Dimplex DF3033ST Bedienungsanleitung

Owner’s Manual

Model

DF3033ST

To view the full line of Dimplex products, please visit

www.dimplex.com

7209120100rev02

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

2 www.dimplex.com

Welcome & Congratulations ........................3

Important Safety Instructions ........................4

Quick Reference Guide ............................6

Site Selection and Preparation ......................6

Fireplace Installation ..............................7

Operation ......................................10

Maintenance ...................................16

Warranty ......................................19

Replacement Parts List ...........................23

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are

considered important

enough to emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result

in damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations

Thank you and congratulations for

choosing to purchase an electric

replace from Dimplex, the world

leader in electric replaces.

Please carefully read and save

these instructions.

CAUTION: Read all

instructions and warnings

carefully before starting

installation. Failure to follow

these instructions may result

in a possible electric shock,

re hazard and will void

the warranty.

Please record your model and

serial numbers below for future

reference: model and serial

numbers can be found on the

Model and Serial Number Label

of your replace.

NO NEED TO RETURN

TO THE STORE

Questions With the Assembly?

Require Parts Information?

Product Under Manufacturer’s

Warranty?

Call Toll-Free

1-888-346-7539

Monday to Friday

8:00 a.m. to 4:30 p.m. EST

Please have your model

number and product serial

number ready. (See below)

Model Number

Serial Number

4 www.dimplex.com

①Read all instructions before

using the electric replace.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The

trim around the heater outlet

becomes hot during heater

operation. Keep combustible

materials, such as furniture,

pillows, bedding, papers, clothes,

and curtains at least three (3) feet

(0.9 m) from the front of the unit.

③Extreme caution is necessary

when any heater is used by or

near children or invalids and

whenever the unit is left operating

and unattended.

④Always unplug the electric

replace when not in use.

⑤Do not operate any unit with

a damaged cord or plug, or if

the heater has malfunctioned,

or if the electric replace has

been dropped or damaged in

any manner. Return heater

to authorized service facility

for examination, electrical or

mechanical adjustment, or repair.

⑥Do not use outdoors.

⑦ The electric replace is not

IMPORTANT SAFETY INSTRUCTIONS

intended for use in bathrooms,

laundry areas and similar indoor

locations. Never locate heater

where it may fall into a bathtub or

other water container.

⑧Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc

area and where it will not be

tripped over.

⑨To disconnect the unit, turn

the controls off, then remove the

plug from the outlet.

⑩Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑪ To prevent a possible re, do

not block air intake or exhaust

in any manner. Do not use on

soft surfaces, like a bed, where

openings may become blocked.

⑫All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored or

where the unit will be exposed to

ammable vapors.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

⑬Do not modify the electric

replace. Use it only as described

in this manual. Any other use not

recommended by the

manufacturer may cause re,

electric shock or injury to persons.

⑭Avoid the use of an extension

cord or power bar. Extension

cords and power bars may

overheat and cause a risk of re.

If you must use an extension cord

or power bar, it must be No. 14

AWG minimum size and rated for

no less than 1875 Watts.

⑮ Do not burn wood or other

materials in the electric replace.

⑯ Do not strike the replace

glass.

⑰ Always use a certied

electrician should new circuits or

outlets be required.

⑱Always use properly

grounded, fused and polarized

outlets.

⑲Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

⑳When transporting or storing

the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

6 www.dimplex.com

Site Selection and Preparation

Quick Reference Guide

① Prior to the rst use of the

replace verify the following:

• Are the circuit breakers for the

unit on?

• Are the light bulbs in your

replace loose? (To check, follow

the instructions for replacing the

light bulbs under the Maintenance

section of this manual.)

② The heater on your replace

may emit a slight, harmless odor

when rst used. This odor is a

normal condition caused by the

initial heating of internal heater

parts and will not occur again.

③The information regarding the

model of your replace can be

found on the rating plate located

on the top of the unit.

!NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not

essential in all cases. A

dedicated circuit will be

required if, after installation,

the circuit breaker trips or fuse

blows on a regular basis when

the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

WARNING: Ensure the power

cord is not installed so that it

is pinched or against a sharp

edge and ensure that the

power cord is stored or

secured to avoid tripping or

snagging to reduce the risk

of re, electric shock or injury

to persons.

Construction and electrical

outlet wiring must comply with

local building codes and other

applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

always use a licensed

electrician.

Site Selection and Preparation

This section provides instructions

for selecting a location and

preparing the site to install the

replace into your Dimplex mantel

surround.

①Select a suitable location that

is not susceptible to moisture and

is away from drapes, furniture and

high trafc.

②For ease of electrical hook

up you may wish to locate the

Fireplace Installation

replace near an existing outlet

(refer to NOTE 1).

③ Store the replace in a safe

dry and dust free location.

!NOTE: The dimensions of

the replace are 31 ½ inches

(800 mm) wide x 22 ⅜ inches

(568 mm) high x 9 ⅛ inches

(232 mm) deep. The replace

does not require any additional

venting.

① Install the replace assembly

into the mantel (refer to mantel

assembly instructions).

!NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not

essential in all cases. A

dedicated circuit will be

required if, after installation,

the circuit breaker trips or fuse

blows on a regular basis when

the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

!IMPORTANT: If not using a

Dimplex mantel, the replace

must be installed in an

enclosure with the following

minimum internal/opening

dimensions (Figure 1).

8 www.dimplex.com

Fireplace Installation

New Wall Construction

①Select a suitable location that

is not susceptible to moisture and

is away from drapes, furniture and

high trafc.

② Place the replace in the

desired location to see how it will

look in the room.

③Mark the desired location on

the oor and store the replace in

a safe, dry and dust free location.

④ Use studs to frame an

opening of 31 ¾ inches (807 mm)

wide x 22 ¾ inches (578 mm)

high x 9 ½ inches (241 mm) deep.

Figure 1

22 ¾”

(578 mm)

31 ¾”

(807 mm)

9 ½”

(241 mm)

Option #1 - The power cord can

be lead from behind the trim and

along the wall to an outlet near

the replace.

Option #2 - A new outlet can be

installed inside the new frame

construction. Plug the unit into

a 15 Amp, 120 Volt outlet. If the

cord does not reach, you may

use an extension cord rated for a

minimum of 1875 Watts.

Option #3 - Hardwire

①Wire a dedicated, properly

fused circuit with 120 Volt,

15 Amp rating. Allow up to eight

(8) feet (2.4 m) of service cable

for connecting power supply to

junction box on replace when

installing after nishing wall.

CAUTION: Use two

conductor, non-metallic sheath

cable with ground wire (three

(3) wires total) for the incoming

power supply on replace

inserts. Use appropriate wire

to meet local and national

electrical codes for rated

power consumption.

②Remove the outer jacket and

Fireplace Installation

strip the individual conductor from

the end.

③Loosen the screw securing

the junction box cover and

remove the cover.

④Take the cables out from the

junction box, loosen the two wire

twist nuts and remove the cord

set (Figure 2).

⑥Connect the black wire (live)

from the unit to the black wire

from power supply (Figure 3).

⑦Connect the white wire

(neutral) from the unit to the white

wire from power supply

(Figure 3).

⑧Connect the green wire

(ground) from the unit to the

green wire from power supply

(Figure 3).

Figure 2

⑤Route the power supply wire

through the knockout on supplied

alternative junction box cover

and secure with a wire clamp (not

supplied) (Figure 3).

Fireplace

Junction

Box

White wire (N)

Black wire (L)

Green wire (G) Green wire (G)

Black wire (L)

White wire (N)

120 V Power

Supply

(Breaker Panel)

Figure 3

10 www.dimplex.com

Fireplace Installation

⑨Place all connectors inside

the unit and secure the junction

box cover to unit. Ensure that the

cable clamp grips only the jacket

of service cable.

CAUTION: Clearance for

air circulation beneath the

replace insert is provided by

two (2) rubber feet.

Do not install the replace

insert directly on carpet or

similar surfaces which may

restrict air circulation.

If installing the replace in a

carpeted area, place a one-

piece, solid, at surface under

the replace insert. Ensure

that both of the insert’s feet

rest securely on this surface.

Operation

Electric Fireplace Manual

Control

The manual controls for the

replace are located in the upper

right hand corner (Figure 4).

A. Main On/Off Switch

Supplies power to the 3 Position

Manual Control Switch.

B. 3 Position Manual Control

Switch

Remote (left position): The

unit is operated with the remote

control.

Flame (center position): The

ame effect is turned on.

Flame & Heat (right position):

The ame effect and heater are

turned on simultaneously. When

the manual control is in the Flame

& Heat position the heater does

Figure 4

ABC

Andere Handbücher für DF3033ST

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex BLF3451-INT Bedienungsanleitung

Dimplex

Dimplex Braemar Optiflame 3D BMR20 Series Bedienungsanleitung

Dimplex

Dimplex DFB6016 Kurzanleitung

Dimplex

Dimplex Lee LEE20 Benutzerhandbuch

Dimplex

Dimplex Vivente VVT125 Handbuch

Dimplex

Dimplex EWM-COPPER Kurzanleitung

Dimplex

Dimplex VALENCIA VAL15 Bedienungsanleitung

Dimplex

Dimplex Optiflame Electric Fireplace Bedienungsanleitung

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Bedienungsanleitung

Dimplex

Dimplex Optiflame Gorstan GST20 Bedienungsanleitung

Dimplex

Dimplex Sierra 48 Bedienungsanleitung

Dimplex

Dimplex DF2426GB Bedienungsanleitung

Dimplex

Dimplex Siena Fire SNA20 Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3015 Bedienungsanleitung

Dimplex

Dimplex EF2870 Bedienungsanleitung

Dimplex

Dimplex BLF74 Bauanleitung

Dimplex

Dimplex MINICUBE Bedienungsanleitung

Dimplex

Dimplex BLF3451 Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3015 Kurzanleitung

Dimplex

Dimplex DC700 Bedienungsanleitung

Dimplex

Dimplex DWF1203B Bedienungsanleitung

Dimplex

Dimplex SP820 Bedienungsanleitung

Dimplex

Dimplex DF3033ST Bedienungsanleitung

Dimplex

Dimplex Revillusion Osbourne Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung