Dimplex QSH-70 Bedienungsanleitung
IMPORTANT SAFETY INFORMATION: Always read this manual rst before attempting to install or use this
Heating System. For your safety, always comply with all warnings and safety instructions contained in this
manual to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit www.dimplex.com 7212670100R04
Owner’s Manual
Quantum Storage Heater
Models: QSH-70 QSH-100 QSH-125 QSH-150
Boost Output
208/240V~ 473/630W 660/880W 848/1130W 1035/1380W
Rated Input
208/240V~ 1170/1560W 1665/2220W 2070/2760W 2478/3300W
Rated Output for 8hr
Charge Period 700W 1000W 1250W 1500W
# of Bricks
(3 Bricks per Package) 18 24 30 36
Installed Weight 91 kg
(200 lbs)
115 kg
(254 lbs)
142 kg
(313 lbs)
165 kg
(364 lbs)
kWh 10.9 kWh 15.4 kWh 19.3 kWh 23.1 kWh
2 www.renewables.dimplex.com
Table of Contents
Welcome & Congratulations ........................................................3
IMPORTANT INSTRUCTIONS ......................................................4
Quick Reference Guide ............................................................5
General Introduction ..............................................................5
The Benets of Quantum ..........................................................5
Choosing a Location ..............................................................5
Site Selection and Preparation ......................................................6
Installation Instructions ............................................................7
Electrical Connections ............................................................7
Building the Center Core ..........................................................8
Reassembly ....................................................................9
Operation ......................................................................10
Controls ......................................................................10
Control Functions ...............................................................10
Setting the Date and Time ........................................................11
Choosing and Setting a Timer Mode ................................................11
Boost. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Options .......................................................................13
Child Lock .....................................................................13
User Information ................................................................13
Service Menu ..................................................................13
Maintenance ...................................................................14
Warranty .....................................................................15
Quantum - Quick Set-Up Sheet and Settings Records ......................................16
Always use a qualied technician or service
agency to repair this system.
!NOTE: Procedures and techniques that are
considered important enough to emphasize.
CAUTION: Procedures and techniques which,
if not carefully followed, will result in damage to
the equipment.
WARNING: Procedures and techniques which,
if not carefully followed, will expose the user to
the risk of re, serious injury, or death.
3
Welcome & Congratulations
DO NOT COVER
Model:
Serial:
Series:
Thank you and congratulations for purchasing a Quantum Storage Heating System from
Dimplex. Please use our convenient online registration page to record your model and
serial numbers for future reference at
www.dimplex.com/register
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
In order to better serve you, please have your model and serial number
ready or register your product online before calling (See above)
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before starting installation.
Failure to follow these instructions may result in a possible electric shock, re hazard
and will void the warranty.
4 www.renewables.dimplex.com
SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electric
shock and injury to person, including the following:
1. Read all instructions before using this heater.
2. Heater and controls should be installed by a qualied contractor. Wiring procedures and connections should
be in accordance with the National Electric Code (CEC & NEC) and local codes.
3. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or ammable
liquids are used or stored.
4. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible ma-
terials such as: furniture, pillows, bedding, papers, clothes and curtains away from heater.
5. To prevent a possible re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces like a
bed where openings may become blocked.
6. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
shock or re, or damage the heater.
7. Do not install these heaters against combustible, low density cellulose bre surfaces or vinyl wall paper.
8. Do not locate these heaters below any electrical convenience receptacles.
9. Quantum heater are not suitable for installation in bathrooms or areas of high humidity.
10. Check nameplate ratings to be sure the heater voltage is the same as the service supply.
11. HIGH TEMPERATURES: Keep electrical cords, furniture, draperies or any other blocking material away from
the heater. See Installation Section for specic distances.
12. The heater is very heavy and must be secured to a wall to ensure that it cannot move.
5
Quick Reference Guide
General Introduction
This storage heater heats its highly insulated stor-
age core of dense ceramic material at preselected
times to meet the day’s heating requirements.
When heat is required throughout the day, the
heater releases its stored heat by a silent ther-
mostatically controlled fan. The Dimplex control
system automatically stores more energy as it
gets colder, keeping you warm and comfortable no
matter the outdoor conditions. Additional boost ele-
ments are incorporated to ensure consistent com-
fort if the core ever runs low on energy.
The Benets of Quantum
Quantum is designed to be a responsive heating
system that meets your comfort requirements while
optimizing energy use. The heater releases heat in
two ways:
• A small amount of heat is dispersed by ‘natu-
ral’ convection and radiation from the heater
case.
• The vast majority of heat is released using the
built-in fan that pushes hot air out from the
heat outlet grille at the bottom of the product.
Minimizing the release of stored heat from the
outer casing means that more energy is available
when warmth is required. This makes more ef-
cient use of the stored energy as you can ‘turn off’
the heater when you are out or do not need it.
Choosing a Location
Compared with traditional storage heaters the
amount of energy released from the outer case
of the heater is signicantly reduced. This allows
more efcient running because the Quantum is
heating the room only when you want it to.
!NOTE: Occasional clicking sounds during
operation are due to temperature changes in the
storage core.
When determining a location for the Quantum Stor-
age Heater ensure that no objects are closer than
300 mm (11.8”) in front of the unit, 100 mm (3.9”)
on either side or 250 mm (9.8”) above the heater.
(Figure 2)
!NOTE: The new material in the heater will pro-
duce a slight smell for the rst few days of opera-
tion.
CAUTION: Rooms must be well ventilated and
your children, cages birds, or persons with respira-
tory complaints must not remain in close proximity
to the heater during the rst 48 hours of the start-
up period of each heater.
!NOTE: During rst operation of the fan you may
notice a small amount of dust discharged from the
air outlet grille at the bottom of the product.
Controls
Heat Outlet Feet
Front
Panel
Figure 1
Figure 2
250 mm (9.8”)
100 mm
(3.9”)
100 mm
(3.9”)
300 mm (11.8”)
6 www.renewables.dimplex.com
Site Selection and Preparation
1. Place the heater at on the ground with arrows
printed on the base of the carton pointing
upwards. Open the carton at the bottom, slide
the heater out of the carton exposing the
feet and the hardware kit located within the
packaging on the right hand side. Remove the
feet and the hardware kit.
2. Secure the feet to the heater, using the screws
provided in the hardware kit.
!NOTE: For models QSH-70 and QSH-100
two locations are possible for mounting each
foot. They are indicated by an “X” and “Y”
marking visible on the base of the heater.
3. Ensure the feet are secured at the location
holes marked with an “X”, see Figure 3.
4. Stand the heater on its feet before removing
the packaging.
5. Once the feet have been secured and the unit
has been turned upright, remove the grille from
the side of the unit. (Figure 4)
6. Remove the two screws located towards the
bottom at each end of the heater, which retain
the heater sides. (Figure 5A)
7. Push the end panels vertically upwards to
release each side from its securing points.
(Figure 5B)
8. Remove the two screws securing the front
panel, located at the upper sides of the heater,
and swing the upper edge of the front panel
forwards and unhook it from along the heater
base. (Figure 6)
Figure 4
Figure 5
A
B
Figure 6
Figure 3
7
Installation Instructions
WARNING: This appliance is heavy. The oor
must be checked to ensure that it is capable of
bearing the weight of the unit up to 177 kg (390
lbs).
WARNING: Do not under any circumstances
attempt to move or reposition this heater without
seeking expert advice.
CAUTION: The heater must be securely xed to
a wall before operation.
CAUTION: Do not install the unit on carpet or
any other soft surface. If installing in a carpeted
area remove the carpet and underlay so that the
feet rest directly on the oor. Ensure that the unit is
level.
1. Place the heater in its nal position and mark
the xing holes through the location holes
visible through the back of the heater.
Mark the xing positions at the two extreme
ends of the heater with the heater pushed tight
against the wall.
Remove the wall bracket from the heater by
removing the two screws at each end of the
bracket. Place the heater to one side and
position the bracket against the wall aligning it
with the location marks.
2. Six screw locations, on the bracket, must be
selected for each model. Mark the positions for
the screw holes. Remove the bracket from the
wall, drill the holes and mount the bracket using
the appropriate hardware for that particular type
of wall.
3. Secure the heater to the bracket using the
screws previously removed.
CAUTION: Under no circumstances should
these screws be removed without rst removing all
bricks from the heater.
Electrical Connections
WARNING: The installation of this appliance
should be carried out by a competent electrician
and be in accordance with National Electrical
Codes (NEC) and local codes.
1. The heater is factory congured to operate with
one main power supply.
2. Storage/Fan Circuit:
• Ensure the black wire is connected to the
Mounting Holes
Figure 7
Figure 8
8 www.renewables.dimplex.com
Installation Instructions
terminal marked L1.
• Ensure the red wire is connected to the
terminal marked L2.
• The ground wire should be connected to the
terminal marked E or .
!NOTE: For 208V installations the wiring must be
modied for the motor to operate correctly.
• 208V installations ONLY: Disconnect the blue
wire on T6 and connect it to T5.
3. The main power entry clamp and terminal block
will be visible on the right hand side of the unit.
Insert the power cables through the opening at
the bottom of the heater and connect. (Figure
9)
CAUTION: Only heat resistant wiring should be
used, capable of withstanding temperatures up to
90°C (194°F).
Building the Center Core
1. Remove the inner panel to access the core of
the heater. Lay the inner panel carefully to one
side to ensure it is not damaged. (Figure 10)
2. Remove any internal packaging.
3. The bricks have several grooves on one
surface for locating around the elements. The
two slots through the centre of the brick create
the air passages within the core.
4. Position the rst brick of the bottom row to the
right rmly pressed against the side insulation
with the element grooves facing upwards and
tting neatly around the element. Angle the
element upward to t the brick and the air
passages line up with the holes in the base
insulation.
CAUTION: Do not disconnect the element
terminals
5. Fit the remaining bricks in the bottom row being
careful not to damage or dislodge the element.
6. Position the second row of bricks so that they
are facing down and the element sits within the
grooves. (Figure 11)
Wire Entrance Cable Clamp
Terminal
Block
L2
L1
G
Figure 9
Figure 10
208/240V Installations
T5
T6
9
Installation Instructions
7. The third row of brick is positioned in a manner
similar to the rst row.
CAUTION: Be careful not to damage or
dislodge the element.
8. Repeat the pattern for the remaining rows.
9. Check that all the bricks are secure and evenly
located.
10. Close the core by replacing the inner panel
complete with insulation.
11. Ensure the bottom edge is located inside the
chassis and that the screws are tightly secured
at each edge.
!NOTE: Double check all wiring connections
are secure and any excess cable is restrained
and cannot come in contact with any of the
heater casing. Under no circumstances should
any excess cable be pushed inside or behind the
heater.
CAUTION: Once installed do not attempt to
reposition the heater without rst unloading the
bricks.
Figure 11
Reassembly
1. Replace all the panels of the outer casing
reverse steps 5-8 of Site Selection and
Preparation Section.
2. Ensure all of the hardware has been tightened.
3. Clean the outlet grille and adjacent surfaces
after the rst operation as some dust may be
produced when the heater is rst used.
In cases where unauthorized persons may tam-
per with the control settings it is possible to set a
tamper-proof feature at the time of installation, by
pressing and holding the Back button and the Se-
lector Dial simultaneously for three seconds, ‘Child
Lock’ will appear on the screen, repeat to reverse.
See the Operating Instructions for further details.
10 www.renewables.dimplex.com
Operation
CAUTION: During the initial operation some
odor may be noticed due to the newness of materi-
als used in manufacturing. This is normal and will
disappear after a short period of use. It is however
advisable to keep the room well ventilated. Rooms
must be well ventilated and young children, caged
birds, or persons with respiratory complaints must
not remain in close proximity to the heater during
the rst 48 hours of the commissioning period. This
must be done for each heater (staggered over a
few days).
Controls
The user controls are located on the top right of
the heater. The heater is tted with an adjustable
electronic temperature controller and three but-
tons.
1. Display Screen
2. “Menu” Button
3. “Back” Button
4. “Advance” Button
5. “Selector Dial”
The minimum room temperature setting is 7°C
(45°F) and may be used for protection against
frost. The maximum temperature setting available
is 30°C (86°F).
A temperature of approximately 20°C (68°F) repre-
sents a normal room temperature.
It is normal for the fan to stop running for periods
of time. This happens because the room tem-
perature is at or above the temperature set on the
control and the room does not need any more heat
at that time.
Control Functions
The heater controls can easily be adjusted by
using a combination of the three buttons and the
selector dial, which can be rotated and pressed.
1. DISPLAY SCREEN shows the options avail-
able at each stage of the adjustment. COM-
FORT ON/OFF illustrates the part of the time
function that is currently running.
Comfort On – will control the room to the
set temperature.
Comfort Off - will control the room to the
setback temperature.
Boost Mode - includes an auxiliary boost
element to ensure consistent comfort if the
core ever runs low on energy.
2. MENU displays the options available;
Date/Time - Setting current date/time.
Timer Mode - Setting the timer to your indi-
vidual requirements.
Boost – Enables the auxiliary boost ele-
ment to work automatically. Associated
timer can be set to operate heater for 1 – 4
hours at a time.
Options - Temperature formats, ‘Daylight
Saving’ settings, and Setback settings.
3. BACK shows previous programming stage.
4. ADVANCE button on the User Interface is
used to skip from the current Comfort mode
to the next – turning the heater from OFF to
ON or vice versa.
Andere Handbücher für QSH-70
1
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Dimplex Heizung Handbücher
Dimplex
Dimplex FX 20V Bedienungsanleitung
Dimplex
Dimplex PLXE Series Bedienungsanleitung
Dimplex
Dimplex DHCER24SG Bedienungsanleitung
Dimplex
Dimplex Girona GFP050E Bedienungsanleitung
Dimplex
Dimplex 7150B11 Bedienungsanleitung
Dimplex
Dimplex RFI-D Series Bedienungsanleitung
Dimplex
Dimplex BS 120 Bedienungsanleitung
Dimplex
Dimplex XT Bedienungsanleitung
Dimplex
Dimplex DHCER20FE Bedienungsanleitung
Dimplex
Dimplex AC3RN Bedienungsanleitung
Dimplex
Dimplex BRENTA BNT20 Bedienungsanleitung
Dimplex
Dimplex FFIH15A31 Series Bedienungsanleitung
Dimplex
Dimplex 402E Bedienungsanleitung
Dimplex
Dimplex CFS60E Bedienungsanleitung
Dimplex
Dimplex WFE 3TNB Bedienungsanleitung
Dimplex
Dimplex Evo Rad Bedienungsanleitung
Dimplex
Dimplex ARC10E Bedienungsanleitung
Dimplex
Dimplex DDF250 Beilage
Dimplex
Dimplex RSH Series Bedienungsanleitung
Dimplex
Dimplex DXC20 Bedienungsanleitung
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung