Dimplex DFG2562 Bedienungsanleitung

Owner’s Manual

Model

DFG2562

DFG253A

7210580100R08

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures

and techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations ..................3

Important Instructions ........................4

Installation ................................7

Operation ................................10

Maintenance ..............................13

Warranty .................................15

Replacement Parts .........................18

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your replace.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

S E R IAL No.

MODE L

MOD.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before us-

ing the electric replace.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the electric

replace when not in use.

⑤ Do not operate any heater after

it malfunctions. Disconnect power

at the service panel and have the

heater inspected by a reputable

electrician before reusing.

⑥ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at 1-888-346-7539.

IMPORTANT INSTRUCTIONS

⑦Do not use outdoors.

⑧ The electric replace is not

intended for use in bathrooms,

laundry areas and similar indoor

locations. Never locate heater

where it may fall into a bathtub or

other water container.

⑨ Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑩ To disconnect the unit, turn the

controls off, then remove the plug

from the outlet

⑪ Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑫ To prevent a possible re, do

not block air intake or exhaust in

any manner.

⑬ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable

liquids are used or stored.

⑭ Do not modify the electric re-

place. Use it only as described

SAVE THESE INSTRUCTIONS

in this manual. Any other use not

recommended by the manufactur-

er may cause re, electric shock

or injury to persons.

⑮ To reduce the risk of electric

shock, this appliance has a polar-

ized plug (one blade is wider than

the other). This plug will t in a

polarized outlet only one way. If

the plug does not t fully in the

outlet, reverse the plug. If it still

does not t, contact a qualied

electrician to install the proper

outlet. Do not change the plug in

any way.

⑯ Always plug heaters directly

into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰ Do not burn wood or other ma-

terials in the electric replace.

⑱ Do not strike the replace

glass.

⑲ Always use a certied electri-

cian should new circuits or outlets

be required.

⑳ Always use properly grounded,

fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

!NOTE: This equipment has been

tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and

can radiate radio frequency energy

and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

or television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

· Reorient or relocate the receiving

antenna.

· Increase the separation between

the equipment and the receiver.

· Connect the equipment into an

outlet on a circuit different from that

to which the receiver is connected.

· Consult the dealer or an

experienced radio/TV technician for

help.

Operation is subject to the following

two conditions: (1) this device may not

cause interference and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

IMPORTANT INSTRUCTIONS

WARNING: Remote control

contains small batteries. Keep

away from children. If swallowed,

seek medical attention immedi-

ately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by

the party responsible for compli-

ance could void user's authority to

operate the equipment.

Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

CAUTION: Clearance for air

circulation beneath the re-

place insert is provided by 2

rubber feet.

Do not install the replace

insert directly on carpet or

similar surfaces which may

restrict air circulation.

CAUTION: If installing the

replace in a carpeted area, place

a one-piece, solid, at surface

under the replace. Ensure that

both of the feet rest securely on

this surface.

!NOTE: The dimensions of the

rebox are 26 in. (661 mm)

wide X 18 ⅞ in. (480 mm) high

X 8 ¾ in. (223 mm) deep. The

rebox does not require any

additional venting.

Mantel Installation

Install the replace into the

mantel (refer to mantel assembly

instructions).

!IMPORTANT: If not using a

Dimplex mantel, the replace

must be installed in an enclosure

with the following minimum inter-

nal/opening dimensions - Figure

Figure 1

9 in.

(229 mm)

24 ½ in.

(622 mm)

18 ¼ in.

(464 mm)

8 www.dimplex.com

Installation

Figure 2

Figure 3

New Wall Construction

1. Mark the desired location on

the oor and store the re-

place in a safe, dry and dust

free location.

2. Use studs to frame an open-

ing of 24 ½ in. (622 mm) wide

X 18 ¼ in. (463.6 mm) high

X 8 ⅞ in. (225.5 mm) deep.

(Figure 1)

Option #1 - The power cord can

be lead from behind the trim

and along the wall to an outlet

near the replace.

Option #2 - A new outlet can be

installed inside the new frame

construction. Plug the unit into

a 15 Amp/120 Volt outlet.

!NOTE: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not es-

sential in all cases. A dedi-

cated circuit will be required

if, after installation, the circuit

breaker trips or fuse blows

on a regular basis when the

heater is operating. Additional

appliances on the same circuit

may exceed the current rating

of the circuit breaker.

Option #3 - Hardwire

1. Wire a dedicated, properly

fused circuit with 120 Volt, 15

Amp rating. Allow up to 8 feet

of service cable for connect-

ing power supply to junction

box on replace when install-

ing after nishing wall.

CAUTION: Use two conduc-

tor, non-metallic sheath cable

with ground wire (3 wires total)

for the incoming power supply on

replace inserts. Use appropriate

wire to meet local and national

electrical codes for rated power

Installation

consumption.

2. Remove the outer jacket and

strip the individual conductor

from the end.

3. Loosen the screw securing

the junction box cover and

remove the cover.

4. Take the cables out from the

junction box, loosen the two

wire twist nuts and remove

the cord set (Figure 2).

5. Route the power supply wire

through the knockout on sup-

plied alternative junction box

cover and secure with a wire

clamp (not supplied) (Figure

3).

6. Connect the black wire (live)

from the unit to the black wire

from power supply (Figure 3).

7. Connect the white wire

(neutral) from the unit to the

white wire from power supply

(Figure 3).

8. Connect the green wire

(ground) from the unit to the

green wire from power supply

(Figure 3).

9. Place all connectors inside

the unit and secure the junc-

tion box cover to unit. Ensure

that the cable clamp grips

only the jacket of service

cable.

Wiring

SWITCH OUT

CUTOUT THERMOSTAT

HEAT ON/OFF

SWITCH

LIGHT HARNESS

ASSEMBLY

FLICKER

MOTOR

CAPACITOR

BLOWER

MOTOR

ELEMENT

10 www.dimplex.com

Installation

Operation

WARNING: This electric

rebox must be properly installed

before it is used.

Manual Controls

A. 3-Position Switch

The switch has two On positions

marked “ I” and “ II ”.

The “ I” position is for manual op-

eration. In this position the built-in

remote control is by-passed.

The “ II ” position is for operating

the unit with the provided remote

control. When in the remote

control (“ II ”) position the unit is

operated with the ON and OFF

buttons of the remote control.

When the switch is in the center

“ O ” position the unit is off.

Figure 4

Front glass

Mounts

Hooks

Final Steps

Carefully pour and evenly distrib-

ute the supplied glass rock media

on the front tray of the rebox

(Figure 4). Once complete, hang

the front glass assembly on the

mounts of the rebox.

B. Heater On/Off Switch

The Heater On/Off Switch sup-

plies power to the heater fan

and the heater element. When the

switch is in the On position, the

heater operates if the thermostat

calls for heat.

C. Heater Thermostat Control

To adjust the temperature to your

individual requirements, turn the

thermostat control clockwise all

the way to turn on the heater.

When the room reaches the de-

sired temperature, turn the ther-

mostat knob counter-clockwise

until you hear a click. Leave in

this position to maintain the room

temperature at this setting. For

additional heat, turn clockwise un-

Andere Handbücher für DFG2562

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex CAS400LNH-INT Bedienungsanleitung

Dimplex

Dimplex BLF50 Bedienungsanleitung

Dimplex

Dimplex DS3311 Bedienungsanleitung

Dimplex

Dimplex Optiflame Electric Fireplace Bedienungsanleitung

Dimplex

Dimplex Indoor Electric Fireplace Bedienungsanleitung

Dimplex

Dimplex DWOP20R Bedienungsanleitung

Dimplex

Dimplex DF2426 Bedienungsanleitung

Dimplex

Dimplex DF3020-EU Bedienungsanleitung

Dimplex

Dimplex 5011139048455 Bedienungsanleitung

Dimplex

Dimplex GDS23L8-1904GB Bedienungsanleitung

Dimplex

Dimplex EF2570G Bedienungsanleitung

Dimplex

Dimplex PRISM BLF3451-AU Bedienungsanleitung

Dimplex

Dimplex TOLUCA TLC20 Bedienungsanleitung

Dimplex

Dimplex EF2870 Bedienungsanleitung

Dimplex

Dimplex DWOP20R Bedienungsanleitung

Dimplex

Dimplex Optiflame MiniMozart FGA15E Bedienungsanleitung

Dimplex

Dimplex DIMPLEX ELECTRIC FIREPLACE Betriebsanleitung

Dimplex

Dimplex DFG3033 Bedienungsanleitung

Dimplex

Dimplex X-XLF5017-XD Bedienungsanleitung

Dimplex

Dimplex BLF50 Bedienungsanleitung

Dimplex

Dimplex 3-STEP Optimyst Bedienungsanleitung

Dimplex

Dimplex DF2608 Bedienungsanleitung

Dimplex

Dimplex IN-STUD V1525BT Bedienungsanleitung

Dimplex

Dimplex BLF50 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch