installing the Kit . . ................................... 2–2

Figures

1–1 Removing an ISE ................................. 1–4

1–2 Q–Bus Module Slots ................................ 1–6

1–3 The H3604 Console ................................ 1–8

1–4 Attaching the Bulkhead Labels ....................... 1–9

1–5 Possible DSSI Bulkhead Conﬁgurations................. 1–10

1–6 DSSI Conﬁguration Bus 2 Cabling . . ................... 1–12

1–7 DSSI Conﬁguration Bus 3 Cabling . . ................... 1–13

1–8 DSSI Conﬁguration for the Bus 2 and Bus 3 Cabling ...... 1–14

1–9 Installing the DSSI Daughter Card . ................... 1–16

1–10 Connecting the DSSI Cables to the Daughter Card ........ 1–18

2–1 Q–Bus Module Slots ................................ 2–3

iii

2–2 The H3604 Console ................................ 2–4

2–3 Attaching the Bulkhead Labels ....................... 2–5

2–4 Possible DSSI Bulkhead Conﬁgurations. ................ 2–7

2–5 DSSI Conﬁguration ‘‘A’’ Cabling (Without Q–Bus Expansion)

................................................ 2–8

2–6 DSSI Conﬁguration ‘‘B’’ Cabling (With Q–Bus Expansion)

................................................ 2–10

2–7 Installing the DSSI Daughter Card .................... 2–13

2–8 Connecting the DSSI Cables to the Daughter Card . ....... 2–15

Preface

Intended Audience

This document is intended for Digital Services personnel and licensed

self-maintenance customers.

Customer Responsibilities

It is the customer’s responsibility to perform a software backup before a Digital

Services representative arrives at the site.

Digital Services Responsibilities

The Digital Services representative should contact the customer to ensure that

the customer’s software is backed up before arriving at the site.

Document Structure

Chapter 1 contains instructions for installing the DSSI upgrade option on a

BA440–based system.

Chapter 2 contains instructions for installing the DSSI upgrade option on a

BA441–based (rackmount) system.

Related Documents

The following is a list of related documents:

Documentation Order Number

BA440/BA430 Enclosure Maintenance EK–348AB–MG

KA681/KA691/KA692 CPU System Maintenance EK–498AA–MG

VMS License Management Utility Manual AA–LA33A–TE

Installation

This chapter describes how to upgrade a VAX 4000 (BA440-based) system with

the dual DSSI bulkhead assemblies.

Caution

Modules can be damaged by static discharge if an antistatic wrist strap

is not worn or an antistatic mat is not used during handling. The wrist

strap and mat are in the antistatic kit in the Digital Services toolkit.

1.1 System Requirements

The system must have VMS software, Version 5.5–2H4, VMS 6.1, or later to

support the KFDDB–AF with the KA681, KA691, KA692, or KA694 CPU. Also,

the system must have a Rev. K01 or higher BA440 backplane (54–19354–01).

The DSSI daughter card is only supported on KA681, KA691, KA692, and

KA694 CPUs.

1.2 Kit Inventory

The DSSI upgrade kit contains the following items:

• 1 Installation document (EK–VV4SY–IG. B01)

• 1 Dual DSSI daughter card (54–20569–01)

• 2 DSSI bulkhead assemblies with cable attached (70–22860–01)

• 2 Bus 2 labels (36–26883–D4)

• 2 Bus 3 labels (36–26883–D3)

• 2 Grant cards (M9047–00)

• 2 Filler panels (74–33507–01)

• 4 DSSI terminators (12–29258–01)

Installation 1–1

• 2 cable spacers (74–49137–01)

1.2.1 Unpacking the Kit

Follow these steps when unpacking the kit.

1. Make sure there is no external damage to the shipping container, such as

dents, holes, or crushed corners.

2. Unpack the upgrade kit and check its contents against the content listing.

3. Do not unpack the DSSI daughter card at this time.

4. If any item is missing or damaged:

a. Contact the customer’s sales representative.

b. Contact the customer’s delivery agent.

1.2.2 Before Installing the Kit

Before installing the kit:

1. It is the customer’s responsibility to back up the system disk before the

Digital Services representative arrives. This is optional.

2. Run MDM diagnostics to verify system operation. This is optional.

3. Perform a VMS shutdown of the system before installing the kit.

1.3 Installing the Kit

To install the upgrade kit, do the following:

Note

The ISE ﬁgures throughout these steps show the RF-series variety.

Handle ISEs with care. Dropping or bumping the ISE can damage the

disk surface. Carry or hold the ISEs by their metal brackets to avoid

damaging the drive module.

The possible items occupying this space are as follows:

Single ISE — 1 OCP cable to remove

Dual ISE — 2 OCP cables to remove

Blank bezel — No cables to remove

1–2 Installation

1. Unlock the front door by turning the front door key switch to the bottom

position. Open both access doors simultaneously. Turn off the power switch

on the power supply.

2. To make the DSSI installation easier, it is suggested that you remove the

three ISEs (or blank bezels) starting from left to right. Refer to Figure 1–1.

3. If you choose to remove the ISEs, follow the alphabetized instructions

below. If you choose not to remove the ISEs, go to Step 4.

a. Loosen the single captive Phillips screw that secures the ISE front

panel (Figure 1–1A).

b. Separate the ISE front panel from the enclosure, being careful of the

remote front panel cable, which is connected to the ISE front panel.

c. Unplug the remote front panel cable from the module inside the ISE

front panel and set the front panel aside (Figure 1–1B).

Note

Keep track of which front panel belongs with which ISE, since the ISE

must retain its original bus node ID plug.

d. Loosen the upper and lower captive screws that hold the ISE in place

(Figure 1–1C).

e. Using the upper and lower ﬁnger cutouts on the ISE bracket, carefully

pull the ISE out of its backplane connector and slide the drive out of

the enclosure. Support the weight of the ISE as the ISE clears the

enclosure (Figure 1–1C).

Caution

Do not touch the drive module. The drive module contains sensitive

electronic circuitry.

Installation 1–3

Figure 1–1 Removing an ISE

Finger Cutouts

Remote Front

Panel Cable

Phillips Screw

Captive Screws

Remote Front

Panel Cable

MLO-004210

1–4 Installation

Andere Handbücher für VAX 4000 Series

Inhaltsverzeichnis

Andere Digital Equipment Computerhardware Handbücher

Digital Equipment

Digital Equipment PC04 Bedienungsanleitung

Digital Equipment

Digital Equipment VT 14 Bedienungsanleitung

Digital Equipment

Digital Equipment BM873 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 Series Leitfaden

Digital Equipment

Digital Equipment M7142 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 6000 Model 500 Bedienungsanleitung

Digital Equipment

Digital Equipment Digital Semiconductor 21164 Alpha... Bedienungsanleitung

Digital Equipment

Digital Equipment DECbridge 90 Bedienungsanleitung

Digital Equipment

Digital Equipment LAB-8/E Bedienungsanleitung

Digital Equipment

Digital Equipment PDP-12 Bedienungsanleitung

Digital Equipment

Digital Equipment PDP-11 Series Bedienungsanleitung

Digital Equipment

Digital Equipment 300 Series AXP Bedienungsanleitung

Digital Equipment

Digital Equipment VAX-11 /730 Bedienungsanleitung

Digital Equipment

Digital Equipment PDP16-M Bedienungsanleitung

Digital Equipment

Digital Equipment RK05 Series Bedienungsanleitung

Digital Equipment

Digital Equipment Alpha 21164PC Kurzanleitung

Digital Equipment

Digital Equipment PDP-11 Series Bedienungsanleitung

Digital Equipment

Digital Equipment PDT 11/150 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 Series Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 Series Leitfaden

Digital Equipment

Digital Equipment 300 Series AXP Leitfaden

Digital Equipment

Digital Equipment PDP-8 Bedienungsanleitung

Digital Equipment

Digital Equipment GT44 Bedienungsanleitung

Digital Equipment

Digital Equipment Venturis FX Bedienungs- und Wartungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung