Digital Watchdog DW-ESTS Bedienungsanleitung

4. Right-click on ‘Ethernet’ and select ‘Properties’ from the drop-down options.

5. Double-click on ‘Internet Protocol version 4 (TCP/IPv4)’ in the Properties window.

6. Enter the IP and subnet mask as shown below and click the OK button.

7. Click the OK button in the Ethernet Properties window to close the window.

Quick Start Guide

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/support-download/

2. Search for your product by entering the part number in the “Search by Product”

search bar. Results for applicable part numbers will populate automatically based

on the part number you enter.

3. Click “Search”. All supporting materials, including manuals, Quick Start Guides

(QSG), software and ﬁrmware will appear in the results.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours: 9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for the initial setup. It is recommended

that the user read the entire instruction manual for complete and proper installation and usage.

DW-ESTS Complete Kit

DW-ESTCAM Camera Only

DW-ESTBLKB Blackbody Only

Quick Start Guide

Follow the diagram below to connect the

camera to all applicable external devices.

1. Install the Elevated Skin Temperature System software, available on Digital Watchdog’s website.

a. Go to http://www.digital-watchdog.com

b. Search for ‘EST software’ on the search bar at the top of the page.

c. The latest software will appear in the search results. Click on the link to download the ﬁle to

your computer and run the installation ﬁle.

2. When the camera connects directly to the PC, the following is assigned to the camera by default:

• Camera IP address: 169.254.100.100.

• Subnet mask: 255.255.0.0.

3. Open the execution window on the monitoring PC by pressing the “Window ( )+R” buttons.

Enter ‘ncpa.cpl’ and press ‘enter’.

STEP 1 – CAMERA CONNECTION

STEP 2 – SOFTWARE INSTALLATION

NOTE: The software is available for Windows® 10 OS only.

WHAT’S IN THE BOX

DW-ESTS Camera, Blackbody, LED strobe, 2x tripods, 2x power supplies, LAN cable, quick setup guide.

DW-ESTCAM Camera, LED strobe, power supply, quick setup guide

DW-ESTBLKB Blackbody, power supply, quick setup guide

NOTE: Make sure the PC’s IP address is not overlapping with the camera’s IP address. The PC’s

IP setting ranges arbitrarily from 169.254.100.1 ~ 169.254.100.254. Make sure to set the

subnet mask to 255.255.0.0.

NOTE: Install the Blackbody facing the camera, 9.8~14.7ft

from the camera (10ft is recommended) and

connect it to an adequate power supply.

Quick Start Guide

Speciﬁcations and pricing are subject to change without notice.

STEP 3 – SETTING UP YOUR SCREENING STATION

Rev: 10/20

NOTE: This product is not designed by DW for the speciﬁc intention of human fever detection nor the

diagnosis, mitigation, or prevention of disease or health conditions.

1. Install the camera facing away from the entrance or windows.

2. Place the camera 6.5~16.4ft from the monitoring path (10ft is recommended).

3. Place the camera at a 20° angle from the monitoring path.

4. Make sure people are walking into the camera’s FoV rather than straight towards the camera.

5. Place the Blackbody across from the camera, positioned in the corner of the camera’s FoV.

6. The Blackbody should be 9.8~14.7ft from the camera (10ft is recommended). 5ft is the

recommended height.

7. Setup a monitoring station next to the camera with a monitoring PC and personnel. See STEP 1.

8. One person in the FoV at a time.

9. Recommended room temperature is 68° to 86°F (20° to 30°C), under 80% humidity.

NOTES AND CONSIDERATIONS:

1. Allow the camera and Blackbody up to 5 minutes from power-up to calibrate properly.

2. When installing a camera-only solution, allow up to 30 minutes to calibrate.

3. When powering up the E.S.T. monitoring software, keep the camera’s FoV clear of people and

moving objects for 10 seconds.

FALSEFALSE

4. Do not install the camera or Blackbody under an air conditioner duct.

5. Strong ﬂuorescent lights may impact temperature readings.

6. Sunlight from windows and large glass doors in the camera’s FoV may cause false readings.

7. Consider that any extensive physical activity performed before screening may impact the

facial skin temperature captured by the camera.

8. IMPORTANT! Always follow elevated temperature readings with additional screening such

as a medical thermometer and wellness questionnaire.

Dieses Handbuch passt für folgende Modelle

Andere Digital Watchdog Wärmebildkamera Handbücher

Digital Watchdog

Digital Watchdog E.S.T. DW-ESTS Bedienungsanleitung

Beliebte Wärmebildkamera Handbücher anderer Marken

Hikmicro

Hikmicro B20 Bedienungsanleitung

FLIR

FLIR E-EST Series Bedienungsanleitung

FLIR

FLIR M-Series Bedienungsanleitung

BST

BST BT-72 Bedienungsanleitung

FLIR

FLIR G300 pt Series Bedienungsanleitung

CBC

CBC EN7-S02T Bedienungsanleitung

Satir

Satir YRH600 Bedienungsanleitung

TESTO

TESTO 882 Bedienungsanleitung

TECPEL

TECPEL TIG-320 Bedienungsanleitung

SKF

SKF TKTI 21 Bedienungsanleitung

TESTO

TESTO 885 Bedienungsanleitung

InfiRay

InfiRay AT300 Series Bedienungsanleitung

InfiRay

InfiRay AT Series Bedienungsanleitung

FLIR

FLIR X6530sc Series Bedienungsanleitung

Videotec

Videotec MAXIMUS MVXT Bedienungsanleitung

Guide Sensmart

Guide Sensmart D384M Bedienungsanleitung

NBN

NBN FLIR A6 Series Bedienungsanleitung

WORKSWELL

WORKSWELL SAFETIS Bedienungsanleitung