Dimplex CDFI1000P Bedienungsanleitung

Owner’s Manual

Model

CDFI1000P

6909660100

7214300100R04

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use the wall mount unit. For your safety,

always comply with all warnings and safety instructions contained in

this manual to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this unit.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ....................3

IMPORTANT INSTRUCTIONS ..................4

Installation..................................6

Cassette Plumbing....................................6

New Construction.....................................7

Operation Preparation .................................9

Bathroom Installation .................................10

Operation..................................12

Maintenance...............................15

Accessories ...............................16

Warranty .................................17

Welcome & Congratulations

Thank you and congratulations for purchasing an Optimyst®cassette

from Dimplex. Please use our convenient online registration page to

record your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Serial Number

Label Rating Label with

Model Number

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always be

followed to reduce the risk of fire,

electric shock, and injury to per-

sons, including the following:

①Read all instructions before us-

ing the unit.

② Do not operate any unit if the

unit has been dropped or damaged

in any manner. Contact Dimplex

Technical Service at 1-888-346-

7539.

③ Do not use outdoors.

④ Extreme caution is necessary

when any heater is used by or near

children or invalids and whenever

the heater is left operating and

unattended.

⑤ Do not operate any heater after

it malfunctions. Disconnect power

at service panel and have heater

inspected by a reputable electrician

before reusing.

⑥ To disconnect the unit, turn the

controls off, disconnect power at

the service panel.

⑦ Do not insert or allow foreign

objects to enter any ventilation or

exhaust opening as this may cause

an electric shock or re, or damage

the heater.

⑧ To prevent a possible re, do not

IMPORTANT INSTRUCTIONS

block air intakes or exhaust in any

manner.

⑨ All electrical heaters have hot

and arching or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable liquids

are used or stored.

⑩ Do not modify the unit. Use it

only as described in this manual.

Any other use not recommended by

the manufacturer may cause re,

electric shock or injury to persons.

⑪ Do not burn wood or other mate-

rials in the unit.

⑫ Always use a certied electrician

should new circuits or outlets be

required.

⑬ Disconnect the power supply

before performing any cleaning,

maintenance or relocation of the

unit.

⑭When transporting or storing the

unit, keep in a dry place, free from

excessive vibration and store so as

to avoid damage.

SAVE THESE INSTRUCTIONS

WARNING: Remote control con-

tains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by the

party responsible for compliance

could void user's authority to oper-

ate the equipment.

CAUTION: This equipment has been

tested and found to comply with the limits

for Class B digital device, pursuant to part

15 of the FCC Rules. These limits are

designed to provide reasonable protection

against harmful interference in a residen-

tial installation. This equipment generates,

uses and can radiate radio frequency

energy and, if not installed and used in ac-

cordance with the instructions, may cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user

IMPORTANT INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

is encouraged to try to correct the interfer-

ence by one or more of the following

measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and the receiver.

• Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device may

not cause harmful interference, and (2)

this device must accept any interference

received, including interference that may

cause undesired operation.

FCC CAUTION: Any changes or

modications not expressly approved by

the party responsible for compliance could

void the user’s authority to operate this

equipment.

6 www.dimplex.com

Installation

The CDFI1000 is supplied in an

assembled state and is designed to

be permanently installed. The unit

comes ready for hardwire installa-

tion and the use of the water rell

containers.

WARNING: Construction and

electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: To reduce the risk of

re, do not store or use gaso-

line or other ammable vapours

or liquids in the vicinity of the

heater.

!NOTE: A 15 Amp, 120 Volt cir-

cuit is required. A dedicated circuit

is preferred but not essential in all

cases. A dedicated circuit will be

required if, after installation, the cir-

cuit breaker trips or the fuse blows

on a regular basis when the heater

is operating. Additional appliances

on the same circuit may exceed the

current rating of the circuit breaker.

WARNING: Failure to install the

cassette as instructed below

may result in damage to the

equipment and or may expose

the user to the risk of re, ser-

ious injury, illness or death.

WARNING: Do not attempt to

wire your own new outlets or

circuits. To reduce the risk of

re, electric shock or injury to

persons, always use a licensed

electrician.

WARNING: Ensure that the

On/Off switch is set to the Off

position (refer to Operation

section) and that the circuit on

which the unit is to be installed

has the power cut off at the

service panel until installation is

complete.

!NOTE: Please read all instruc-

tions before installing.

Cassette Plumbing

The unit comes equipped with rell

containers for manual lling of the

reservoir. The unit can be hard

plumbed with the Dimplex plumbing

accessory kit - available from your

local Dimplex dealer, or with stan-

dard 1/4 in. (6.4 mm) tubing, using

the information outlined below.

!NOTE: The plumbing accessory

kit is designed for use with copper

piping.

CAUTION: Ensure that all

plumbing connections meet local

plumbing code requirements.

CAUTION: Ensure that the

location of the plumbing connection

allows for easy access to allow for

shutoff during scheduled mainten-

Installation

ance.

1. Locate a cold water line in the

vicinity of the desired location of

the cassette.

!NOTE: Normal tap water can

be used in the Optimyst®as long as

the tap water is not considered to

be hard water. In the event your tap

water is hard, softened or ltered

water is recommended.

2. Turn OFF the main water supply

and drain the line of any stand-

ing water (if possible), before

proceeding to tie into the water

line.

3. On the cassette, remove the

top cover assemblies and prime

each of the water reservoirs with

33.5 oz (1L) of water.

4. Replace the top cover assem-

blies and ensure that the two

plumbing caps are securely

attached to the top cover of the

water reservoirs.

5. Locate the ball valve located

in the bottom center of the unit

(near the back). (Figure 1)

6. Attach one end of the ¼ in. (6.4

mm) tubing to the ball valve,. In-

sert the tubing into the ball valve

tting so that it is fully inserted

(approximately ½” (12 mm)).

!NOTE: Ensure that the end of

the tubing is cut square, to prevent

leaking.

7. Route the tubing to the area of

the water source.

8. Verify that all of the connections

are fully inserted, and begin

opening each of the valves, en-

suring that no leaks are present.

!NOTE: The unit is equipped

with three levels of water control

management.

New Construction

CAUTION: When determining a

location for the Optimyst®cassette,

ensure that the unit will not be suscept-

ible to drafts, vents, ceiling fans and

other air currents. Similar to a candle,

large movements of air will affect the

unit’s ability to create and maintain the

ame effect.

1. Use studs to frame an enclos-

ure with the following minimum

internal/opening dimensions:

Media Plate - 40 ⅜ in. (1025

mm) wide, 12 ¼ in. (310 mm)

deep and the height can be

adjusted from 9 in. (229 mm) to

9 ½ in. (241 mm) by turning the

Figure 1

Ball Valve

To water source

8 www.dimplex.com

Installation

feet on the bottom of the unit.

Logset - 40 ⅜ in. (1025 mm)

wide, 14 ¼ in. (360 mm) deep

and the height can be adjusted

from 9 in. (229 mm) to 9 ½ in.

(241 mm) by turning the feet on

the bottom of the unit

!NOTE: It is recommended

that during drywall installation and

nishing the media tray be installed

with the provided bag to prevent

dust and debris from entering the

unit.

!NOTE: For optimal perform-

ance, a clearance of 18 in. (457

mm) between the installation sur-

face and any surface above should

be maintained. A minimum clear-

ance of 12 in. (305 mm) must be

maintained.

2. In the back right corner of the

unit, locate and remove the

electrical cover plate, by remov-

ing the two securing screws.

3. Install a ⅜ in. (10 mm) or ½ in.

(13 mm) cable connector, not

included, suitable for mounting

in a ⅞ in. (22 mm) hole, to the

cable plate and feed the supply

cable through the connector.

The cable plate can be removed

by removing the two securing

screws on either side, to allow

for easier access.

CAUTION: Use two conductor,

non-metallic sheath cable with

ground wire (3 wires total) for the

incoming power supply on replace

inserts. Use appropriate wire to

meet local and national electrical

codes for rated power.

!NOTE: When installing multiple

8.50 in. (216 mm)

40.08 in. (1018 mm)

Logset: 13.94 in. (353 mm)

Adjustable from

9.0 in. (224 mm)

to 9.5 in. (241 mm)

11.94 in. (303 mm)

40.08 in. (1018 mm)

Media Plate: 11.94 in. (303 mm)

!NOTE: When prepar-

ing the opening for the unit

¼ in. (6.4 mm) of clearance

should be maintained from

each surface to ensure easy

installation.

Product Dimensions

Installation

units in the same vicinity they will

need to be wired in parallel.

!NOTE: The Optimyst®cassette

is designed to allow for installa-

tion of a wall switch to control the

incoming power to the unit.

4. Connect the black wire (live)

from the unit to the live from the

power supply.

5. Connect the white wire (neutral)

from the unit to the neutral wire

from the power supply.

6. Connect the green wire (ground)

from the unit to the ground wire

from the power supply.

7. Place all connectors inside the

unit and secure the cable clamp

to unit, making sure that the

cable clamp grips only the jacket

of service cable.

WARNING: Ensure the power

wiring is not installed so that it is

pinched or against a sharp edge

and ensure that the power wir-

ing is stored or secured to avoid

tripping or snagging to reduce

the risk of re, electric shock or

injury to persons.

8. Install the unit into the roughed

in framing ensuring that the unit

is resting on two framing sills,

one at the front and one at the

back or a level surface.

9. Level the housing - right to left

and front to back, using the 6

adjustable feet on the bottom of

the unit.

10.Secure the unit to the perma-

nent framing on either end

through a minimum of two holes

(Figure 2).

!NOTE: An air inlet that is a min-

imum of 72 in2(460 cm2) is required

for optimum mist production (Figure

3).

Operation Preparation

1. After the surrounding area has

been dry walled and nished,

remove the media plate from the

unit.

2. Install the tethered controller

into the jack on the right hand

side of the unit and run the cord

around the internal components

and out through the small open-

ing in the back panel. (Figure 2)

Figure 2

Cable Plate

Electrical Cover Plate

Holes for

securing to

framing

Cord Outlet

for Tethered

Controller

10 www.dimplex.com

Installation

3. Locate the tethered controller

so that:

a) it can be easily accessed, if

being used as the main controls,

b) it is not obscured by either

bricks or sheet metal so that

the signal that is sent from the

remote control can be easily

picked up.

4. Initialize the tethered controller

to the remote (see operation

section).

5. Fill the unit:

•RellConatiners - remove

the ll cap assemblies from the

inlet to the reservoir tanks, then

install the rell containers.

!NOTE: During initial installa-

tion, the Rell Container should

be relled after the Reservoir

has lled to ensure the max-

imum operating time.

•Hard Plumbed - prime each of

the water reservoirs with 33.5 oz

(1L) of water.

!NOTE: Normal tap water can

be used in the Optimyst®as long as

the tap water is not considered to

be hard water. In the event your tap

water is hard, you may use soft-

ened water or distilled water with

1/8 tsp. of salt (0.5 mL) added to

the water reservoir. (The addition of

additional salt should only be used

when you notice that the unit is not

producing mist as expected.)

6. Install the media tray or logset

accessory on top.

!NOTE: If the intention is to ac-

cessorize the unit with something

other than just the media tray or

logset, ensure that media used

does not have the ability to create

small particles that may fall into the

unit or has a overall weight above 5

lbs (2.3 kg).

>72 in2

(>460 cm2)

>72 in2

(>460 cm2)

>72 in2

(>460 cm2)

Figure 3

Andere Handbücher für CDFI1000P

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex X40003BK Bedienungsanleitung

Dimplex

Dimplex DNV20AB Bedienungsanleitung

Dimplex

Dimplex Braemar Optiflame 3D BMR20 Series Bedienungsanleitung

Dimplex

Dimplex Chadwick Suite CDW15WW Bedienungsanleitung

Dimplex

Dimplex 6908760100 Bedienungsanleitung

Dimplex

Dimplex CDFI500P Bedienungsanleitung

Dimplex

Dimplex Atherton ATH20-INT Bedienungsanleitung

Dimplex

Dimplex Auvergne Log 2920 Bedienungsanleitung

Dimplex

Dimplex DF1870L Bedienungsanleitung

Dimplex

Dimplex BF33ST/DX Bedienungsanleitung

Dimplex

Dimplex Albany Optimyst ABN15-RGB-EU Bedienungsanleitung

Dimplex

Dimplex EWF-SS Bedienungsanleitung

Dimplex

Dimplex RLG20BR Bedienungsanleitung

Dimplex

Dimplex 6908760100 Bedienungsanleitung

Dimplex

Dimplex EF3003 Bedienungsanleitung

Dimplex

Dimplex DFB4047 Kurzanleitung

Dimplex

Dimplex DF2550-EU Bedienungsanleitung

Dimplex

Dimplex CFP4949BW Bedienungsanleitung

Dimplex

Dimplex PF3033 Bedienungsanleitung

Dimplex

Dimplex ELECTRALOG DF203A Bedienungsanleitung

Dimplex

Dimplex Diamantique Bedienungsanleitung

Dimplex

Dimplex DC700 Bedienungsanleitung

Dimplex

Dimplex BFSL33 Bedienungsanleitung

Dimplex

Dimplex BLF5051-AU/PRISM 50" Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung