Digital Projection Vision 30 Series Bedienungsanleitung
Vision 30 Series
Communication Protocol
www.digitalprojection.com
Revision 1.0
03/28/2008
Table of Contents
Table of Contents ...............................................................................................................................................................................1
Setting up LAN communication .........................................................................................................................................................2
Connecting to the projector ...............................................................................................................................................................2
Setting up RS232 communication .....................................................................................................................................................5
Connect to the projector ...............................................................................................................................................................5
RS232 Communication parameters ..............................................................................................................................................5
Communication Protocol....................................................................................................................................................................6
Overview........................................................................................................................................................................................6
Message body ...............................................................................................................................................................................6
Mnemonic......................................................................................................................................................................................6
Modiers........................................................................................................................................................................................7
Acknowledge/Response................................................................................................................................................................7
Examples .......................................................................................................................................................................................8
ASCII commands .............................................................................................................................................................................10
Value tables ......................................................................................................................................................................................10
Setting up LAN communication
The projector is shipped with a set of default settings, these are as follows:
Description Value
DHCP On
IP address 0.0.0.0
Subnet mask 0.0.0.0
Default gateway 0.0.0.0
TCP/UDP port 1025
Username admin
Password admin
Before you connect the projector to your LAN make sure that the IP settings are set correct according to your LAN conguration.
IP settings can be changed from menu system or from the projector webpage. It can be set automatically by using DHCP (Dynamic
Host Conguration Protocol) or manually by disabling DHCP and set IP address, Subnet mask and Gateway.
Use of DHCP requires a DHCP server in the network.
When enabling DHCP please allow up to a minute for the projector to receive IP settings from the DHCP server. The IP address will be
updated and shown in the menu system.
Connecting to the projector
You have two options regarding how to make the physical connection to the projector. You can either use a crossover twisted pair (TP)
cable directly from the computer to the projector, or two straight-through TP cables with a HUB or a switch between them.
When the projector is set up with proper IP settings, you should be able to control it.
To verify the communication you can connect to the projector webpage. This is done by starting up an internet browser, like Internet
Explorer, Opera, Firefox or similar. Then type the projectors IP address (found in the projector network menu) in the address bar.
You will then see a login screen, see Figure 1.
Figure 1 : Login
Type in the projectors default login name (admin) and password (admin), both are case sensitive. If both are correct, you will se a
conguration website, see Figure 2.
Figure 2 : Web page
On this page you can setup the projectors IP address, subnet mask, default gateway, projector port (TCP/UDP) and password. This
page also displays the current version of network rmware the projector is running.
Setting up RS232 communication
Connect to the projector
Connect the projector and host using a standard serial cable with 9-pin female to the host, and 9-pin male to the projector. Pin 2
connects to pin 2, pin 3 connects to pin 3 and pin 5 connects to pin 5.
RS232 Communication parameters
Table 1 shows supported rs232 settings:
Parameter Data
Baud rate 4800, 9600, 19200
Parity N
Databits 8
Stopbits 1
Flowcontrol None
Table 1: RS232 parameters
Baud rate is congurable from the projector’s menu system. Default baud rate is 19200.
Communication Protocol
This section describes how to use the communication protocol to control projectors remotely.
When the projects are connected to either RS232 or LAN you can control the projectors through this ASCII based protocol.
Note: Some commands will generate OSD feedback. This can be turned off from the projector’s menu system or by setting
“OSDC” to value 0 (OSD off) or value 1 (OSD show only warnings).
Overview
The protocol has the following denition:
HEADER SEPARATOR ADDRESS SEPARATOR MESSAGE BODY TERMINATOR
1 byte 1 byte 1 -3 bytes 1 byte N bytes 1 byte
Field Description Comment
Header ASCII character ‘:’ Required
Separator ASCII character ‘space’ Optional
Address 1 – 3 bytes address Optional
Terminator CR carriage return (0x0D) Required
Message body
The message body structure is as follows:
MNEMONIC SEPARATOR] MODIFIER SEPARATOR VALUES
1 byte 1 byte 1 -3 bytes 1 byte N bytes
Field Description Comment
Mnemonic 4 bytes key identier, not case sensitive Required
Modifer Single char symbol Optional
VALUES 1 – 3 bytes address Optional
Separator ASCII character ‘space’ Optional
Mnemonic
The Mnemonic is 4 bytes key identier, know as the ASCII command.
Example: POWR, SABS, IVGA
Modiers
R Relative change. Value given will be reletive to the existing value.
Example: :BRIG R10 will increase brightness with 10 steps
ARequest acknowledges. This modier is the only
used to read back the result of the command.
Default all commands send acknowledges so this will not be
necessary.
?Get current value
?M Get maximum value
?N Get minimum value
?D Get default value
?S Get default step value
Acknowledge/Response
Acknowledge is optional and ON by default. Auto acknowledge can be turned on and off with ECHO commad. It can also be activated
on a per command basis using modier A.
ACK ADDRESS SEP COMMAND SEP VALUE TERM
1 byte 3 bytes 1 byte 4 bytes 1 byte 6 bytes 1 byte
Field Description Comment
ACK ASCII character ‘%’ Always
SEP ASCII space Always
VALUE 6 bytes return value Always
TERM Termination char 0x0D (CR) Always
Most commands value returns the actual value of the requested command. If the requested command is not valid the response may
include an error message.
Code Error message Description
!00001 Access denied Current access level is too low
!00002 Not available Command currently not available.
Ex. contrast is not available when the
projector is searching
!00003 Not implemented Command to implemented
!00004 Value out of range Value out of range
Some commands could return a value that is more than 6 characters, for instance strings.
Code Extended info Description
e00001 Extended info, string A description string follows
Example:
> :seri ?
> %001 SERI e00001 07010001
Examples
The protocol accepts one single SPACE between elds, or no SPACE between elds.
‘CR’ ASCII value carriage return, hex value 0x0D.
SET-commands
SET POWER ON
: P O W R 1 ‘CR’
:POWR1’CR’
ACKNOWLEDGE POWER ON
% 0 0 1 P O W R 0 0 0 0 0 1 ‘CR’
%001 POWR 000001’CR’
SET BRIGHTNESS TO 60
: B R I G6 0 ‘CR’
:BRIG 60’CR’
ACKNOWLEDGE BRIGHTNESS
% 0 0 1 B R I G000060‘CR’
%001 BRIG 000060’CR’
INCREMENT CONTRAST
: C N T R R 1 ‘CR’
:CNTR R1’CR’
ACKNOWLEDGE INCREMENT CONTRAST
% 0 0 1 C N T R 0 0 0 0 6 1 ‘CR’
%001 CNTR 000061’CR’
DECREMENT CONTRAST with 2 steps
: C N T R R - 2 ‘CR’
:CNTR R-2’CR’
ACKNOWLEDGE INCREMENT CONTRAST
% 0 0 1 C N T R 0 0 0 0 5 9 ‘CR’
%001 CNTR 000059’CR’
GET-commands
GET current value CONTRAST
: C N T R ? ‘CR’
:CNTR?’CR’
ACKNOWLEDGE CONTRAST GET
% 0 0 1 C N T R 0 0 0 0 5 9 ‘CR’
%001 CNTR 000059’CR’
GET minimun value BRIGHTNESS
: B R I G? N ‘CR’
:BRIG ?N’CR’
ACKNOWLEDGE BRIGHTNESS GET MIN
% 0 0 1 B R I G000000‘CR’
%001 CNTR 000000’CR’
ASCII protocol
Showing all properties for available commands
Command Description Platforms* Operations
supported Comments
POWR Power IVision 30, IVision 20,
DVision 30
Get, Set
POST Power state IVision 30, IVision 20,
DVision 30
Get See value table POST
Soure selection
IABS Set source abs values IVision 30, IVision 20,
DVision 30
Get, Set See value table IABS
IVGA Select VGA IVision 30, IVision 20,
DVision 30
Get, Set
ISVI Select S-video IVision 30, IVision 20,
DVision 30
Get, Set
IDVI Select DVI IVision 30, IVision 20,
DVision 30
Get, Set
ICVI Select Composite video IVision 30, IVision 20,
DVision 30
Get, Set
IYPP Select Component YPbPr IVision 30, IVision 20,
DVision 30
Get, Set
IRGS Select RGB video IVision 30, IVision 20,
DVision 30
Get, Set
IHDM Select HDMI IVision 30, IVision 20,
DVision 30
Get, Set
IBNC Select BNC DVision 30 Get, Set
ISTS Signal Status IVision 30, IVision 20,
DVision 30
Get 0 - searching 1 - locked to source
Picture
BRIG Brightness IVision 30, IVision 20,
DVision 30
Get, Set
CNTR Contrast IVision 30, IVision 20,
DVision 30
Get, Set
CSAT Color IVision 30, IVision 20,
DVision 30
Get, Set
VHUE Hue Video IVision 30, IVision 20,
DVision 30
Get, Set
SHRP Sharpness IVision 30, IVision 20,
DVision 30
Get, Set
PRST Picture Reset IVision 30, IVision 20,
DVision 30
Get, Set
AUTO Auto IVision 30, IVision 20,
DVision 30
Set
PMUT Picture Mute IVision 30, IVision 20,
DVision 30
Get, Set
FRZE Freeze Image IVision 30, IVision 20,
DVision 30
Get, Set
SABS Set Scaling abs value IVision 30, IVision 20,
DVision 30
Get, Set See value table SABS
S1T1 Select Scaling 1:1 IVision 30, IVision 20,
DVision 30
Get, Set
S169 Select Scaling 16:9 IVision 30, IVision 20,
DVision 30
Get, Set
SS43 Select Scaling 4:3 IVision 30, IVision 20,
DVision 30
Get, Set
SFLA Select Scaling FillAll IVision 30, IVision 20,
DVision 30
Get, Set
*Supported commands for the various product platforms are marked IVision 30, IVision 20, and DVision 30.
SFAR Select Scaling FillAspectRatio IVision 30, IVision 20,
DVision 30
Get, Set
SLET Select Scaling Letterbox to 16:9 IVision 30, IVision 20,
DVision 30
Get, Set
SLST Select Scaling Letterbox St to 16:9 IVision 30, IVision 20,
DVision 30
Get, Set
GAFI Select Gamma Film IVision 30, IVision 20,
DVision 30
Get, Set
GAVI Select Gamma Video IVision 30, IVision 20,
DVision 30
Get, Set
GACO Select Gamma Computer IVision 30, IVision 20,
DVision 30
Get, Set
GABS Set Gamma abs value IVision 30, IVision 20,
DVision 30
Get, Set
Picture->ColorMax
BCMO BrilliantColor Mode IVision 30 Get, Set See value table BCMO
BCPR BrilliantColor Preset IVision 30, IVision 20,
DVision 30
Get, Set See value table BCPR
PRES BrilliantColor Preset Settings IVision 30 Get, Set See value table PRES
WPEK BrilliantColor Boost IVision 30, IVision 20,
DVision 30
Get, Set
CMXV Color Management X-Coordinate IVision 30, IVision 20,
DVision 30
Get, Set
CMYV Color Management Y-Coordinate IVision 30, IVision 20,
DVision 30
Get, Set
CMNA Color Management Mode Not Corrected IVision 30, IVision 20,
DVision 30
Get, Set
CMTE Color Management Mode Color Temeperature IVision 30, IVision 20,
DVision 30
Get, Set
Command Description Platforms Operations
supported Comments
CCXY Color Management Mode Custom Coordinates IVision 30, IVision 20,
DVision 30
Get, Set
CMHS Color Management Mode HSG IVision 30 Get, Set
CMPR Color Management Mode presets IVision 30
RD65 Reset to D65 IVision 30, IVision 20,
DVision 30
Set
DSCR Desired Coords Mode IVision 30, IVision 20,
DVision 30
Get, Set See value table DSCR
BAGA Balance Gains Enable IVision 30, IVision 20,
DVision 30
Get, Set
DSRX Desired Red X IVision 30, IVision 20,
DVision 30
Get, Set
DSRY Desired Red Y IVision 30, IVision 20,
DVision 30
Get, Set
DSRG Desired Red Gain IVision 30, IVision 20,
DVision 30
Get, Set
DSGX Desired Green X IVision 30, IVision 20,
DVision 30
Get, Set
DSGY Desired Green Y IVision 30, IVision 20,
DVision 30
Get, Set
DSGG Desired Green Gain IVision 30, IVision 20,
DVision 30
Get, Set
DSBX Desired Blue X IVision 30, IVision 20,
DVision 30
Get, Set
DSBY Desired Blue Y IVision 30, IVision 20,
DVision 30
Get, Set
DSBG Desired Blue Gain IVision 30, IVision 20,
DVision 30
Get, Set
DSCX Desired Cyan X IVision 30, IVision 20,
DVision 30
Get, Set
DSCY Desired Cyan Y IVision 30, IVision 20,
DVision 30
Get, Set
DSCG Desired Cyan Gain IVision 30, IVision 20,
DVision 30
Get, Set
DSMX Desired Magenta X IVision 30, IVision 20,
DVision 30
Get, Set
DSMY Desired Magenta Y IVision 30, IVision 20,
DVision 30
Get, Set
DSMG Desired Magenta Gain IVision 30, IVision 20,
DVision 30
Get, Set
DSYX Desired Yellow X IVision 30, IVision 20,
DVision 30
Get, Set
DSYY Desired Yellow Y IVision 30, IVision 20,
DVision 30
Get, Set
DSYG Desired Yellow Gain IVision 30, IVision 20,
DVision 30
Get, Set
DSWG Desired White Gain IVision 30, IVision 20,
DVision 30
Get, Set
DFRX Factory Desired Red X IVision 30, IVision 20,
DVision 30
Get, Set
DFRY Factory Desired Red Y IVision 30, IVision 20,
DVision 30
Get, Set
DFRG Factory Desired Red Gain IVision 30, IVision 20,
DVision 30
Get, Set
DFGX Factory Desired Green X IVision 30, IVision 20,
DVision 30
Get, Set
DFGY Factory Desired Green Y IVision 30, IVision 20,
DVision 30
Get, Set
DFGG Factory Desired Green Gain IVision 30, IVision 20,
DVision 30
Get, Set
DFBX Factory Desired Blue X IVision 30, IVision 20,
DVision 30
Get, Set
DFBY Factory Desired Blue Y IVision 30, IVision 20,
DVision 30
Get, Set
DFBG Factory Desired Blue Gain IVision 30, IVision 20,
DVision 30
Get, Set
DFCX Factory Desired Cyan X IVision 30, IVision 20,
DVision 30
Get, Set
DFCY Factory Desired Cyan Y IVision 30, IVision 20,
DVision 30
Get, Set
DFCG Factory Desired Cyan Gain IVision 30, IVision 20,
DVision 30
Get, Set
DFMX Factory Desired Magenta X IVision 30, IVision 20,
DVision 30
Get, Set
DFMY Factory Desired Magenta Y IVision 30, IVision 20,
DVision 30
Get, Set
DFMG Factory Desired Magenta Gain IVision 30, IVision 20,
DVision 30
Get, Set
DFYX Factory Desired Yellow X IVision 30, IVision 20,
DVision 30
Get, Set
DFYY Factory Desired Yellow Y IVision 30, IVision 20,
DVision 30
Get, Set
DFYG Factory Desired Yellow Gain IVision 30, IVision 20,
DVision 30
Get, Set
Inhaltsverzeichnis
Andere Digital Projection Projektor Handbücher
Digital Projection
Digital Projection Titan 1080p-500 Bedienungsanleitung
Digital Projection
Digital Projection 7000 Series Bedienungsanleitung
Digital Projection
Digital Projection 40HD-T Bedienungsanleitung
Digital Projection
Digital Projection M-Vision 930 3D Series Bedienungsanleitung
Digital Projection
Digital Projection dVision Scope 1080p Bedienungsanleitung
Digital Projection
Digital Projection MERCURY 5000HD Bedienungsanleitung
Digital Projection
Digital Projection LIGHTNING 30isx+ Betriebsanleitung
Digital Projection
Digital Projection HIGHlite 6000 Bedienungsanleitung
Digital Projection
Digital Projection LIGHTNING 45-1080p 3D Bedienungsanleitung
Digital Projection
Digital Projection TITAN sx+600 Bedienungsanleitung
Digital Projection
Digital Projection HIGHlite Laser II 3D Series Betriebsanleitung
Digital Projection
Digital Projection TITAN HD-600 Bedienungsanleitung
Digital Projection
Digital Projection TITAN sx+-330-3D L or P Bedienungsanleitung
Digital Projection
Digital Projection THUNDER 10000sx Bedienungsanleitung
Digital Projection
Digital Projection HIGHlite 660 3D Series Betriebsanleitung
Digital Projection
Digital Projection M-Vision 1080p-260 series Bedienungsanleitung
Digital Projection
Digital Projection iVision Bedienungsanleitung
Digital Projection
Digital Projection INSIGHT 4K Quad Series Bedienungsanleitung
Digital Projection
Digital Projection TITAN SX+ 500 Bedienungsanleitung
Digital Projection
Digital Projection FUSION Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
