Digitus DC-72301 Bedienungsanleitung

- 1 -

LCD KVM SWITCH

DC-72301 / DC-72302 / DC-72401

USER MANUAL

- 2 -

LCD MONITOR SPECIFICATIONS

Size 17 inch

Screen Type TFT

Contrast 500:1

Brightness 300 cd/m2

View Angle 140°

Resolution 1280x1024@75Hz

Response Time 8 ms

Display Color 16.2 M

OPERATION

Keypad Define

Power key: Use this key to turn on or off the LCD monitor.

Menu key: Use this key to open the OSD menu and enter to next menu or to highlight a confirmed

function.

Up key: Use this key to highlight an item in the menu, to move a highlighted function up, or to

increase the numeric value (parameter) in a certain menu.

Down key: Use this key to highlight an item in the menu, to move a highlighted function down, or to

decrease the numeric value (parameter) in a certain menu.

Auto key: Use this key to automatically adjust the image position and phase, and return to the

previous menu or to exit a highlight item.

If the screen is not in a full screen graphic mode (such as in a DOS) or is connected with an

allocator, the position of the appeared image may be adjusted automatically and then deviated. By

then, it is necessary to enter into the OSD menu to manually adjust the level or vertical position and

phase.

- 3 -

OSD Control Function List

1. Color:

Contrast

Brighthess

Color Adjust

Color Temp.: 9300, 6500, 5800, 5RGB, USER

Exit

2. Image Setting:

Clock

Phase

Gamma

Sharpness

Exit

3. Position:

H.Position

V.Position

Exit

4. OSD Menu:

OSD H.Pos

OSD V.Pos

OSD Timer

Exit

5. Language:

English, Français, Deutsch, Español, 繁體中文, 简体中文, 日本語

6. Misc.:

Signal Source

Reset

Factory Mode

Exit

7. Exit

- 4 -

BRIEF INTRODUCTION

The KVM Switch allows you to control several sets of personal computers by a keyboard, a mouse

and a monitor. In the meantime, you just need to connect the cable and turn on the power to

control up to 256 sets of personal computers without installing any additional interface card or

software.

Easy Installation

The 3-in-1 CPU Connector (VGA, Keyboard and Mouse) can save the installation time and space

and assure the correct signals. The universal AC power input of 100~240VAC, 50Hz~60Hz saves

you the trouble of finding the space for installing the Power Adaptor. You can install a cascade to

facilitate expansions or transportation without requiring a cascade cable or changing the KVM

configurations.

On-Screen Display (OSD) Menu

The embedded OSD control module lets you name the PC and KVM and modify the KVM

configuration, and the security mode can prevent others from turning on the KVM by mistake and

switching the linked PC from the OSD. Most conveniently, the OSD not only supports keyboard

operations, but also supports mouse clicking.

Enhanced Video Quality

The special video circuit design supports resolution up to 1280x1024, 75Hz, and also keeps the

same quality under the Cascade architecture.

PACKAGE INSIDE

KVMSwitch x 1

USERManual x1

PowerCord x1

F/W Update Cable x 1

Rack-Mount Brackets x 2

Screws (for Brackets) x 12

Key x2

- 5 -

FEATURES

‧ The keyboard, mouse and 17” LCD monitor were built-in on the KVM switch.

‧ Standalone machine controls up to 4/8/16 sets of PCs.

‧ Cascade controls 64/128/256 sets of PCs.

‧ Through OSD, you can use the hot key, mouse clicking and push button on front panel to switch

PCs.

‧ Monitors PC status by Auto Scan function.

‧ Supports resolution of 1280x1024, 75Hz and independently supports EDID & DDC2 of each PC.

‧ Each Port on the panel of the KVM has independent push buttons and LED lamps for easy

switch and identification.

‧ Complies with the height of the 1U chassis specification and installable with a hanging stand

into a 19” chassis system.

‧ Requires no additional software or hardware.

‧ Supports hot plug; not necessary to turn off the original system regardless of a newly installed

PC or KVM.

EQUIPMENT REQUIREMENTS

Computer System

• A Supported VGA, SVGA, XGA, SXGA or Multisync Video Card.

• A PS/2 (mini-DIN 6Pin) Mouse port.

• A PS/2 (mini-DIN 6Pin) or AT (5-Pin DIN) with AT-to-PS/2 Adaptor Keyboard port.

Cable

• 3-in-1 KVM Cable; please contact your local distributor for detailed specification and length.

Connected to CPU port of KVM Connected to Console port of PC or Slave KVM

- 6 -

SPECIFICATIONS

DC-72301 DC-72302 DC-72401

CPU

Connecter

3-in-1

HD-15 (Female) 4 8 16

Console

Connector

Monitor 17” TFT LCD

Mouse Touch pad module

Keyboard Standard 104 keys

Port Selection Keys on

Front Panel 4 8 16

LEDs Port 4 8 16

Power 1 1 1

OSD Built-in

Video Resolution 1280x1024@75Hz

Dimensions 600x450x48 mm

Weight 13.3 Kg 13.35 Kg 13.4 Kg

Operating Temp 5-40

Storage Temp -20~60

Humidity 10~80%RH, non-condensing

- 7 -

CONFIGURATION

DC-72301 Front View

DC-72302 Front View

DC-72401 Front View

1. Port Selection Switches

•Press the push button to directly switch to the corresponding PC.

•In the cascade architecture, if the port is connected to KVM but not PC, then the push button

will not respond.

•Simultaneously press Push Buttons 1 and 2 to directly enter the OSD Control Mode.

2. Port LEDs

These Port LEDs are built in the Port Selection Switches.

Online: A green light indicates that the PC or KVM connected to the corresponding port is on

and operating.

Selected: A red light indicates the situation of being connected to the port.

If a port is connected to KVM, then the red light of that port will not on.

Besides the special mode, the whole system architecture only has one red light (indicating that

the Console is connecting to the PC) or has no red light (when powering on the KVM for the

first time.)

3. Power LED

An blue light indicates that the KVM is operating.

- 8 -

DC-72301 Rear VIEW

DC-72302 Rear VIEW

DC-72401 Rear VIEW

1. CPU Port

Install the cable connected to a PC here.

2. Update Port

The port provides a firmware update function.

3. AC Power Jack

The AC Power is applicable for 100~240VAC, 50Hz~60Hz

4. 4. Power Switch

Power On/Off the LCD KVM.

- 9 -

INSTALLATION

Standalone

1. Make sure that the power switch at the rear panel of the KVM is OFF. Plug an end of the AC

power cord into the KVM and the other end to an AC power supply.

2. Make sure to power off the PC and then install the 3-in-1 cable to each of the PC one by one.

Note: If the ON-LINE LED (Green) of any port of a PC is on, then we recommend you to

power off such PC (Turn off the power switch of the power supply of the PC or unplug the

power cable of the PC) or wait till Step 4 to install that particular PC.

3. Turn on the power switch at the rear panel of the KVM.

4. Power on the PC.

Note:

It is not necessary to power down the whole system for install a new PC or KVM thereafter.

All you need is to make sure that the new PC or KVM is OFF during the installation. If the

KVM powers down due to external factors (such as power failure or the power of the KVM is

turned off), we recommend you to reinstall the whole system.

Connection in Series

1. Make sure that the power switch at the rear panel of the Master KVM is OFF. Plug one end

of the AC power cord to the KVM and the other end to the AC power supply.

2. Make sure the power switches at the rear panels of all slave KVMs are OFF. Plug one end

of the AC power cord to the KVM and the other end to the AC power supply.

3. Install the Master KVM to the 3-in-1 cable (same as the cable for connecting the KVM to the

PC) in the middle of the Slave KVMs.

4. Make sure the power of the PC is OFF and then install the 3-in-1 cable to each PC one by

one.

Note: Install the PCs on the master or the PCs on the Slave first. If the ON-LINE LED (Green)

of any port of a PC is on, then we recommend you to power off such PC (Turn off the power

switch of the power supply of the PC or unplug the power cable of the PC) or wait till Step 7

to install that particular PC.

5. Turn on the power switch at the rear panel of the master KVM.

6. Turn on the power switch at the rear panel of the slaver KVM.

- 10 -

7. Power on the PC.

Note: It is not necessary to power down the whole system for install a new PC or KVM

thereafter. All you need is to make sure that the new PC or KVM is OFF during the

installation. If the KVM powers down due to external factors (such as power failure or the

power of the KVM is turned off), we recommend you to reinstall the whole system.

Note:

It is noteworthy that there are two levels available.

Expansion

1. PCs

It is not necessary to power down the KVM or other computer connected to the KVM system.

You only need to power off the desired PC and connect the PC to the CPU port of the KVM

in parallel by the 3-in-1 cable, and then power on the PC.

2. Slave KVM

Make sure the power switch at the rear panel of the KVM is OFF. Use the AC power cord

(3-in-1 cable) to connect the console port of the slave KVM to the CPU port of the master

KVM. Power on the slave KVM.

For example:

If you want to install one Slave KVM and three PCs, then just follow Step 2 of the foregoing method

to add the slave KVM and install the PCs one by one according to Step 1.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus Schalten Handbücher

Digitus

Digitus DS-16100 Bedienungsanleitung

Digitus

Digitus DN-60021-1 Bedienungsanleitung

Digitus

Digitus DS-45333 Bedienungsanleitung

Digitus

Digitus DS-15202-1 Bedienungsanleitung

Digitus

Digitus DA-70236 Bedienungsanleitung

Digitus

Digitus DN-651154 Merkblatt

Digitus

Digitus DN-95331 Bedienungsanleitung

Digitus

Digitus DS-45312 Bedienungsanleitung

Digitus

Digitus 4-Port Desktop USB KVM Switch with USB 2.0... Bedienungsanleitung

Digitus

Digitus DN-95323-1 Bedienungsanleitung

Digitus

Digitus DN-95311 Bedienungsanleitung

Digitus

Digitus DA-73301 Bedienungsanleitung

Digitus

Digitus DA-70245 Bedienungsanleitung

Digitus

Digitus DN-8021B Bedienungsanleitung

Digitus

Digitus DN-651132 Bedienungsanleitung

Digitus

Digitus DN-80113 Bedienungsanleitung

Digitus

Digitus DN-652120 Bedienungsanleitung

Digitus

Digitus DA-73300-2 Bedienungsanleitung

Digitus

Digitus DN-651160 Bedienungsanleitung

Digitus

Digitus DS-45320 Bedienungsanleitung

Digitus

Digitus DN-95301 Bedienungsanleitung

Digitus

Digitus DS-45310 Bedienungsanleitung

Digitus

Digitus DA-70224-1 Bedienungsanleitung

Digitus

Digitus DS-12820 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung