Digital Monitoring Products XR100FC Bedienungsanleitung

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

Silencing an Alarm

While the re alarm horns, strobes, or sirens are sounding

use one of the following methods to silence the alarm.

1. Turn the keyswitch to enable the four

function keys. Then press the SILENCE key.

2. Enter your user code. Then press COMMAND.

Note: You may silence an alarm using both of the above

methods on the Remote Fire Command Center as well.

XR100FC/XR500FC User’s Guide i

XR100FC/XR500FC User’s Guide

Table of Contents

Section Page Section Page

Silencing an Alarm..................................................... b

Security Command User’s Guide ................................ i

for XR100FC/XR500FC Panels ................................... i

Table of Contents ....................................................... i

Emergency Evacuation Plans ................................... iii

 .......................

.....................................................

 .....................................................

 ...............................................

................................................................

Introduction .............................................................. 1

............... 1

..................................................... 1

 ...................................................................... 1

 .............................................. 2

 ............................................................ 3

.......................................................... 4

.............................. 5

 ................................. 6

 ..................................... 7

.................................................................. 8

................................................................... 8

 .............................................................. 9

 .................................................................. 10

............................................................... 11

 .................................................................. 11

 ................................................................. 12

.................................................. 13

 ................................................................... 14

 ............................................. 16

 .............................................................. 17

 .............................................................. 17

 ............................................................ 17

 ....................................................................... 17

Appendix A .............................................................. 18

.................................... 18

 ...................................................... 19

 .................................. 19

 ............................................ 20

....................................... 20

ii XR100FC/XR500FC User’s Guide

Appendix B .............................................................. 21

 ..................................................... 21

 ................................................ 22

 ................................................. 22

......................................... 23

................................................ 23

 ............................................ 24

 .......................................... 24

..................................................... 25

Appendix C .............................................................. 26

 .............................................. 26

XR100FC/XR500FC User’s Guide iii

The National Fire Protection Association recommends that you

establish an emergency evacuation plan to safeguard lives in the

event of a re or other emergency.

Draw a oorplan of your home or business

On a sheet of paper, draw the walls, windows, doors, and stairs.

Also draw any obstacles, such as large furniture or appliances, a

person may encounter while exiting the building.

Develop escape routes

Determine at least two routes the occupants in each room can take

to safely escape. One route can be the most obvious such as the

door. Another can be through a window that can be easily opened.

If the window is high off the ground, an escape ladder should be

provided. Draw arrows on the oorplan to show escape routes from

each room.

Decide where to meet

Prearrange a meeting place outside and away from where

emergency personnel are likely to be working. A neighbor’s house

or across the street in the front of the house are good locations.

Always perform a head count to make sure all occupants safely

exited. NEVER ENTER A BURNING BUILDING. If the head count shows

one or more persons missing, give this information immediately to

the authorities. Never enter a building to look for someone.

Practice your escape plans

Devising an escape plan is only the beginning, before the plan can

be effective everyone should practice the escape routes from each

room.

Second Floor

Building Front Building Back

First Floor

Fire Escape

Window Ladder

Early detection

The best way to survive a re or other emergency is to get out

early. The installation of a re alarm system, with smoke and

carbon monoxide detectors in each room, can greatly decrease

your risk of loss or injury.

Emergency Evacuation Plans

iv XR100FC/XR500FC User’s Guide

This page intentionally left blank

Introduction XR100FC/XR500FC User’s Guide 1

Introduction

A Remote Fire Command Center is also available to use with the

XR100FC/XR500FCAddressable FireAlarm Control Panel. The remote

keyboard can be placed anywhere throughout the premises.

Both keyboards have four additional function keys, to be used for

alarm silencing, resetting smoke detectors, system testing, and

performing re drills. Both keyboards require the user to turn a

keyswitch to enable the four function keys.

User Menu

The keyboards also provide access to the User Menu, which contains

all of the functions necessary to fully operate your system.

About Your Fire Alarm Control Panel

The Fire Alarm Control Panel is designed with your safety and

comfort in mind. It uses the latest in computer based technology

to create the most advanced and user-friendly re, security, and

access control system available.

The Fire Alarm Control Panel combines ease-of-use with a simple-

to-understand Fire Command Center display to offer the full range

of features requested by today’s re system owners.

You can turn portions of your protection on or off at any time by

pressing a few keys. You can add, delete, and change personal user

codes at any time or check the status of protection devices in the

system. An added feature of the Fire Alarm Control Panel is the

membrane keyboard with four additional function keys you may use

to easily perform a variety of functions.

Fire Command Center

The XR100FC/XR500FC comes with a built-in LCD display with a

20-key membrane keyboard called the Fire Command Center. The

keyboard is mounted behind an opening in the red enclosure door.

Use the keyboard to perform a variety of functions as listed in this

User’s Guide.

2 XR100FC/XR500FC User’s Guide Introduction

The Fire Command Center

Your system comes equipped with a built-in, easy-to-use Fire

Command Center that allows you to properly operate the system.

The Command Center is also available in a remote version. The

keyswitch to the left of the keyboard must be turned to the

“enable” position before you can use the four functions keys.

It is not necessary to use the keyswitch when using a user code

to perform operations. The illustration and descriptions below

highlight some features of the Fire Command Center:

Keyswitch

POWER

TROUBLE

ALARM

COMMAND

1234

5678

ABCDEF GHI JKL

MNOPQR STUVWX

ENABLE

SILENCE

RESET

TEST

DRILL

Fire Command Center

Select KeysLCD DisplayStatus LEDs

Function Keys

Data Entry Keys

Back Arrow Key

COMMAND Key

The Select keys

There are four keys under the display called the Select keys. They

allow you to choose what to do by pressing the Select key under

choices being shown in the display.

Data Entry keys

These keys allow you to enter your user code and other information

into the system.

The Back Arrow key

Use the Back Arrow key to go back through displays while operating

your system. Press the Back Arrow key to back up through the list

of User Menu functions or to make a correction by erasing the last

character you entered.

The COMMAND key

The COMMAND key allows you to advance through the displays or

User Menu or complete a data entry function.

Status LEDs

The Fire Command Center incorporates three LEDs to indicate the

system status. The three indicator lights are described below.

POWER LED

This LED remains ON steady when both AC and battery input are

good. The LED turns OFF when AC input is low. The LED ashes at

half-second intervals when battery input is low.

TROUBLE LED

This LED turns ON when any trouble displays in the status list, such

as AC, battery, phone line, transmit, ground fault, NAC, or any zone

trouble. This light is OFF when no trouble displays in the status

list.

ALARM LED

The ALARM LED is ON when any alarm currently displays in the

status list. This LED is OFF when no alarm currently displays in

the status list.

Introduction XR100FC/XR500FC User’s Guide 3

Asterisks in Burglary Area Armed Displays

Asterisks display next to a programming option that is already

selected. As shown in the example, options chosen to display

the current programming selection have an asterisk next to the

number. Those that are not selected simply display the number.

In the example, Burglary Areas 3, 8, 9, 15, 19, 23, 25, and 31 are

not selected. In both examples the numbers with asterisks are

selected.

Burglary Areas

*1 *2 3 *4 *17 *18 19 *20

*5 *6 *7 8 *21 *22 23 *24

9 *10 *11 *12 25 *26 *27 *28

*13 *14 15 *16 *29 *30 31 *32

To select or deselect a number, simply enter the number using the

digit keys on the keypad. This same scheme is used when viewing

the panel armed status and other programming and operational

functions. Remember to press the COMMAND key to display the

rest of the device or area numbers.

Using the Keypad

Multi-lingual Display Option

Your system may be programmed to display the User Menu and

Status Display text in multiple languages. When the COMMAND

key is pressed, the option to choose the language displays. The

language chosen continues to display at this keypad until another

language is chosen.

Keypad Displays Current Programming

Most User Menu options displayed at the keypad show the currently

selected option in the panel memory. These options are either

shown as a number, a blank, or a NO or YES. To change a number

press any top row Select key. The current option is replaced with a

dash. Press the number(s) on the keypad you want to enter as the

new number for that option.

It is not necessary to enter numbers with leading zeros. The panel

automatically right justies when you press the COMMAND key.

To change an option that requires a NO or YES response, press the

top row Select key under the response not selected.

For example, if the current option is YES and you want to change it

to NO, press the third top row Select key. The display changes to

NO. Press the COMMAND key to go to the next option.

Multiple Displays

For many User Menu options on burglary keypads of combination

burglary and re systems, such as Access Areas, there are several

displays containing lists. For example, in Access Areas, areas 1

through 32 display on four separate displays. First, areas 1 through

8 display. Press the COMMAND key to display areas 9 through 16.

Press the COMMAND key again to display areas 17 through 25. Press

the COMMAND key one more time to display areas 26 through 32.

Note: Only areas pre-programmed at installation can display.

4 XR100FC/XR500FC User’s Guide Introduction

User Options

The User Options allow you to make adjustments to your keypad to

best t your environment and needs.

To access the User Options portion of the keypad, press and hold

the Back Arrow and COMMAND keys for two seconds. The keypad

display changes to SET BRIGHTNESS. Press the COMMAND key to

display the next option or the Back Arrow key to exit.

Backlighting Brightness

Sets the keypad LCD, and AC LED backlighting brightness level.

At the SET BRIGHTNESS display, use the left Select key to lower

the keypad brightness. Use the right Select key to increase the

brightness.

Note: If the brightness level is lowered, it temporarily reverts back

to maximum intensity whenever a key is pressed.

Internal Speaker Tone

Sets the keypad internal speaker tone. At the SET TONE display,

use the top left Select key to make the tone lower. Use the right

Select key to make the tone higher.

Volume level

Sets the keypad internal speaker volume level for key presses and

prewarn conditions. During alarm, trouble, and prewarn conditions,

the volume is always at maximum level. At SET VOLUME LEVEL,

use the left Select key to lower the keypad volume. Use the right

Select key to raise the volume.

Model Number

The keypad model number, rmware version, and date display, but

cannot be changed.

Four Function Keys

The Fire Command Center is designed with four additional keys on

the left side of the keypad. After turning the keyswitch, you can

quickly perform vital functions using these four keys.

SILENCE Key

Pressing the SILENCE key silences the alarm bells.

RESET Key

Pressing the RESET key performs a sensor reset and silence the

alarm bells.

TEST Key

Pressing the TEST key performs a system test.

DRILL Key

Pressing the DRILL key displays a prompt “SURE? YES NO”. Press

YES to begin the re drill. Press NO to return to the status list.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digital Monitoring Products Bedienfeld Handbücher

Digital Monitoring Products

Digital Monitoring Products XF6 Series Installationsanleitung

Digital Monitoring Products

Digital Monitoring Products 1912XR Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products COMMAND PROCESSOR XR500 Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products 1912XR Betriebsanleitung

Digital Monitoring Products

Digital Monitoring Products XR500 Series Betriebsanleitung

Digital Monitoring Products

Digital Monitoring Products XTLplus Series Installationsanleitung

Digital Monitoring Products

Digital Monitoring Products XR2500F Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XTL Series Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XF6 Series Installations- und Betriebsanleitung

Digital Monitoring Products

Digital Monitoring Products XTLplus 9000 Series Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XTL Series Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XT Series Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150FC Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung