Digital Monitoring Products 691 Installationsanleitung

INSTALLATION AND PROGRAMMING GUIDE

691 Keypad

ABC(

DEF)

GHI!

JKL?

MNO/

YZ_’

-.*#

CMD

PQR&

STU$

VWX,

About the 691 Keypad ............................... 1

2-Button Panic Keys............................................ 1

Internal Speaker.................................................... 1

External Sounder.................................................. 1

Install the Keypad.......................................2

Prepare the Base ................................................. 2

Mount and Wire the Keypad........................... 2

User Options ...............................................4

Type in the Keypad ....................................6

Entering Alpha Characters .............................. 6

Entering Non-Alphanumeric Characters.... 6

TABLE OF CONTENTS

Installer Options Menu...............................7

Accessing Installer Options............................. 7

Keypad Options ................................................... 7

Keypad Diagnostics............................................ 9

Exit the Installer Options.................................. 9

Additional Power Supply ........................ 10

Keypad Bus Wiring Speciﬁcations.......... 11

Product Speciﬁcations ............................ 12

LCD Display

Select Keys

Number Keys

Keypad Base

Keypad Cover

Tamper-Proof Screw

Figure 1: 691 Keypad

Digital Monitoring Products, Inc. | 691 Keypad Installation and Programming Guide 1

The Model 691 is a weatherproof outdoor keypad mounted on an aluminum black powder coated

box.

ABOUT THE 691 KEYPAD

2-Button Panic Keys

Enable the Panic key function in the keypad

user menu. See Arm Panic Keys.

The user must press and hold the two Select

keys for two seconds until the keypad emits a

beep. Then the panel sends the following zone

alarm reports to the central station:

• Panic (left two Select keys)

• Emergency—non-medical (center two

Select keys)

• Fire (right two Select keys)

Internal Speaker

The keypad emits standard tones for key

presses, entry delay, and system alerts. The

keypad also provides burglary, ﬁre, zone

monitor, and prewarn cadences. The keypad

provides an alternate prewarn with alarm

cadence that occurs when the status list

displays a zone alarm.

External Sounder

The keypad provides a switched ground for an

external sounder that turns on with the keypad

on-board sounder. The sounder activates

when the keypad switches to ground. The

sounder silences when the keypad restores.

Power-limited, maximum current of switched

ground is 50mA@30VDC.

1. Connect the negative side of an

external sounder to the violet wire on

the keypad wiring harness.

2. Connect the positive side of the

sounder to the positive side of a

power source rated at 30 VDC or less.

3. Ground the negative side of the power

source to the black wire of the keypad

bus.

2 691 Keypad Installation and Programming Guide | Digital Monitoring Products, Inc.

INSTALL THE KEYPAD

Prepare the Base

The keypad housing is made up of two parts: the base and the keypad cover, which

contains the circuit board and keyboard components.

1. Determine the placement of the wire harness opening based on the mounting location.

2. Drill a hole 1/4” in diameter through the back of the base for the wiring harness.

Mount and Wire the Keypad

1. Feed the panel keypad bus wiring through the opening in the back of the base.

Mount the base in the desired location using the mounting holes. Seal the wiring

opening with a weatherproof sealant. See Figure 2.

2. Connect the panel keypad bus wiring to the keypad harness. Observe wire colors

when connecting and do not use shielded wire.

Figure 3 shows wiring harness assignments. Observe wire colors when connecting

the red, yellow, green, and black wires to the keypad bus. The violet wire can be

used for an external sounder. See External Sounder.

3. Plug the 5-wire harness connector onto the keypad connection.

Note: The keypad LCD display contrast level can be adjusted by inserting a

screwdriver into the contrast hole on the upper left corner of the keypad PCB. See

Figure 4. Turn the screwdriver to the left to lower the contrast and to the right to

raise the contrast.

4. Place the front cover onto the base and line up the screw holes to the base. Secure

the cover to the base with the included six tamper-proof screws using the tamper

bit. See Figure 3.

Digital Monitoring Products, Inc. | 691 Keypad Installation and Programming Guide 3

Mounting Hole

Screw Holes for Front Cover

Gasket

Figure 3: Inside Base View

CONTRAST

Contrast Setting

Keypad Harness Connection

Figure 4: Keypad PCB

Violet – Sounder

Black – Ground

Green

– Receive Data

Yellow – Send Data

Red – Keypad Power

Figure 2: Wiring Harness

4 691 Keypad Installation and Programming Guide | Digital Monitoring Products, Inc.

USER OPTIONS

All keypads provide three keypad adjustments the end-user can make through a User Options

Menu. The user can also view the keypad model number and address.

On all keypads press and hold the Back Arrow (←) and Command (CMD) keys for two seconds

to access User Options. The keypad display changes to SET BRIGHTNESS. Use the CMD key to

display the next Option or press the Back Arrow to exit.

Backlighting Brightness

Set the keypad LCD Display brightness level. Use the left Select

key to lower the brightness and the right Select key to raise the

brightness. If the brightness level is lowered, it reverts to maximum

intensity whenever a key is pressed. If no keys are pressed, and

the speaker has not sounded for 30 seconds, the user-selected

brightness level restores.

Internal Speaker Tone

Set the keypad internal speaker tone. At the SET TONE display,

use the left Select key to lower the tone and the right Select key to

raise the tone.

SET BRIGHTNESS

< ▐▐▐▐▐▐ >

SET TONE

< ▐▐▐▐▐▐▐ >

Digital Monitoring Products, Inc. | 691 Keypad Installation and Programming Guide 5

Internal Volume Level

Set the keypad internal speaker volume for key presses and entry

delay tone conditions. During alarm and trouble conditions, the

volume is always at maximum level. Use the left Select key to

decrease the volume and the right Select key to increase the

volume.

Model Number

The LCD displays the keypad model number and ﬁrmware version

and date. The user cannot change this information.

Keypad Address

The LCD displays the current keypad address. The user cannot

change the keypad address.

SET VOLUME LEVEL

< ▐▐▐▐▐▐▐ >

MODEL NUMBER

691 V100 041811

KEYPAD ADDRESS

6 691 Keypad Installation and Programming Guide | Digital Monitoring Products, Inc.

TYPE IN THE KEYPAD

Entering Alpha Characters

To enter an alpha character, press the key that

has the desired letter written below it. The

keypad display shows the number on that key.

To change the number to a letter, press the

top row Select key that corresponds to the

letter location under the key. For example, if

you press key number 1, the letters for that key

are A, B, and C. Press the ﬁrst Select key for

A, the second Select key for B, the third Select

key for C, and fourth Select key for special

characters. See Figure 5.

First Letter

Second Letter Third Letter

Special Character

(CBA

Figure 5: Alpha Characters

Entering Non-Alphanumeric

Characters

Each key also has a special, non-alpha

character. These characters are not shown on

the keypad. Enter a space by pressing 9 then

the third Select key.

The following non-alpha characters are

available: ( ) ! ? / & $ ‚ (space)’ starting with

the left bracket on the 1 digit key to the blank

space and apostrophe on the 9 digit key. Use

the 0 digit key to enter - . * # (dash, period,

asterisk, or number sign). See Figure 6.

ABC(

DEF)

GHI!

JKL?

MNO/

YZ_’

-.*#

CMD

PQR&

STU$

VWX,

Figure 6: Non-Alpha Characters

Inhaltsverzeichnis

Andere Digital Monitoring Products Tastenfeld Handbücher

Digital Monitoring Products

Digital Monitoring Products XR5 Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products 9000 series Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR5 Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products GRAPHIC TOUCHSCREEN KEYPAD Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products Security Command 690 Montageanleitung

Digital Monitoring Products

Digital Monitoring Products Thinline 7060 Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products Thinline 7070 Montageanleitung

Digital Monitoring Products

Digital Monitoring Products 9800 SERIES Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung

Bosch

Bosch D1260 Series Bedienungsanleitung

Elmes Electronic

Elmes Electronic KB1 Bedienungsanleitung

Clare Controls

Clare Controls ClareOne CLR-C1-PNC Montageanleitung