Digitus U1233 Bedienungsanleitung

1/ 15

802.11ac Wireless USB Adapter

U1233, WU1200

User Manual

Company: HAOLIYUAN (SHENZHEN) ELECTRONIC CO., LTD

Name / Position: Albee shen / PM Tel:+1-626-271-1588ext.818861350

Fax:+1-626-271-1588ext.818861350 Email:A[email protected] Address:17708

Rowland Street. City of Industry, CA 91748 United States

2/ 15

Chapter 1. Introduction

Thank you for purchasing the wireless 802.11b/g/n/a/ac USB

adapter! This adapter is mini size design and you are able to plug it

into the USB port. Excepting common wireless standards

802.11b/g/n, this wireless adapter is also 802.11ac compatible -

data transfer rate is 300/867Mbps.

1.1 Product Features

◆Complies with IEEE 802.11ac , IEEE 802.11a,IEEE 802.11n, IEEE

802.11g and IEEE 802.11b standards

◆Provides USB2.0 connector

◆Provides 300/867Mbps receiving rate and 300/867Mbps sending

rate

◆Supports 20MHz/40MHz/80MHz frequency width

◆Auto-detects and changes the network transmission rate

◆Provides two work modes: Infrastructure and Ad-Hoc

◆Supports 64/128-bit WEP, WPA, WPA2 encryption methods and

802.1x security authentication standard

◆Supports WPS (Wi-Fi Protected Setup) encryption method to free

you from remembering long passwords

◆Easy-to-install, plug and play

◆Supports Windows VISTA/Win7/

Win8/Win8.1/Win10/Linux/Macintosh

1.2 Package contents

The following contents should be found in your box:

◆One Wireless 802.11b/g/n/a/ac USB adapter

◆One CD (include driver/utility/user manual)

Note: If any of the listed contents are damaged or missing, please

contact the retailer from whom you purchased the product for

assistance.

3/ 15

CHAPTER 2: Quick Installation Guide

2.1 Driver Installation

Please follow the following instructions to install your new

wireless USB Adapter:

2.1.1

Insert the USB wireless network card into an empty USB 2.0 port

of your computer when computer is switched on. Never use force

to insert the card, if you feel it‟s stuck, flip the card over and try

again.

2.1.2

The following message will appear on your computer, click

„Cancel / Close‟.

Under Windows Vista and Windows 7

2.1.3

Insert the driver CD into your CD-ROM. You can see autorun

screen below. if not, you can double click „autorun.exe‟ on CD.

4/ 15

Click „Install Driver‟ to start the installation procedure

2.1.4

Once the installation is finished the computer will be asked to

reboot. you can click „Finish‟ and reboot the computer to finish the

installation of driver files.

2.1.5

A new icon will appear near the clock of system tray:

5/ 15

Left-click the icon will launch wireless network configuration

utility, and you can right-click the icon to show the quick menu of

configuration utility. This icon also uses different color to show the

status of wireless connection:

Wireless connection is established, good signal reception.

Wireless connection is established, weak signal reception.

Connection is not established yet.

Wireless network card is not detected.

For detailed instructions of wireless network configuration utility,

please see next chapter.

2.2 Connect to Wireless Access Point

To use wireless network, you have to connect to a wireless

access point first. You can either use Client utility (comes with

network card driver), or Windows Zero Config utility (comes with

Windows operating system).

2.2.1 Using Client Utility

Please follow the following instructions to use Client

configuration utility to connect to wireless access point.

1. Left-click the Client configuration utility icon located at

lower-right corner of computer desktop, and configuration menu

will appear:

HERE!

2. Wireless utility will appear. Click „Available Network‟ menu to

search for wireless access points nearby.

6/ 15

3. Please wait for a while, and all wireless access points which can

be reached by this wireless network card will be displayed here.

7/ 15

If the wireless access point you wish to connect does not appear

here, you can click „Refresh‟ button to scan for wireless access

points again; if the wireless access point you‟re looking for still not

appear, try to move the computer closer.

When the access point you‟re looking for is on the list, left-click it

and then double click it or click „Add to Profile‟.

4. If a password (Network Key) is required to access the wireless

access point, please input it in „Network key‟ (and input it again in

„Confirm network key‟ for confirmation). Click „OK‟ when

password is properly inputted.

8/ 15

5. Network card will attempt to connect to access point now, this

may require few seconds to minutes, please be patient. When the

„Status‟ become „Associated‟, your computer is connected to

access point you selected. Click „Close‟ to close configuration

menu.

9/ 15

NOTE: If you connected to an access point but the connection has

been dropped soon, please check security settings and re-check

password spelling.

2.2.2 Using WPS Connect

Wi-Fi Protected Setup (WPS) is the latest wireless network

technology which makes wireless network setup become very

simple. If you have WPS-enabled wireless access point, and you

want to establish a secure connection to it, you don‟t have to

configure the wireless access point and setup data encryption by

yourself. All you have to do is to go to the WPS setup page of this

wireless card, click a button, and then press a specific button or

enter a set of 8-digit code on the wireless access point you wish to

establish a secure connection - just three simple steps!

For older wireless access points, it‟s possible to perform a

firmware upgrade to become a WPS-enabled access point. Since

they may not have a hardware button to press for WPS setup, you

can use an alternative WPS setup method - input the pin code.

Every WPS-compatible wireless network card support pin code

configuration method; you can just input the code to wireless

access point, and the wireless access point and wireless network

card will do the rest for you.

This wireless network card is compatible with WPS. To use this

function, the wireless access point you wish to connect to must

support WPS function too. Now, please follow the following

instructions to establish secure connection between WPS-enabled

wireless access point and your wireless network card.

This wireless network card supports 2 kinds of WPS: PIN code

and Push-Button.

Please follow the following instructions to setup WPS:

1. Right-click Client configuration utility icon, and click „Open

Config Utility‟.

10 / 15

2. Click „Wi-Fi Protect Setup‟ menu.

3. You can use PIN code or Push-Button configuration, and

WPS-compatible wireless access point must use the same type of

WPS. For instructions on setup each type of WPS, see next 2

chapters for detailed instructions.

PIN Code

To use PIN Code, please click „Pin Input Config (PIN)‟ button:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus Adapter Handbücher

Digitus

Digitus DN-7044-1 Bedienungsanleitung

Digitus

Digitus DN-7053 Bedienungsanleitung

Digitus

Digitus WNP-UA300-01 Bedienungsanleitung

Digitus

Digitus DN-30210 Bedienungsanleitung

Digitus

Digitus DA-70878 Bedienungsanleitung

Digitus

Digitus DN-70440-1 Bedienungsanleitung

Digitus

Digitus DN-10150-1 Bedienungsanleitung

Digitus

Digitus DA-70148-4 Bedienungsanleitung

Digitus

Digitus DA-70833 Bedienungsanleitung

Digitus

Digitus DN-30211 Bedienungsanleitung

Digitus

Digitus DA-70858 Bedienungsanleitung

Digitus

Digitus DN-7045 Bedienungsanleitung

Digitus

Digitus DN-3023 Bedienungsanleitung

Digitus

Digitus DA-70300-1 Bedienungsanleitung

Digitus

Digitus DN-70031 Bedienungsanleitung

Digitus

Digitus DA-70840 Bedienungsanleitung

Digitus

Digitus DN-7003GS Bedienungsanleitung

Digitus

Digitus DN-3023 Bedienungsanleitung

Digitus

Digitus DN-10050-1 Bedienungsanleitung

Digitus

Digitus DA-70841 Bedienungsanleitung

Digitus

Digitus DA-70156 Bedienungsanleitung

Digitus

Digitus DA-70831 Bedienungsanleitung

Digitus

Digitus DN-15021 Bedienungsanleitung

Digitus

Digitus DA-71101 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung