DigitaLinx IPEX5001-D Bedienungsanleitung
11675 Ridgeline Dr.
Colorado Springs, CO 80921
Rev 191115 Toll-Free: 800-530-8998
Fax: 719-260-0075
supportlibav@libav.com
IPEX5000 Series Install Guide
This guide is for basic installaon only.
For complete Digitalinx IP Deployment Guide go to www.libav.com or use a
QR reader to access the manual via QR code below.
Scan QR Code with your Smart-phone or Tablet
IPEX5000 Series Quick Install Guide
3
1. Read these instrucons – All the safety and operang instrucons should be read before this product is operated.
2. Keep these instrucons – The safety and operang instrucons should be retained for future reference.
3. Heed all warnings – All warnings on the appliance and in the operang instrucons should be adhered to.
4. Follow all instrucons – All operang and use instrucons should be followed.
5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet
basement or near a swimming pool, and the like.
6. Clean only with a dry cloth.
7. Do not block any venlaon openings. Install in accordance with the manufacturer’s instrucons.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
9. Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one wider than the other.
The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and at the
point where it exits from the apparatus.
11. Only use aachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the
apparatus. When a cart or rack is used, use cauon when moving the cart/ apparatus combinaon to avoid injury
from p-over.
13. Unplug the apparatus during lighng storms or when unused for long periods of me.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any
way, such as; the power-supply cord or plug is damaged, liquid has been split or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. CAUTION: Servicing instrucons are for use by qualied service personnel only. To reduce the risk of electric shock, do
not perform any servicing other than that contained in the operang instrucons unless you are qualied to do so.
16. Do not install this equipment in a conned or built-in space such as a book case or similar unit. The equipment must
remain in well venlaon condions. Venlaon should not be impeded by covering the venlaon openings with items
such as newspaper, table-cloths, curtains etc.
17. WARNING: Only use aachments/accessories (such as the baery etc.) specied or provided by the manufacturer.
18. WARNING: Refer to the informaon on the underside of the enclosure for electrical and safety informaon before
installing or operang the apparatus.
19. WARNING: To reduce the risk of re or electric shock do not expose this apparatus to rain or moisture. The apparatus
shall not be exposed to dripping or splashing and objects lled with liquids, such as vases, shall not be placed on apparatus.
20. CAUTION: Danger of explosion if baery is incorrectly replaced. Replace only with the same or equivalent type.
21. WARNING: The baery shall not be exposed to excessive heat such as sunshine, re or the like.
22. WARNING: The all-pole mains switch located on rear panel is used as the disconnect device, the switch shall remain
readily operable.
23. WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD.
24. Keep new and used baeries away from children. If the baery compartment does not close securely, stop using the
product and keep it away from children.
25. If you think baeries might have been swallowed or placed inside any part of the body, seek immediate medical
aenon.
Important Safety Instrucons
IPEX5000 Series Quick Install Guide
4
26. When the apparatus is not in use or during its relocaon, take care of the power cord and plugs; e.g. e up the power
cord with cable e or similar. The e must be free from sharp edges and the like that might cause abrasion of the power
cord. When put into use again ensure the power cord and plugs are not damaged. If any damage is found the power cord
and plugs should be replaced by items either specied by the manufacturer or that have same characteriscs as the original
items.
27. This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sucient magnitude to
constute a risk of electric shock.
28. WARNING: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts
inside. Refer servicing to qualied personnel.
29. The exclamaon point within an equilateral triangle is intended to alert the user to the presence of important
operang and maintenance instrucons in the literature accompanying the appliance.
30. Protecve earthing terminal. The apparatus should be connected to a mains socket outlet with a protecve
earthing connecon.
31. CAUTION: To prevent electric shock hazard, replace grille. (CSA 60065, clause 5.3A)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
IPEX5000 Series Quick Install Guide
5
The Digitalinx IP IPEX5001 transmits HDMI video and audio over a 1 gigabit network infrastructure using JPEG2000
encoding with a variable data rate at an average of 250 Mbps with peak values up to 850Mbps. The IPEX5001
supports video signals up to 4K at 60 Hz 4:2:0 / 8 bit deep color, 4K at 24Hz 4:2:0 / 10 bit deep color for HDR10
support, HDCP 2.2 and mulchannel audio support. An analog audio input port embeds analog audio with the
video content, such as a DVI video source. An analog audio output port de-embeds stereo 2 channel audio from
the HDMI content, while sll passing stereo 2 channel audio to the HDMI output.
The IPEX5001 supports PoE power and can be powered remotely via PoE network switch eliminang the need
for a nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass
through mode to control a third party device such as a TV display or HDMI switcher. The USB host port connecon
is for connecng USB host devices such as a computer that is USB 2.0 Full Speed compliant up to 12Mbps that
can communicate with client side devices connected to a decoder. USB roung follows the video route by default
however USB communicaon can be free routed via API. The IPEX5001 features bi-direconal IR support which
follows the video route or can be routed freely via API command.
The IPEX5001 requires a single IPEX5002 for a point to point installaon. When mulple IPEX5001
and/or IPEX5002 devices are in a system, an IPEXCB interface will be required.
Product Overview
IPEX5001 Encoder
The Digitalinx IP IPEX5001-WP-W transmits HDMI or VGA video and audio over a 1 gigabit network infrastructure
using JPEG2000 encoding with a variable data rate at an average of 250 Mbps with peak values up to 850Mbps.
The IPEX5001-WP-W supports video signals up to 4K at 60 Hz 4:2:0 / 8 bit deep color, 4K at 24Hz 4:2:0 / 10 bit deep
color for HDR10 support, HDCP 2.2 and mulchannel audio support. An analog audio input port embeds analog
audio with the video content, such as a DVI video source. An analog audio output port de-embeds stereo 2 channel
audio from the HDMI content, while sll passing stereo 2 channel audio to the HDMI output. The HDMI and VGA
inputs on the IPEX5001-WP-W are auto switching and follow the last in / rst out method and must be physically
connected / disconnected to engage the auto switch.
The IPEX5001-WP-W supports PoE power and can be powered remotely via PoE network switch eliminang the
need for a nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass
through mode to control a third party device such as a TV display or HDMI switcher. The USB host port connecon
is for connecng USB host devices such as a computer that is USB 2.0 Full Speed compliant up to 12Mbps that can
communicate with client side devices connected to the decoder. USB roung follows the video route by default
however USB communicaon can be free routed via API. The IPEX5001-WP-W features a built in IR receiver built in
on the plate, IR follows the video route or can be routed freely via API command.
IPEX5001-WP-W Encoder
IPEX5000 Series Quick Install Guide
6
The Digitalinx IP IPEX5002 receives HDMI video and audio over a 1 gigabit network infrastructure using JPEG2000
encoding from the IPEX5001 and IPEX5001-WP-W encoder. The IPEX5002 outputs video signals navely from
source or can be scaled to 1080p or 4K at 24/30Hz 4:4:4 with HDR10, HDCP 2.2 and mulchannel audio support.
An analog audio output port de-embeds stereo 2 channel audio from the HDMI content while sll passing stereo 2
channel audio to the HDMI output. Depending on the needs of the installaon, mulple IPEX5002 devices can be
congured to make a video wall up to a 16x16 conguraon.
The IPEX5002 supports PoE power and can be powered remotely via PoE network switch eliminang the need for a
nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass through
mode to control a third party device such as a TV display or HDMI switcher. The USB client port connecons is for
connecng USB client devices such as an interacve white board or HID devices that is USB 2.0 Full Speed compliant
up to 12Mbps that can communicate with the host device connected to an encoder. USB roung follows the video
route by default however USB communicaon can be free routed via API. The IPEX5001 features bi-direconal IR
support which follows the video route or can be routed freely via API command.
The IPEX5002 requires a single IPEX5001 for a point to point installaon. When mulple IPEX50012
and/or IPEX5001 devices are in a system, an IPEXCB control box will be required.
IPEX5002 Decoder
The Digitalinx IP IPEX5001-D transmits HDMI video and audio over a 1 gigabit network infrastructure using JPEG2000
encoding with a variable data rate at an average of 250 Mbps with peak values up to 850Mbps. The IPEX5001-D
is Dante enabled meaning that the encoder can on ramp two channel stereo audio either from the embedded
HDMI audio stream or the analog audio 3.5mm input onto a Dante audio network. The mulcast video and Dante
audio IP streams are integrated into one Ethernet cable simplifying networked audio and video soluon into one.
An analog audio output port de-embeds stereo 2 channel audio from the HDMI two channel stereo embedded
stream, while sll passing stereo 2 channel audio to the HDMI output. The IPEX5001-D supports video signals up to
4K at 60 Hz 4:2:0 / 8 bit deep color, 4K at 24Hz 4:2:0 / 10 bit deep color for HDR10 support and HDCP 2.2 support.
The IPEX5001-D supports PoE power and can be powered remotely via PoE network switch eliminang the need
for a nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass
through mode to control a third party device such as a TV display or HDMI switcher. The USB host port connecon
is for connecng USB host devices such as a computer that is USB 2.0 Full Speed compliant up to 12Mbps that can
communicate with client side devices connected to the decoder. USB roung follows the video route by default
however USB communicaon can be free routed via API.
IPEX5001-D Encoder
IPEX5000 Series Quick Install Guide
7
Package Contents per Device
1. Installaon Guide
2. Power Supply with US, UK, EU, and AU adapters
3. 3-pin Removable Screw Terminal
4. Mounng Ears (2 ea)
5. IR Emier
6. IR Receiver
1. Installaon Guide
2. Power Supply with US, UK, EU, and AU adapters
3. 3-pin Removable Screw Terminal
4. Mounng Ears (2 ea)
5. IR Emier
6. IR Receiver
1. Installaon Guide
2. (1) Phoenix 2 pin male connector (3.5mm)
3. (1) 2 gang wall plate decora plasc cover with screws
4. (4) Mounng screws
1. Installaon Guide
2. Power Supply with US, UK, EU, and AU adapters
3. 3-pin Removable Screw Terminal
4. Mounng Ears (2 ea)
5. IR Emier
6. IR Receiver
IPEX5001
IPEX5001-D
IPEX5001-WP-W
IPEX5002
IPEX5000 Series Quick Install Guide
8
Front and Rear Panels
IPEX5001 Front Panel
12 3 4
1. Power indicator
2. Status indicator
3. RS232 Funcon Switch
4. DIP Switch for ID Modes
IPEX5001 Rear Panel
A. 12V DC power input
B. RESET buon
C. LAN connecon with PoE support
D. Analog audio input
E. Analog audio output
F. RS232 connecon
G. USB Host connecon
H. HDMI input
I. HDMI output
J. IR input
K. IR output
IN
ANALOG AUDIO
OUT USB HOST
A B C D E F G H I J K
IPEX5000 Series Quick Install Guide
9
IPEX5001-WP-W Front Panel
1. VGA input port
2. Audio input port (embedded with VGA source)
3. HDMI input port
4. Link LED
• When SOLID: encoder is connected to connected to both an acve source and decoder
• When Blinking: encoder is disconnected from an acve source or decoder
• When OFF: encoder is powered o or network is down
5. Power LED
• When SOLID: device is powered on
• When OFF: encoder is powered o or network is down
6. Factory reset
7. IR receiver / sensor
8. RS232 control port
9. USB host port
1. DC12 DC power input
2. LAN connecon with PoE support
IPEX5001-WP-W Rear Panel
IPEX5000 Series Quick Install Guide
10
IPEX5001-D Front Panel
IPEX5001-D
12 3 4
1. Power indicator
2. Status indicator
3. RS232 Funcon Switch
4. DIP Switch for ID Modes
IPEX5001-D Rear Panel
A. 12V DC power input
B. RESET buon
C. LAN / Dante connecon with PoE support
D. Analog audio input
E. Analog audio output
F. RS232 connecon
G. USB Host connecon
H. HDMI input
I. HDMI output
J. IR input
K. IR output
IN
ANALOG AUDIO
OUT USB HOST
LAN / Dante
A B C D E F G H I J K
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere DigitaLinx Medienkonverter Handbücher
DigitaLinx
DigitaLinx IPEX5000 Series Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HDCAT-WP Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HDCP-C Bedienungsanleitung
DigitaLinx
DigitaLinx DL-VHD Bedienungsanleitung
DigitaLinx
DigitaLinx DL-HDCAT Bedienungsanleitung
DigitaLinx
DigitaLinx EDU-KIT-001 Bedienungsanleitung
