Dimplex DWOP20R Bedienungsanleitung
Owner’s Manual
Model
DWOP20R
DWOP20BR
6909030100
7212770100R04
IMPORTANT SAFETY INFORMATION: Always read this manual
rst before attempting to install or use the wall mount engine. For
your safety, always comply with all warnings and safety instructions
contained in this manual to prevent personal injury or property
damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
2 www.dimplex.com
Table of Contents
Always use a qualied technician
or service agency to repair
this engine.
!NOTE: Procedures and
techniques that are considered
important enough to
emphasize.
CAUTION: Procedures and
techniques which, if not
carefully followed, will result in
damage to the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations ....................3
IMPORTANT INSTRUCTIONS ..................4
Installation ..................................6
Assembly ...................................9
Operation ..................................11
Maintenance ...............................14
Warranty .................................16
Replacement Parts ..........................18
3
Welcome & Congratulations
Thank you and congratulations for choosing to purchase an Optimyst®
wall mount engine from Dimplex, the world leader in electric replaces.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, re hazard and will void the warranty.
Please record your model and serial numbers below for future
reference: model and serial numbers can be found on the Model and
Serial Number Label of your wall mount engine.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and product serial
number ready. (See above)
Model Number
Serial Number
4 www.dimplex.com
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
① Read all instructions before
using the engine.
②
The heater is hot when in use.
To avoid burns, do not let bare skin
touch hot surfaces. The trim around
the heater outlet becomes hot
during heater operation.
DANGER:
High temperatures
may be generated under certain
abnormal conditions. Do not
partially of fully cover the front of
this heater.
③
Extreme caution is necessary
when any heater is used by or near
children or invalids and whenever
the unit is left operating and
unattended.
④ Always unplug the engine
when not in use.
⑤ Do not operate any unit with
a damaged cord or plug, or if
the engine has been dropped or
damaged in any manner. Contact
Dimplex Technical Service at
1-888-346-7539.
⑥ Do not use outdoors.
⑦ The engine is not intended for
use in bathrooms, laundry areas
IMPORTANT INSTRUCTIONS
and similar indoor locations.
Never locate unit where it may
fall into a bathtub or other water
container.
⑧ Do not run the cord under
carpeting. Do not cover cord with
throw rugs, runners, or the like.
Arrange cord away from trafc
area and where it will not be
tripped over.
⑨ To disconnect the unit, turn the
controls off, then remove the plug
from the outlet.
⑩ Always use properly grounded,
fused and polarized outlets.
⑪
Do not insert or allow foreign
objects to enter any ventilation or
exhaust opening as this may cause
an electric shock or re, or damage
to the heater.
⑫
To prevent a possible re, do
not block air intake or exhaust
in any manner. Do not use on
soft surfaces, like a bed, where
openings may become blocked.
⑬
All electrical heaters have hot
and arching or sparking parts inside.
Do not use in areas where gasoline,
paint, or ammable liquids are used
or stored or where the unit will be
exposed to ammable vapors.
⑭ Do not modify the engine.
Use it only as described in
5
SAVE THESE INSTRUCTIONS
this manual. Any other use
not recommended by the
manufacturer may cause re,
electric shock or injury to persons.
⑮
To reduce the risk of electric
shock, this appliance must be
grounded. Avoid the use of an
extension cord. Extension cords
may overheat and cause a risk of
re. Always plug heaters directly
into a wall outlet/receptacle. Never
use with an extension cord or
relocatable power tap (outlet/power
strip).
⑯ Do not burn wood or other
materials in the engine.
⑰ Always use a certied
electrician should new circuits or
outlets be required.
⑱ Disconnect the power supply
before performing any cleaning,
maintenance or relocation of the
unit.
⑲
When transporting or storing
the unit and cord, keep in a
dry place, free from excessive
vibration and store so as to avoid
damage.
⑳ The wall mount engine must
not be located directly below a
socket outlet.
㉑ The wall mount engine must
be positioned so that the plug is
accessible.
WARNING: Remote control
contains small batteries.
Keep away from children. If
swallowed, seek medical attention
immediately.
WARNING: Do not install
battery backwards, charge, put
in re or mix with used or other
battery types - may explode or
leak causing injury.
!NOTE: Changes or
modications not expressly
approved by the party responsible
for compliance could void
user's authority to operate the
equipment.
IMPORTANT INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
6 www.dimplex.com
Installation
WARNING: Ensure the power
cord is not installed so that it is
pinched or against a sharp edge
and ensure that the power cord is
stored or secured to avoid tripping
or snagging to reduce the risk
of re, electric shock or injury to
persons.
WARNING: Construction
and electrical outlet wiring must
comply with local building codes
and other applicable regulations
to reduce the risk of re, electric
shock and injury to persons.
WARNING: Do not attempt
to wire your own new outlets or
circuits. To reduce the risk of re,
electric shock or injury to persons,
always use a licensed electrician.
WARNING: To reduce the risk
of re, do not store or use gaso-
line or other ammable vapors or
liquids in the vicinity of the heater.
!NOTE: A 15 Amp, 120 Volt cir-
cuit is required. A dedicated circuit
is preferred but not essential in all
cases. A dedicated circuit will be
required if, after installation, the
circuit breaker trips or the fuse
blows on a regular basis when the
heater is operating. Additional ap-
pliances on the same circuit may
exceed the current rating of the
circuit breaker.
Wall Hanging Instructions
WARNING: The supplied
mounting components are
designed for use with Dim-
plex wall mounted engines
only. Improper use, or use for
purposes other than intended,
may cause damage or injury.
WARNING: Failure to install
the replace as instructed
below may result in damage
to the equipment and or may
expose the user to the risk of
re, serious injury, illness or
death.
1. Remove the two screws that
secure the hanging bracket to
the back of the rebox.
(Figure 1)
WARNING: The replace
requires the wall hanging
bracket screws to be installed
into a minimum of one wall
stud.
2. Select an appropriate location
to mount the unit on a wall,
above an electrical outlet.
Access to the electrical outlet
must be maintained. Ensure
the installation meets the
national and state/provincial
electrical codes.
7
40 in (1020 mm)
RECOMMENDED
24.6in. (625mm)
Minimum
Installation
Figure 1
CAUTION: A minimum of
24.6in. (625mm) from a corner, is
recommended for optimum airow
and ame production.
!NOTE: It is recommended
that the bottom of the unit not
be mounted higher than 40 in.
(1020mm) from the Fireplace
Installation ground to maintain an
optimized viewing angle of the
ame. (Figure 2)
!NOTE: Wall anchors must be
installed in the appropriate wall lo-
cations to fasten the wall bracket
to drywall. (Figure 3)
3. Hold the wall hanging bracket
on the wall and mark the loca-
tion of ONE of the securing
holes.
4. Place the bubble level onto
the top of the wall hanging
bracket.
Figure 2
5. Adjust the wall hanging
bracket so the bubble on the
level is centered between the
two black lines.
6. Mark the two (2) screw loca-
tions, on the wall, ensuring
that the wall bracket stays
level.
7. Install the supplied wall an-
chors on the drywall marked
locations by placing a #2 Phil-
lips screwdriver into the recess
of the anchor.
8 www.dimplex.com
8. Press the anchor into the wall
in the desired marked posi-
tion while turning the anchor
clockwise until it is ush with
the wall.
9. Insert the wall anchor screws
through the wall bracket and
thread into the wall anchors.
Tighten the screw.
10. Install the remaining screw
through the bracket and into
the wall stud.
!NOTE: At least one of the
screws must be installed into a
wall stud.
11. Rotate the securing bracket
at bottom of the engine at
the back so that it is pointing
down. (Figure 3)
12. Mount the unit on the wall,
so that the tab on the engine
bracket has been inserted into
the hook on the wall bracket.
(Figure 4)
Installation
13. Secure the bottom of the wall
mounted engine to the wall
using the securing bracket and
the provided screw.
Figure 4
Figure 3
Wiring
9
Transducer
Rock
Media
Removable
Rell
Container
Light
Bulbs
Media Tray
Assembly
Figure 5
1. Carefully unpack all of the
components from the box.
(Figure 5)
2. Remove top cover by turning
the retaining tabs on both
ends of the water reservoir.
(Figure 6)
3. Install the light bulbs by
aligning the pins on the bulbs
and the xture and pressing
down until they are fully
inserted. (Figure 7)
4. Install the transducer so that
it is sitting level in the circular
Figure 6
holding area in the reservoir.
5. Orient transducer wire so that
it does not sit directly above
the emitter and the wire
passes through the slot in the
side of the tank. (Figure 7)
Top
Cover
Figure 7
Transducer
Emitter
Wire Slot
Remote
Control
10 www.dimplex.com
Assembly
6. Reinstall the top cover and
ensure both retaining tabs
have been turned so that they
are pointing inwards.
7. Fill and install the Rell
Container.
!NOTE: Normal tap water can
be used in the Optimyst® as long
as the tap water is not considered
to be hard water. In the event
your tap water is hard, you may
use softened water or distilled
water with 1/8 tsp of salt (0.5
mL) added to the water reservoir.
(The addition of additional salt
should only be used when you
notice that the unit is not produc-
ing mist as expected.)
!NOTE: During initial
installation, the Rell Container
should be relled after the
Reservoir has lled to ensure the
maximum operating time.
8. Install the media tray and
arrange the rock media on
top, so that the opening is not
blocked.
CAUTION: Do not arrange the
rock media while the unit is run-
ning, since the rocks may be hot.
9. Make sure the On/Off switch
is switched to Off (refer to
Operating Instruction section).
Figure 8
10. Plug the unit into a 15 Amp/
120 volt outlet.
Andere Handbücher für DWOP20R
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Dimplex Kamin im Innenbereich Handbücher
Dimplex
Dimplex CDN20-AU Bedienungsanleitung
Dimplex
Dimplex CAS500 Bedienungsanleitung
Dimplex
Dimplex MULTIFIRE DF3215 Kurzanleitung
Dimplex
Dimplex MIDI FIRE MIDI32B Bedienungsanleitung
Dimplex
Dimplex Vivente Bedienungsanleitung
Dimplex
Dimplex Wynford WYN20BR Bedienungsanleitung
Dimplex
Dimplex ALBANY ECO Technisches Handbuch
Dimplex
Dimplex EWM-COPPER Kurzanleitung
Dimplex
Dimplex DF28L-PRO Bedienungsanleitung
Dimplex
Dimplex CDFI1000P Bedienungsanleitung
Dimplex
Dimplex SP120 Bedienungsanleitung
Dimplex
Dimplex Optiflame Electric Fireplace Bedienungsanleitung
Dimplex
Dimplex EWF-SS Bedienungsanleitung
Dimplex
Dimplex EF3003 Kurzanleitung
Dimplex
Dimplex DF2500L Bedienungsanleitung
Dimplex
Dimplex 3-STEP Optimyst Bedienungsanleitung
Dimplex
Dimplex RBF30-AU Bedienungsanleitung
Dimplex
Dimplex BF33STP Kurzanleitung
Dimplex
Dimplex DWF-1326 Bedienungsanleitung
Dimplex
Dimplex DFI2310 Bedienungsanleitung
