Digitus DC-11101-1 Bedienungsanleitung

(Audio support optional)

User’s Manual

1. Introduction

Thank you for your purchasing our KVM Switch! You now have a high quality, durable

system that will enable you to control 2/4 Host computers and/or servers by using PS/2

and/or USB Connectors from one console (PS/2 or USB Mouse, PS/2 or USB Keyboard

and one Monitor) with or without Audio –depending on choosen KVM Switch.

Combo KVMs: DC-11101-1 (2-Port), DC-12101-1 (4-Port),

DC-11301-1 (2-Port, Audio), DC-12301-1 (4-Port,Audio)

USB-PS/2 Combo KVMs: DC-11202-1 (2-Port), DC-12202-1 (4-Port),

DC-11401-1 (2-Port, Audio), DC-12401-1 (4-Port,Audio)

1.1 Features

1. Console your Keyboard/Mouse via either way of PS/2 and/or USB arbitrarily.

2. Complex connections with PCs via either way of PS/2 and/or USB arbitrarily.

3. Controls 2 / 4 computers from a single console (Keyboard/Mouse) over PS/2

and/or USB connections.

4. Supports Windows, Linux, Mac OS9/OSX, Sun Microsystems.

5. Emulates a keyboard on each PC to allow your computers to boot normally -

without a keyboard error.

6. Supports hot-swap.All devices connected to the KVM can be added or removed

at any time, without shutting the unit down.

7. Supports 2 types of switching: (1) Hardware Push Button, (2) Hot-Keys on PS/2

and/or USB of keyboard arbitrarily.

8. Supports Auto-Scan function to alternate video between computers in preset

intervals.

9. Supports LED display for PC status monitoring.

10. Supports VGAresolutions up to 2048 x 1536 @ 85HZ.

11. Supports Beeper during switching enabled.

12. Self powered through PS/2 and/or USB connection.

13. Fully compliant with the USB 1.1/ 2.0 specification.

14. Audio support IN / OUT (only audio version)

1.2 Package Contents

The product you purchased should contain the following equipment and accessories:

1. 2-Port or 4-Port KVM Switch with

PS/2 and/or USB console

ports

2 pcs. KVM cable sets, 1,8m

User Manual

2. Specifications

2.1 General

Specification

Number Of Computers Controlled 2 / 4

Selection Method

Push Button and Hot-Key (PS/2 and/or USB Keyboard)

LEDs Red for PC Selection

Green for PC On-Line ready

Video 2 / 4 x HDB -15 female

( USB & PS/2 signal combined )

Speaker 2 / 4 audio female jacket (only audio version)

Microphone 2 / 4 audio female jacket (only audio version)

PC Connectors

Keyboard 1 x 6 pin PS/2 mini-DIN female

1 x USB Atype female (only USB –PS/2 version)

Mouse 1 x 6 pin PS/2 mini-DIN female

1 x USB A type female (only USB –PS/2 version)

Video 1 x HDB -15 female

Speaker 1 x audio female jacket (only audio version)

Console Ports

Microphone 1 x audio female jacket (only audio version)

Auto-Scan Interval From 5 to 250 Seconds

DDC, DDC2 monitor Yes (Max. Resolution: 2048x1536) @ 85Hz

Hot Swappable Yes

Operating systems supported Windows 98SE/ME/2000/XP/2003 Server, Linux

Mac OS9/OSX and Sun Micro System

Device driver No Need

Power

By PS/2 and/or USB or External Power Adaptor (Optional)

Dimensions (L X W X H) 2-Port : 14.0 x 8.5 x 4.5 cm (5.5 x 3.3 x 1.7 inches)

4-Port : 21.5 x 8.8 x 4.5 cm (8.5 x 3.4 x 1.7 inches)

Unit Weight 2-Port : ~ 450 g

4-Port : ~ 650 g

Housing material Metal

Operating Temperature 32~ 122°F (0~ 50°C )

Humidity 0%~80%RH

3. System Requirements

Console

A VGA, SVGA, Multisync monitor capable of the highest resolution.

PS/2 and/or USB Keyboard/Mouse

Computer or Server

The following equipment must be equipped with each computer or server.

- A VGA, SVGA or Multisync card.

- Type A USB port and/or PS/2 6 pin mini-DIN for Keyboard and Mouse.

Cables

The KVM Switch with USB and PS2 console must be used specific custom 4-in-1 cables.

To purchase the specific cable sets, please contact your dealer.

4. Installation

LED Indicators:

Selected

: RED LED indicates that the KVM Switch is selected to the corresponding PC.

On-Line :

GREEN LED indicates that the KVM Switch is ready to the corresponding PC.

AutoScan

: GREEN LED flash indicates that the KVM Switch is in auto-scan mode.

Reset Switch :

Press this switch for a system reset. This switch must be pushed with a thin object,

for example, such as the end of a paper clip, or a ball point pen.

4.1 Single installation

Precaution:

1. For users who would like to connect PC over PS/2 interface:

Please finish the connection to PC over PS/2 port before turning on PC.

PC will not detect PS/2 devices, if PS/2 is not connected while booting. It will

cause a mouse and keyboard error with no access to your computer.

2. When connecting a Windows 98 system , it is suggested that the PC must be

always plugged to PS/2 ports, because Windows 98 does not support

installation at first time through USB HID installation driver.

3. Some old PCs can support USB keyboard during booting, but are required to

open BIOS USB setting first.

4. For connecting Windows 2000, Window 2003, Window XP or later, in case of

PC is set as “need to be login with the password”and connects to KVM over

USB interface only, it is suggested that complete the installation of the KVM

switch before logging out the Windows system. In these case, the host is able

to recognize the USB HID device and install the driver and makes the KVM

switch works properly in the next booting.

5. The KVM switch is powered by either PS/2 keyboard port or USB port. For

Notebook or Laptop, power might not be strong enough to support KVM switch .

If KVM switch cannot work properly with your Notebook, it is suggested that

using a DC switching power adaptor with 5V/300mA~1A to the KVM power

jacket. For polarity, see following:

6. For USB Keyboard with built-in USB HUB, please note that the KVM

switch does not support the built-in USB HUB on USB keyboard.

Console connecting:

Plug either your USB keyboard, mouse and/or PS/2 keyboard, mouse arbitrarily

and VGA video into the Console ports located on the KVM Switch’s front panel.

( Note: No matter what you plugged even thought USB mouse with PS/2 keyboard

or PS/2 mouse with USB keyboard are available working to the KVM Switch unit.)

System connecting:

Use KVM custom cable sets to connect any available PC ports to the video and

either USB or PS/2 ports alternatively, or even USB & PS/2 both all connected

to the computers you are connecting up.

To purchase the custom KVM cable sets, please contact your dealer.

( Fig 1 ) custom 4-in-1 cable

Improve monitor display quality:

If you are using LCD monitor connected with KVM switch and feel the display

quality is not comfortable to you, please push Auto-Adjusting function

button on monitor panel to improve display quality.

This KVM Switch with custom specific cable set provide three connecting methods.

1. Plug Speaker & Microphone (only audio version), USB, PS/2 (keyboard/mouse)

ports and VGA into PCs at same time, recommended in priority. ( Fig. 2 )

(only audio version)

( Fig. 2 ) Speaker, Microphone,PS/2 & USB and VGA connected at same time.

2. Plug only Speaker, Microphone,PS/2 (keyboard / mouse) ports and VGA into

PCs. ( Fig. 3 )

(only audio version)

( Fig. 3 ) Speaker, Microphone, PS/2 and VGA connected.

3. Plug only Speaker, Microphone,USB and VGA into PCs. ( Fig. 4 ).

(only audio version)

( Fig. 4 ) Speaker, Microphone, USB and VGA connected.

4.2 Rack Mounting ( Optional ) for 4-Port KVM Switch only.

Mounting brackets to the KVM Switch unit for standard 19-inch rack cabinet.

1. Screw the mounting brackets into the sides of the KVM Switch unit.

2. Slide the KVM Switch unit into the rack cabinet and secure it to the rack.

5. Operations

The 2 / 4-Port KVM Switch has the ability to switch the keyboard, video, mouse,

audio, microphone (only audio version) simultaneously.

Note: When using Hot Key, the keys must be pressed within 3 seconds;

otherwise the Hot Key action will be terminated.

5.1 Push Button on front panel

Push the button directly to select the connected PC.

5.2 Hot-Key operation ( PS/2 or USB Keyboard )

Note: If your keyboard is without < Scroll Lock > button, then you can change

the hotkey setting and use < Caps Lock > or <Num Lock > to instead of

Scroll Lock (please refer 5.2.0).

5.2.0 Alternate hotkey selection

Hot Key:

[Ctrl] →[Ctrl] →[Caps Lock] →[Enter] : The hotkey changed to [Caps Lock]

[Ctrl] →[Ctrl] →[Num Lock] →[Enter] : The hotkey changed to [Num Lock]

[Ctrl] →[Ctrl] →[Scroll Lock]→[Enter] : The hotkey reversed to [Scroll Lock]

Note : The default hotkey setting is <Scroll Lock>, after you changing the

hotkey setting, the new setting will effect on the KVM until power off or reset.

5.2.1 PCs Selection

Hot Key:

[Scroll] →[Scroll] →[Enter]

[Scroll] →[Scroll] →[→]

[Scroll] →[Scroll] →[←]

[Scroll] →[Scroll] →[ 1 ] →[Enter] or

[Scroll] →[Scroll] →[ 2 ] →[Enter] or

[Scroll] →[Scroll] →[ 3 ] →[Enter] or

[Scroll] →[Scroll] →[ 4 ] →[Enter]

You can synchronize the PC selection, by using the following two-step Hot Key

sequence. To send commands to the Combo KVM Switch, press the [Scroll] key

twice (Step 1), then press key [1] or [2] or [3] or [4] and [Enter] (step 2) to assign

the PC to a particular PC. (If you press key [1] or [2] or [3] or [4] on the

number pad, the keyboard, mouse & video will also be switched

synchronously. If you do not assign the specific PC number from 1~4, and

just press [Enter] after the twice scroll lock pressing, then the KVM will

switch to next PC. If you press the left arrow key then the KVM will switch

to the forward PC, the right arrow key will switch to next PC.

5.2.2 Auto-Scan Function

Hot Key:

[Scroll] →[Scroll] →[S] →[Enter] to BEGIN.

Any key to STOP.

You can activate the Auto-Scan function by using the following two-step Hot Key

sequence. To send commands to the Combo KVM Switch, press the [Scroll] key

twice (Step 1), then press [S] and then press [Enter] (Step 2). When you press the

Auto-Scan hot key sequence, the Combo KVM Switch alternates between the two or

four PCs and displays them on the monitor.

Each PC is displayed in a time interval from 5 ~ 250 seconds (The interval is

adjustable) before switching to the next. When you press any key on the keyboard,

the Auto-Scan will stop and the monitor screen will jump back to the original PC.

During the Auto-Scan mode, the KVM will ignore the mouse operation, so if you

move mouse you will not see the cursor move on the screen.

Adjustable scan time interval setting ( 5 ~ 250 sec. )

Hot-key: Pressing the <Scroll >, <Scroll > then <S> and <5 ~250 > <Enter>

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus Schalten Handbücher

Digitus

Digitus DS-46100 Bedienungsanleitung

Digitus

Digitus DS-12800 Bedienungsanleitung

Digitus

Digitus DC-11201-1 Bedienungsanleitung

Digitus

Digitus DA-70216 Bedienungsanleitung

Digitus

Digitus DS-48304 Bedienungsanleitung

Digitus

Digitus DN-95104 Bedienungsanleitung

Digitus

Digitus DN-95323-1 Bedienungsanleitung

Digitus

Digitus DN-95301 Bedienungsanleitung

Digitus

Digitus DS-12910 Bedienungsanleitung

Digitus

Digitus DN-80223 Bedienungsanleitung

Digitus

Digitus DS-12883 Bedienungsanleitung

Digitus

Digitus DN-80212 Bedienungsanleitung

Digitus

Digitus DA-70235 Bedienungsanleitung

Digitus

Digitus DN-651135 Bedienungsanleitung

Digitus

Digitus DC-72301 Bedienungsanleitung

Digitus

Digitus DN-50011 Bedienungsanleitung

Digitus

Digitus DN-80064-1 Bedienungsanleitung

Digitus

Digitus DN-651148 Bedienungsanleitung

Digitus

Digitus DS-45310 Bedienungsanleitung

Digitus

Digitus DS-12850 Bedienungsanleitung

Digitus

Digitus DN-95320 Bedienungsanleitung

Digitus

Digitus DN-80120 Bedienungsanleitung

Digitus

Digitus DN-80201 Bedienungsanleitung

Digitus

Digitus DA-70245 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung